Merge branch 'master' into coderkun_neo2

3 files changed, 214 insertions, 211 deletions

diff --git a/keyboards/chibios_test/stm32_f072_onekey/Makefile b/keyboards/chibios_test/stm32_f072_onekey/Makefile
index eae38c4b2..191c6bb66 100644
--- a/keyboards/chibios_test/stm32_f072_onekey/Makefile
+++ b/keyboards/chibios_test/stm32_f072_onekey/Makefile
@@ -1,41 +1,3 @@
-# project specific files
-SRC =	matrix.c \
-	    led.c
-
-## chip/board settings
-# the next two should match the directories in
-#  <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
-MCU_FAMILY = STM32
-MCU_SERIES = STM32F0xx
-# linker script to use
-# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
-#  or <this_dir>/ld/
-MCU_LDSCRIPT = STM32F072xB
-# startup code to use
-# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
-MCU_STARTUP = stm32f0xx
-# it should exist either in <chibios>/os/hal/boards/
-#  or <this_dir>/boards
-BOARD = ST_STM32F072B_DISCOVERY
-# Cortex version
-# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
-MCU  = cortex-m0
-# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
-ARMV = 6
-# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
-# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
-# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
-# a custom board definition that you plan to reuse).
-# If you're not setting it here, leave it commented out.
-# It is chip dependent, the correct number can be looked up here (page 175):
-# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
-# This also requires a patch to chibios:
-#   <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
-#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
-
-# Build Options
-#   comment out to disable the options.
-#
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../../Makefile
-endif
+endif
\ No newline at end of file
diff --git a/keyboards/chibios_test/stm32_f072_onekey/mcuconf.h b/keyboards/chibios_test/stm32_f072_onekey/mcuconf.h
index 3d877aaa2..faca3defd 100644
--- a/keyboards/chibios_test/stm32_f072_onekey/mcuconf.h
+++ b/keyboards/chibios_test/stm32_f072_onekey/mcuconf.h
@@ -1,171 +1,171 @@
-/*

-    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio

-

-    Licensed under the Apache License, Version 2.0 (the "License");

-    you may not use this file except in compliance with the License.

-    You may obtain a copy of the License at

-

-        http://www.apache.org/licenses/LICENSE-2.0

-

-    Unless required by applicable law or agreed to in writing, software

-    distributed under the License is distributed on an "AS IS" BASIS,

-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

-    See the License for the specific language governing permissions and

-    limitations under the License.

-*/

-

-#ifndef _MCUCONF_H_

-#define _MCUCONF_H_

-

-/*

- * STM32F0xx drivers configuration.

- * The following settings override the default settings present in

- * the various device driver implementation headers.

- * Note that the settings for each driver only have effect if the whole

- * driver is enabled in halconf.h.

- *

- * IRQ priorities:

- * 3...0       Lowest...Highest.

- *

- * DMA priorities:

- * 0...3        Lowest...Highest.

- */

-

-#define STM32F0xx_MCUCONF

-

-/*

- * HAL driver system settings.

- */

-#define STM32_NO_INIT                       FALSE

-#define STM32_PVD_ENABLE                    FALSE

-#define STM32_PLS                           STM32_PLS_LEV0

-#define STM32_HSI_ENABLED                   TRUE

-#define STM32_HSI14_ENABLED                 TRUE

-#define STM32_HSI48_ENABLED                 FALSE

-#define STM32_LSI_ENABLED                   TRUE

-#define STM32_HSE_ENABLED                   FALSE

-#define STM32_LSE_ENABLED                   FALSE

-#define STM32_SW                            STM32_SW_PLL

-#define STM32_PLLSRC                        STM32_PLLSRC_HSI_DIV2

-#define STM32_PREDIV_VALUE                  1

-#define STM32_PLLMUL_VALUE                  12

-#define STM32_HPRE                          STM32_HPRE_DIV1

-#define STM32_PPRE                          STM32_PPRE_DIV1

-#define STM32_ADCSW                         STM32_ADCSW_HSI14

-#define STM32_ADCPRE                        STM32_ADCPRE_DIV4

-#define STM32_MCOSEL                        STM32_MCOSEL_NOCLOCK

-#define STM32_ADCPRE                        STM32_ADCPRE_DIV4

-#define STM32_ADCSW                         STM32_ADCSW_HSI14

-#define STM32_USBSW                         STM32_USBSW_HSI48

-#define STM32_CECSW                         STM32_CECSW_HSI

-#define STM32_I2C1SW                        STM32_I2C1SW_HSI

-#define STM32_USART1SW                      STM32_USART1SW_PCLK

-#define STM32_RTCSEL                        STM32_RTCSEL_LSI

-

-/*

- * ADC driver system settings.

