Merge branch 'master' into coderkun_neo2

2 files changed, 302 insertions, 302 deletions

diff --git a/keyboards/gh60/keymaps/robotmaxtron/Makefile b/keyboards/gh60/keymaps/robotmaxtron/Makefile
index 2e69aee29..c73cf1141 100644
--- a/keyboards/gh60/keymaps/robotmaxtron/Makefile
+++ b/keyboards/gh60/keymaps/robotmaxtron/Makefile
@@ -1,112 +1,112 @@
-#----------------------------------------------------------------------------

-# On command line:

-#

-# make all = Make software.

-#

-# make clean = Clean out built project files.

-#

-# make coff = Convert ELF to AVR COFF.

-#

-# make extcoff = Convert ELF to AVR Extended COFF.

-#

-# make program = Download the hex file to the device.

-#                Please customize your programmer settings(PROGRAM_CMD)

-#

-# make teensy = Download the hex file to the device, using teensy_loader_cli.

-#               (must have teensy_loader_cli installed).

-#

-# make dfu = Download the hex file to the device, using dfu-programmer (must

-#            have dfu-programmer installed).

-#

-# make flip = Download the hex file to the device, using Atmel FLIP (must

-#             have Atmel FLIP installed).

-#

-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer

-#               (must have dfu-programmer installed).

-#

-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP

-#                (must have Atmel FLIP installed).

-#

-# make debug = Start either simulavr or avarice as specified for debugging, 

-#              with avr-gdb or avr-insight as the front end for debugging.

-#

-# make filename.s = Just compile filename.c into the assembler code only.

-#

-# make filename.i = Create a preprocessed source file for use in submitting

-#                   bug reports to the GCC project.

-#

-# To rebuild project do "make clean" then "make all".

-#----------------------------------------------------------------------------

-

-# MCU name

-#MCU = at90usb1287

-MCU = atmega32u4

-

-# Processor frequency.

-#     This will define a symbol, F_CPU, in all source code files equal to the

-#     processor frequency in Hz. You can then use this symbol in your source code to

-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done

-#     automatically to create a 32-bit value in your source code.

-#

-#     This will be an integer division of F_USB below, as it is sourced by

-#     F_USB after it has run through any CPU prescalers. Note that this value

-#     does not *change* the processor frequency - it should merely be updated to

-#     reflect the processor speed set externally so that the code can use accurate

-#     software delays.

-F_CPU = 16000000

-

-

-#

-# LUFA specific

-#

-# Target architecture (see library "Board Types" documentation).

-ARCH = AVR8

-

-# Input clock frequency.

-#     This will define a symbol, F_USB, in all source code files equal to the

-#     input clock frequency (before any prescaling is performed) in Hz. This value may

-#     differ from F_CPU if prescaling is used on the latter, and is required as the

-#     raw input clock is fed directly to the PLL sections of the AVR for high speed

-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'

-#     at the end, this will be done automatically to create a 32-bit value in your

-#     source code.

-#

-#     If no clock division is performed on the input clock inside the AVR (via the

-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.

-F_USB = $(F_CPU)

-

-# Interrupt driven control endpoint task(+60)

-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

-

-

-# Boot Section Size in *bytes*

-#   Teensy halfKay   512

-#   Teensy++ halfKay 1024

-#   Atmel DFU loader 4096

-#   LUFA bootloader  4096

-#   USBaspLoader     2048

-OPT_DEFS += -DBOOTLOADER_SIZE=4096

-

-

-# Build Options

-#   comment out to disable the options.

-#

-BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000)

-MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700)

-EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450)

-# CONSOLE_ENABLE ?= yes		# Console for debug(+400)

-# COMMAND_ENABLE ?= yes		# Commands for debug and configuration

-KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key

-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE

-# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend

-NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work

-# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality

-# MIDI_ENABLE ?= YES		# MIDI controls

-# UNICODE_ENABLE ?= YES		# Unicode

-# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID

-RGBLIGHT_ENABLE ?= yes          # Enable RGB Underglow

-

-ifndef QUANTUM_DIR

-	include ../../../../Makefile

-endif

-

+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450)
+# CONSOLE_ENABLE ?= yes		# Console for debug(+400)
+# COMMAND_ENABLE ?= yes		# Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend
+NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality
+# MIDI_ENABLE ?= YES		# MIDI controls
+# UNICODE_ENABLE ?= YES		# Unicode
+# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE ?= yes          # Enable RGB Underglow
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
+
diff --git a/keyboards/gh60/keymaps/robotmaxtron/config.h b/keyboards/gh60/keymaps/robotmaxtron/config.h
index 8272875ed..6a29e6b8c 100644
--- a/keyboards/gh60/keymaps/robotmaxtron/config.h
+++ b/keyboards/gh60/keymaps/robotmaxtron/config.h
@@ -1,190 +1,190 @@
-/*

-Copyright 2012 Jun Wako <wakojun@gmail.com>

-

-This program is free software: you can redistribute it and/or modify

-it under the terms of the GNU General Public License as published by

-the Free Software Foundation, either version 2 of the License, or

-(at your option) any later version.

