1 files changed, 0 insertions, 78 deletions
diff --git a/demos/ARMCM0P-LPC812-LPCXPRESSO/mcuconf.h b/demos/ARMCM0P-LPC812-LPCXPRESSO/mcuconf.h
deleted file mode 100644
index d5b1abe95..000000000
--- a/demos/ARMCM0P-LPC812-LPCXPRESSO/mcuconf.h
+++ /dev/null
@@ -1,78 +0,0 @@
-/*
-    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-/*
- * LPC812 drivers configuration.
- * The following settings override the default settings present in
- * the various device driver implementation headers.
- * Note that the settings for each driver only have effect if the driver
- * is enabled in halconf.h.
- *
- * IRQ priorities:
- * 3...0        Lowest...highest.
- */
-
-/*
- * HAL driver system settings.
- */
-
-/* Default: Run PLL @24MHz from 12MHz IRC
-  #define LPC8xx_PLLCLK_SOURCE               SYSPLLCLKSEL_IRCOSC
-  #define LPC8xx_SYSPLL_MUL                  4
-  #define LPC8xx_SYSPLL_DIV                  4
-  #define LPC8xx_MAINCLK_SOURCE              SYSMAINCLKSEL_PLLOUT
-  #define LPC8xx_SYSABHCLK_DIV               1
-*/
-
-/*run directly from internal 12M osc...*/
-#define LPC8xx_MAINCLK_SOURCE              SYSMAINCLKSEL_IRCOSC
-
-/*
- * GPT driver system settings.
- */
-/* Defaults:
-  #define LPC8xx_GPT_USE_MRT0              TRUE
-  #define LPC8xx_GPT_USE_MRT1              FALSE
-  #define LPC8xx_GPT_USE_MRT2              FALSE
-  #define LPC8xx_GPT_USE_MRT3              FALSE
-  #define LPC8xx_GPT_MRT_IRQ_PRIORITY      2
-*/
-
-/*
- * PWM driver system settings.
- */
-
-/*
- * SERIAL driver system settings.
- */
-/* Defaults:
-  #define LPC8xx_SERIAL_USE_UART0            TRUE
-  #define LPC8xx_SERIAL_USE_UART1            FALSE
-  #define LPC8xx_SERIAL_USE_UART2            FALSE
-  #define LPC8xx_SERIAL_UART0_IRQ_PRIORITY   3
-  #define LPC8xx_SERIAL_UART1_IRQ_PRIORITY   3
-  #define LPC8xx_SERIAL_UART2_IRQ_PRIORITY   3
-
-  #define LPC8xx_SERIAL_U_PCLK              11059200
-  #define LPC8xx_SERIAL_UARTCLKDIV          !!Calculated!!
-  #define LPC8xx_SERIAL_UARTFRGMUL          !!Calculated!!
-  #define LPC8xx_SERIAL_UARTFRGDIV          !!Calculated!!
-*/
-
-/* change default baudrate to 9600 */
-#define SERIAL_DEFAULT_BITRATE              9600
-
-