- */

-#define STM32_ADC_USE_ADC1                  FALSE

-#define STM32_ADC_ADC1_DMA_PRIORITY         2

-#define STM32_ADC_IRQ_PRIORITY              2

-#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY     2

-

-/*

- * EXT driver system settings.

- */

-#define STM32_EXT_EXTI0_1_IRQ_PRIORITY      3

-#define STM32_EXT_EXTI2_3_IRQ_PRIORITY      3

-#define STM32_EXT_EXTI4_15_IRQ_PRIORITY     3

-#define STM32_EXT_EXTI16_IRQ_PRIORITY       3

-#define STM32_EXT_EXTI17_IRQ_PRIORITY       3

-

-/*

- * GPT driver system settings.

- */

-#define STM32_GPT_USE_TIM1                  FALSE

-#define STM32_GPT_USE_TIM2                  FALSE

-#define STM32_GPT_USE_TIM3                  FALSE

-#define STM32_GPT_USE_TIM14                 FALSE

-#define STM32_GPT_TIM1_IRQ_PRIORITY         2

-#define STM32_GPT_TIM2_IRQ_PRIORITY         2

-#define STM32_GPT_TIM3_IRQ_PRIORITY         2

-#define STM32_GPT_TIM14_IRQ_PRIORITY        2

-

-/*

- * I2C driver system settings.

- */

-#define STM32_I2C_USE_I2C1                  FALSE

-#define STM32_I2C_USE_I2C2                  FALSE

-#define STM32_I2C_BUSY_TIMEOUT              50

-#define STM32_I2C_I2C1_IRQ_PRIORITY         3

-#define STM32_I2C_I2C2_IRQ_PRIORITY         3

-#define STM32_I2C_USE_DMA                   TRUE

-#define STM32_I2C_I2C1_DMA_PRIORITY         1

-#define STM32_I2C_I2C2_DMA_PRIORITY         1

-#define STM32_I2C_DMA_ERROR_HOOK(i2cp)      osalSysHalt("DMA failure")

-

-/*

- * ICU driver system settings.

- */

-#define STM32_ICU_USE_TIM1                  FALSE

-#define STM32_ICU_USE_TIM2                  FALSE

-#define STM32_ICU_USE_TIM3                  FALSE

-#define STM32_ICU_TIM1_IRQ_PRIORITY         3

-#define STM32_ICU_TIM2_IRQ_PRIORITY         3

-#define STM32_ICU_TIM3_IRQ_PRIORITY         3

-

-/*

- * PWM driver system settings.

- */

-#define STM32_PWM_USE_ADVANCED              FALSE

-#define STM32_PWM_USE_TIM1                  FALSE

-#define STM32_PWM_USE_TIM2                  FALSE

-#define STM32_PWM_USE_TIM3                  FALSE

-#define STM32_PWM_TIM1_IRQ_PRIORITY         3

-#define STM32_PWM_TIM2_IRQ_PRIORITY         3

-#define STM32_PWM_TIM3_IRQ_PRIORITY         3

-

-/*

- * SERIAL driver system settings.

- */

-#define STM32_SERIAL_USE_USART1             FALSE

-#define STM32_SERIAL_USE_USART2             FALSE

-#define STM32_SERIAL_USART1_PRIORITY        3

-#define STM32_SERIAL_USART2_PRIORITY        3

-

-/*

- * SPI driver system settings.

- */

-#define STM32_SPI_USE_SPI1                  FALSE

-#define STM32_SPI_USE_SPI2                  FALSE

-#define STM32_SPI_SPI1_DMA_PRIORITY         1

-#define STM32_SPI_SPI2_DMA_PRIORITY         1

-#define STM32_SPI_SPI1_IRQ_PRIORITY         2

-#define STM32_SPI_SPI2_IRQ_PRIORITY         2

-#define STM32_SPI_DMA_ERROR_HOOK(spip)      osalSysHalt("DMA failure")

-

-/*

- * ST driver system settings.

- */

-#define STM32_ST_IRQ_PRIORITY               2

-#define STM32_ST_USE_TIMER                  2

-

-/*

- * UART driver system settings.

- */

-#define STM32_UART_USE_USART1               FALSE

-#define STM32_UART_USE_USART2               FALSE

-#define STM32_UART_USART1_IRQ_PRIORITY      3

-#define STM32_UART_USART2_IRQ_PRIORITY      3

-#define STM32_UART_USART1_DMA_PRIORITY      0

-#define STM32_UART_USART2_DMA_PRIORITY      0

-#define STM32_UART_DMA_ERROR_HOOK(uartp)    osalSysHalt("DMA failure")

-

-/*

- * USB driver system settings.

