Merge remote-tracking branch 'refs/remotes/qmk/master'

1 files changed, 81 insertions, 0 deletions

diff --git a/keyboards/handwired/atreus50/rules.mk b/keyboards/handwired/atreus50/rules.mk
new file mode 100644
index 000000000..7770ea2a2
--- /dev/null
+++ b/keyboards/handwired/atreus50/rules.mk
@@ -0,0 +1,81 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no         # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+NKRO_ENABLE ?= no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no            # MIDI controls
+AUDIO_ENABLE ?= no           # Audio output on port C6
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE ?= no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
+
+avrdude: build
+	ls /dev/tty* > /tmp/1; \
+	echo "Reset your Pro Micro now"; \
+	while [[ -z $$USB ]]; do \
+	  sleep 1; \
+	  ls /dev/tty* > /tmp/2; \
+	  USB=`diff /tmp/1 /tmp/2 | grep -o '/dev/tty.*'`; \
+	done; \
+	avrdude -p $(MCU) -c avr109 -P $$USB -U flash:w:$(BUILD_DIR)/$(TARGET).hex
+
+.PHONY: avrdude