-

-This program is distributed in the hope that it will be useful,

-but WITHOUT ANY WARRANTY; without even the implied warranty of

-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the

-GNU General Public License for more details.

-

-You should have received a copy of the GNU General Public License

-along with this program. If not, see <http://www.gnu.org/licenses/>.

-*/

-

-#ifndef CONFIG_H

-#define CONFIG_H

-

-#include "config_common.h"

-

-/* USB Device descriptor parameter */

-#define VENDOR_ID    0xFEED

-#define PRODUCT_ID   0x6060

-#define DEVICE_VER   0x0001

-#define MANUFACTURER    geekhack

-#define PRODUCT         GH60

-#define DESCRIPTION     t.m.k. keyboard firmware for GH60

-

-/* key matrix size */

-#define MATRIX_ROWS 5

-#define MATRIX_COLS 14

-

-/*

- * Keyboard Matrix Assignments

- *

- * Change this to how you wired your keyboard

- * COLS: AVR pins used for columns, left to right

- * ROWS: AVR pins used for rows, top to bottom

- * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)

- *         ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)

- *

-*/

- #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }

-// Rev A

-// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 }

-// Rev B/C

-   #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 }

-#define UNUSED_PINS

-

-/* COL2ROW or ROW2COL */

-#define DIODE_DIRECTION COL2ROW

-

-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */

-#define DEBOUNCING_DELAY 5

-

-/* define if matrix has ghost (lacks anti-ghosting diodes) */

-//#define MATRIX_HAS_GHOST

-

-/* number of backlight levels */

-#define BACKLIGHT_LEVELS 3

-

-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */

-#define LOCKING_SUPPORT_ENABLE

-/* Locking resynchronize hack */

-#define LOCKING_RESYNC_ENABLE

-

-/*

- * Force NKRO

- *

- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved

- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the

- * makefile for this to work.)

- *

- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)

- * until the next keyboard reset.

- *

- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is

- * fully operational during normal computer usage.

- *

- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)

- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by

- * bootmagic, NKRO mode will always be enabled until it is toggled again during a

- * power-up.

- *

- */

-//#define FORCE_NKRO

-

-/*

- * Magic Key Options

- *

- * Magic keys are hotkey commands that allow control over firmware functions of

- * the keyboard. They are best used in combination with the HID Listen program,

- * found here: https://www.pjrc.com/teensy/hid_listen.html

- *

- * The options below allow the magic key functionality to be changed. This is

- * useful if your keyboard/keypad is missing keys and you want magic key support.

- *

- */

-

-/* key combination for magic key command */

-#define IS_COMMAND() ( \

-  keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \

-)

-

-/* control how magic key switches layers */

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false

-

-/* override magic key keymap */

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS

-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM

-//#define MAGIC_KEY_HELP1     H

-//#define MAGIC_KEY_HELP2     SLASH

-//#define MAGIC_KEY_DEBUG     D

-//#define MAGIC_KEY_DEBUG_MATRIX  X

-//#define MAGIC_KEY_DEBUG_KBD   K

-//#define MAGIC_KEY_DEBUG_MOUSE  M

-//#define MAGIC_KEY_VERSION    V

-//#define MAGIC_KEY_STATUS     S

-//#define MAGIC_KEY_CONSOLE    C

-//#define MAGIC_KEY_LAYER0_ALT1  ESC

-//#define MAGIC_KEY_LAYER0_ALT2  GRAVE

-//#define MAGIC_KEY_LAYER0     0

-//#define MAGIC_KEY_LAYER1     1

-//#define MAGIC_KEY_LAYER2     2

-//#define MAGIC_KEY_LAYER3     3

-//#define MAGIC_KEY_LAYER4     4

-//#define MAGIC_KEY_LAYER5     5

-//#define MAGIC_KEY_LAYER6     6

-//#define MAGIC_KEY_LAYER7     7

-//#define MAGIC_KEY_LAYER8     8

-//#define MAGIC_KEY_LAYER9     9

-//#define MAGIC_KEY_BOOTLOADER   PAUSE

-//#define MAGIC_KEY_LOCK      CAPS

-//#define MAGIC_KEY_EEPROM     E

-//#define MAGIC_KEY_NKRO      N

-//#define MAGIC_KEY_SLEEP_LED   Z

-

-/*

- * Feature disable options

- * These options are also useful to firmware size reduction.