- */

-#define STM32_USB_USE_USB1                  TRUE

-#define STM32_USB_LOW_POWER_ON_SUSPEND      FALSE

-#define STM32_USB_USB1_LP_IRQ_PRIORITY      3

-

-#endif /* _MCUCONF_H_ */

+/*
+    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#ifndef _MCUCONF_H_
+#define _MCUCONF_H_
+
+/*
+ * STM32F0xx drivers configuration.
+ * The following settings override the default settings present in
+ * the various device driver implementation headers.
+ * Note that the settings for each driver only have effect if the whole
+ * driver is enabled in halconf.h.
+ *
+ * IRQ priorities:
+ * 3...0       Lowest...Highest.
+ *
+ * DMA priorities:
+ * 0...3        Lowest...Highest.
+ */
+
+#define STM32F0xx_MCUCONF
+
+/*
+ * HAL driver system settings.
+ */
+#define STM32_NO_INIT                       FALSE
+#define STM32_PVD_ENABLE                    FALSE
+#define STM32_PLS                           STM32_PLS_LEV0
+#define STM32_HSI_ENABLED                   TRUE
+#define STM32_HSI14_ENABLED                 TRUE
+#define STM32_HSI48_ENABLED                 FALSE
+#define STM32_LSI_ENABLED                   TRUE
+#define STM32_HSE_ENABLED                   FALSE
+#define STM32_LSE_ENABLED                   FALSE
+#define STM32_SW                            STM32_SW_PLL
+#define STM32_PLLSRC                        STM32_PLLSRC_HSI_DIV2
+#define STM32_PREDIV_VALUE                  1
+#define STM32_PLLMUL_VALUE                  12
+#define STM32_HPRE                          STM32_HPRE_DIV1
+#define STM32_PPRE                          STM32_PPRE_DIV1
+#define STM32_ADCSW                         STM32_ADCSW_HSI14
+#define STM32_ADCPRE                        STM32_ADCPRE_DIV4
+#define STM32_MCOSEL                        STM32_MCOSEL_NOCLOCK
+#define STM32_ADCPRE                        STM32_ADCPRE_DIV4
+#define STM32_ADCSW                         STM32_ADCSW_HSI14
+#define STM32_USBSW                         STM32_USBSW_HSI48
+#define STM32_CECSW                         STM32_CECSW_HSI
+#define STM32_I2C1SW                        STM32_I2C1SW_HSI
+#define STM32_USART1SW                      STM32_USART1SW_PCLK
+#define STM32_RTCSEL                        STM32_RTCSEL_LSI
+
+/*
+ * ADC driver system settings.
+ */
+#define STM32_ADC_USE_ADC1                  FALSE
+#define STM32_ADC_ADC1_DMA_PRIORITY         2
+#define STM32_ADC_IRQ_PRIORITY              2
+#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY     2
+
+/*
+ * EXT driver system settings.
+ */
+#define STM32_EXT_EXTI0_1_IRQ_PRIORITY      3
+#define STM32_EXT_EXTI2_3_IRQ_PRIORITY      3
+#define STM32_EXT_EXTI4_15_IRQ_PRIORITY     3
+#define STM32_EXT_EXTI16_IRQ_PRIORITY       3
+#define STM32_EXT_EXTI17_IRQ_PRIORITY       3
+
+/*
+ * GPT driver system settings.
+ */
+#define STM32_GPT_USE_TIM1                  FALSE
+#define STM32_GPT_USE_TIM2                  FALSE
+#define STM32_GPT_USE_TIM3                  FALSE
+#define STM32_GPT_USE_TIM14                 FALSE
+#define STM32_GPT_TIM1_IRQ_PRIORITY         2
+#define STM32_GPT_TIM2_IRQ_PRIORITY         2
+#define STM32_GPT_TIM3_IRQ_PRIORITY         2
+#define STM32_GPT_TIM14_IRQ_PRIORITY        2
+
+/*
+ * I2C driver system settings.
+ */
+#define STM32_I2C_USE_I2C1                  FALSE
+#define STM32_I2C_USE_I2C2                  FALSE
+#define STM32_I2C_BUSY_TIMEOUT              50
+#define STM32_I2C_I2C1_IRQ_PRIORITY         3
+#define STM32_I2C_I2C2_IRQ_PRIORITY         3
+#define STM32_I2C_USE_DMA                   TRUE
+#define STM32_I2C_I2C1_DMA_PRIORITY         1
+#define STM32_I2C_I2C2_DMA_PRIORITY         1
+#define STM32_I2C_DMA_ERROR_HOOK(i2cp)      osalSysHalt("DMA failure")
+
+/*
+ * ICU driver system settings.
+ */
+#define STM32_ICU_USE_TIM1                  FALSE