- */

-

-/* disable debug print */

-//#define NO_DEBUG

-

-/* disable print */

-//#define NO_PRINT

-

-/* disable action features */

-//#define NO_ACTION_LAYER

-//#define NO_ACTION_TAPPING

-//#define NO_ACTION_ONESHOT

-//#define NO_ACTION_MACRO

-//#define NO_ACTION_FUNCTION

-

-/*

- * RGB Underglow

- * These settings are for the F4 by default:

- * 

- *

- * #define ws2812_PORTREG  PORTF

- * #define ws2812_DDRREG   DDRF

- * #define ws2812_pin PF4

- * #define RGBLED_NUM 14     // Number of LEDs

- * #define RGBLIGHT_HUE_STEP 10

- * #define RGBLIGHT_SAT_STEP 17

- * #define RGBLIGHT_VAL_STEP 17

- *

- * The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects. 

- * To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations. 

- * For details, please check this keymap. keyboard/planck/keymaps/yang/keymap.c

-*/

-

-/* Deprecated code below

-#define ws2812_PORTREG  PORTF 

-#define ws2812_DDRREG   DDRF

-#define ws2812_pin PF4

-*/ 

-#define RGB_DI_PIN F4

-#define RGBLIGHT_TIMER

-#define RGBLED_NUM 8         // Number of LEDs

-#define RGBLIGHT_HUE_STEP 8

-#define RGBLIGHT_SAT_STEP 8

-#define RGBLIGHT_VAL_STEP 8

-#endif

+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID    0xFEED
+#define PRODUCT_ID   0x6060
+#define DEVICE_VER   0x0001
+#define MANUFACTURER    geekhack
+#define PRODUCT         GH60
+#define DESCRIPTION     t.m.k. keyboard firmware for GH60
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 14
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *         ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+ #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }
+// Rev A
+// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 }
+// Rev B/C
+   #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+  keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1     H
+//#define MAGIC_KEY_HELP2     SLASH
+//#define MAGIC_KEY_DEBUG     D
+//#define MAGIC_KEY_DEBUG_MATRIX  X
+//#define MAGIC_KEY_DEBUG_KBD   K
+//#define MAGIC_KEY_DEBUG_MOUSE  M
+//#define MAGIC_KEY_VERSION    V
+//#define MAGIC_KEY_STATUS     S
+//#define MAGIC_KEY_CONSOLE    C
+//#define MAGIC_KEY_LAYER0_ALT1  ESC
+//#define MAGIC_KEY_LAYER0_ALT2  GRAVE
+//#define MAGIC_KEY_LAYER0     0
+//#define MAGIC_KEY_LAYER1     1
+//#define MAGIC_KEY_LAYER2     2
+//#define MAGIC_KEY_LAYER3     3
+//#define MAGIC_KEY_LAYER4     4
+//#define MAGIC_KEY_LAYER5     5
+//#define MAGIC_KEY_LAYER6     6
+//#define MAGIC_KEY_LAYER7     7
+//#define MAGIC_KEY_LAYER8     8
+//#define MAGIC_KEY_LAYER9     9
+//#define MAGIC_KEY_BOOTLOADER   PAUSE
+//#define MAGIC_KEY_LOCK      CAPS
+//#define MAGIC_KEY_EEPROM     E
+//#define MAGIC_KEY_NKRO      N
+//#define MAGIC_KEY_SLEEP_LED   Z
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+/*
+ * RGB Underglow
+ * These settings are for the F4 by default:
+ * 
+ *
+ * #define ws2812_PORTREG  PORTF
+ * #define ws2812_DDRREG   DDRF
+ * #define ws2812_pin PF4
+ * #define RGBLED_NUM 14     // Number of LEDs
+ * #define RGBLIGHT_HUE_STEP 10
+ * #define RGBLIGHT_SAT_STEP 17
+ * #define RGBLIGHT_VAL_STEP 17
+ *
+ * The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects. 
+ * To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations. 
+ * For details, please check this keymap. keyboard/planck/keymaps/yang/keymap.c
+*/
+
+/* Deprecated code below
+#define ws2812_PORTREG  PORTF 
+#define ws2812_DDRREG   DDRF
+#define ws2812_pin PF4
+*/ 
+#define RGB_DI_PIN F4
+#define RGBLIGHT_TIMER
+#define RGBLED_NUM 8         // Number of LEDs
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
+#endif