+#define STM32_ICU_USE_TIM2                  FALSE
+#define STM32_ICU_USE_TIM3                  FALSE
+#define STM32_ICU_TIM1_IRQ_PRIORITY         3
+#define STM32_ICU_TIM2_IRQ_PRIORITY         3
+#define STM32_ICU_TIM3_IRQ_PRIORITY         3
+
+/*
+ * PWM driver system settings.
+ */
+#define STM32_PWM_USE_ADVANCED              FALSE
+#define STM32_PWM_USE_TIM1                  FALSE
+#define STM32_PWM_USE_TIM2                  FALSE
+#define STM32_PWM_USE_TIM3                  FALSE
+#define STM32_PWM_TIM1_IRQ_PRIORITY         3
+#define STM32_PWM_TIM2_IRQ_PRIORITY         3
+#define STM32_PWM_TIM3_IRQ_PRIORITY         3
+
+/*
+ * SERIAL driver system settings.
+ */
+#define STM32_SERIAL_USE_USART1             FALSE
+#define STM32_SERIAL_USE_USART2             FALSE
+#define STM32_SERIAL_USART1_PRIORITY        3
+#define STM32_SERIAL_USART2_PRIORITY        3
+
+/*
+ * SPI driver system settings.
+ */
+#define STM32_SPI_USE_SPI1                  FALSE
+#define STM32_SPI_USE_SPI2                  FALSE
+#define STM32_SPI_SPI1_DMA_PRIORITY         1
+#define STM32_SPI_SPI2_DMA_PRIORITY         1
+#define STM32_SPI_SPI1_IRQ_PRIORITY         2
+#define STM32_SPI_SPI2_IRQ_PRIORITY         2
+#define STM32_SPI_DMA_ERROR_HOOK(spip)      osalSysHalt("DMA failure")
+
+/*
+ * ST driver system settings.
+ */
+#define STM32_ST_IRQ_PRIORITY               2
+#define STM32_ST_USE_TIMER                  2
+
+/*
+ * UART driver system settings.
+ */
+#define STM32_UART_USE_USART1               FALSE
+#define STM32_UART_USE_USART2               FALSE
+#define STM32_UART_USART1_IRQ_PRIORITY      3
+#define STM32_UART_USART2_IRQ_PRIORITY      3
+#define STM32_UART_USART1_DMA_PRIORITY      0
+#define STM32_UART_USART2_DMA_PRIORITY      0
+#define STM32_UART_DMA_ERROR_HOOK(uartp)    osalSysHalt("DMA failure")
+
+/*
+ * USB driver system settings.
+ */
+#define STM32_USB_USE_USB1                  TRUE
+#define STM32_USB_LOW_POWER_ON_SUSPEND      FALSE
+#define STM32_USB_USB1_LP_IRQ_PRIORITY      3
+
+#endif /* _MCUCONF_H_ */
diff --git a/keyboards/chibios_test/stm32_f072_onekey/rules.mk b/keyboards/chibios_test/stm32_f072_onekey/rules.mk
new file mode 100644
index 000000000..eae38c4b2
--- /dev/null
+++ b/keyboards/chibios_test/stm32_f072_onekey/rules.mk
@@ -0,0 +1,41 @@
+# project specific files
+SRC =	matrix.c \
+	    led.c
+
+## chip/board settings
+# the next two should match the directories in
+#  <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
+MCU_FAMILY = STM32
+MCU_SERIES = STM32F0xx
+# linker script to use
+# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
+#  or <this_dir>/ld/
+MCU_LDSCRIPT = STM32F072xB
+# startup code to use
+# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
+MCU_STARTUP = stm32f0xx
+# it should exist either in <chibios>/os/hal/boards/
+#  or <this_dir>/boards
+BOARD = ST_STM32F072B_DISCOVERY
+# Cortex version
+# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
+MCU  = cortex-m0
+# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
+ARMV = 6
+# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
+# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
+# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
+# a custom board definition that you plan to reuse).
+# If you're not setting it here, leave it commented out.
+# It is chip dependent, the correct number can be looked up here (page 175):
+# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
+# This also requires a patch to chibios:
+#   <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
+#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
+
+# Build Options
+#   comment out to disable the options.
+#
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif