Merge branch 'master' into coderkun_neo2

19 files changed, 748 insertions, 365 deletions

diff --git a/keyboards/handwired/CMD60/Makefile b/keyboards/handwired/CMD60/Makefile
index 711759917..191c6bb66 100644
--- a/keyboards/handwired/CMD60/Makefile
+++ b/keyboards/handwired/CMD60/Makefile
@@ -1,73 +1,3 @@
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes        # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= no            # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE ?= no            # MIDI controls
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= no           # Audio output on port C6
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../../Makefile
-endif
-
-
+endif
\ No newline at end of file
diff --git a/keyboards/handwired/CMD60/rules.mk b/keyboards/handwired/CMD60/rules.mk
new file mode 100644
index 000000000..711759917
--- /dev/null
+++ b/keyboards/handwired/CMD60/rules.mk
@@ -0,0 +1,73 @@
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes        # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
+
+
diff --git a/keyboards/handwired/Makefile b/keyboards/handwired/Makefile
index 57493a47c..4e2a6f00f 100644
--- a/keyboards/handwired/Makefile
+++ b/keyboards/handwired/Makefile
@@ -1,3 +1,3 @@
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../Makefile
 endif
\ No newline at end of file
diff --git a/keyboards/handwired/fivethirteen/Makefile b/keyboards/handwired/fivethirteen/Makefile
index 711759917..191c6bb66 100644
--- a/keyboards/handwired/fivethirteen/Makefile
+++ b/keyboards/handwired/fivethirteen/Makefile
@@ -1,73 +1,3 @@
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes        # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= no            # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE ?= no            # MIDI controls
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= no           # Audio output on port C6
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../../Makefile
-endif
-
-
+endif
\ No newline at end of file
diff --git a/keyboards/handwired/fivethirteen/rules.mk b/keyboards/handwired/fivethirteen/rules.mk
new file mode 100644
index 000000000..711759917
--- /dev/null
+++ b/keyboards/handwired/fivethirteen/rules.mk
@@ -0,0 +1,73 @@
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes        # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
+
+
diff --git a/keyboards/handwired/minorca/Makefile b/keyboards/handwired/minorca/Makefile
index 155c1f9a2..191c6bb66 100644
--- a/keyboards/handwired/minorca/Makefile
+++ b/keyboards/handwired/minorca/Makefile
@@ -1,71 +1,3 @@
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= no         # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
-NKRO_ENABLE ?= yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality
-MIDI_ENABLE ?= no            # MIDI controls
-AUDIO_ENABLE ?= no           # Audio output on port C6
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE ?= yes       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../../Makefile
 endif
\ No newline at end of file
diff --git a/keyboards/handwired/minorca/rules.mk b/keyboards/handwired/minorca/rules.mk
new file mode 100644
index 000000000..c51371a78
--- /dev/null
+++ b/keyboards/handwired/minorca/rules.mk
@@ -0,0 +1,67 @@
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no         # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+NKRO_ENABLE ?= yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no            # MIDI controls
+AUDIO_ENABLE ?= no           # Audio output on port C6
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE ?= yes       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
\ No newline at end of file
diff --git a/keyboards/handwired/onekey/Makefile b/keyboards/handwired/onekey/Makefile
index c6d10856a..191c6bb66 100644
--- a/keyboards/handwired/onekey/Makefile
+++ b/keyboards/handwired/onekey/Makefile
@@ -1,65 +1,3 @@
-
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= no	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes	# Console for debug(+400)
-COMMAND_ENABLE ?= yes    # Commands for debug and configuration
-#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../../Makefile
 endif
\ No newline at end of file
diff --git a/keyboards/handwired/onekey/rules.mk b/keyboards/handwired/onekey/rules.mk
new file mode 100644
index 000000000..c6d10856a
--- /dev/null
+++ b/keyboards/handwired/onekey/rules.mk
@@ -0,0 +1,65 @@
+
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= no	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes	# Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/handwired/retro_refit/Makefile b/keyboards/handwired/retro_refit/Makefile
new file mode 100644
index 000000000..191c6bb66
--- /dev/null
+++ b/keyboards/handwired/retro_refit/Makefile
@@ -0,0 +1,3 @@
+ifndef MAKEFILE_INCLUDED
+	include ../../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/handwired/retro_refit/config.h b/keyboards/handwired/retro_refit/config.h
new file mode 100644
index 000000000..f2194e550
--- /dev/null
+++ b/keyboards/handwired/retro_refit/config.h
@@ -0,0 +1,123 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    Nobody
+#define PRODUCT         retro_refit
+#define DESCRIPTION     Retro Refit
+
+/* key matrix size */
+#define MATRIX_ROWS 11
+#define MATRIX_COLS 8
+
+// See note in retro_refit.h for an explanation of how this matrix is wired up
+#define MATRIX_ROW_PINS { D4, D7, B4, B5, B6, F7, F6, F5, F4, F1, F0 }
+#define MATRIX_COL_PINS { B0, B1, B2, B3, D2, D3, C7, D5 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* define if matrix has ghost */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 0
+
+/* Set 0 if debouncing isn't needed */
+#define DEBOUNCING_DELAY 5
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+
+/* Force NKRO Mode - If forced on, must be disabled via magic key (default = LShift+RShift+N) */
+#define FORCE_NKRO
+
+/*
+ * Magic key options
+ * These options allow the magic key functionality to be changed. This is useful
+ * if your keyboard/keypad is missing keys and you want magic key support.
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* remap magic keys */
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+#define MAGIC_KEY_LOCK             BSLS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboards/handwired/retro_refit/keymaps/default/keymap.c b/keyboards/handwired/retro_refit/keymaps/default/keymap.c
new file mode 100644
index 000000000..405402d5e
--- /dev/null
+++ b/keyboards/handwired/retro_refit/keymaps/default/keymap.c
@@ -0,0 +1,33 @@
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+// this is the style you want to emulate.
+
+#include "retro_refit.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[0] =
+	KEYMAP( ESC,    F1,   F2,   F3,   F4,   F5,   F6,   F7,   F8,  F9,  F10, NLCK, SLCK, PSCR, PAUS, \
+			GRV,     1,    2,    3,    4,    5,    6,    7,    8,   9,    0, MINS,  EQL, BSPC, HOME, \
+			TAB,     Q,    W,    E,    R,    T,    Y,    U,    I,   O,    P, LBRC, RBRC,       PGUP, \
+			BSLS,    A,    S,    D,    F,    G,    H,    J,    K,   L, SCLN, QUOT,        ENT, PGDN, \
+			LSFT,          Z,    X,    C,    V,    B,    N,    M, COMM, DOT, SLSH, RSFT,   UP,  END, \
+			LCTL, LGUI, LALT,        SPC,                               INS,  DEL, LEFT, DOWN, RGHT),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+      switch(id) {
+        case 0:
+          if (record->event.pressed) {
+            register_code(KC_RSFT);
+          } else {
+            unregister_code(KC_RSFT);
+          }
+        break;
+      }
+    return MACRO_NONE;
+};
diff --git a/keyboards/handwired/retro_refit/readme.md b/keyboards/handwired/retro_refit/readme.md
new file mode 100644
index 000000000..9f10edf9f
--- /dev/null
+++ b/keyboards/handwired/retro_refit/readme.md
@@ -0,0 +1,60 @@
+retro_refit keyboard firmware
+======================
+
+## Keyboard Info
+
+The retro refit keyboard used a Teensy to replace the original controller on a 386 "laptop".
+
+http://imgur.com/a/08Fyj
+
+This keyboard uses a KEYMAP macro that is a great example of using a non-standard row-column matrix. The keyboard in question had 11 rows and 8 columns, but the rows were not all horizontal, and the columns were not all vertical. For example, row 2 contained "Print Screen", "N", "M", ",", ".", "/", "Right Shift", and"Left Alt". Column 0 contained "F6", "7", "O", "'", "Q", "D", "B", "Left Alt", "Up Arrow", and "Down Arrow".
+
+The macro makes programming the keys easier and in a more straight-forward manner because it realigns the keys into a 6x15 sensible keyboard layout instead of the obtuse 11x8 matrix. Each Kxy corrisponds to a key in row x column y.
+
+```
+#define KEYMAP( \
+	K77, K05, K04, K03, K02, K01, K00, KA7, KA6, KA5, KA4, KA3, KA2, K11, K94, \
+	K27, K76, K75, K74, K73, K72, K71, K70, K67, K66, K65, K64, K63, K62, KA1, \
+	K61, K60, K57, K56, K55, K54, K53, K52, K51, K50, K47, K46, K45,      K97, \
+	K43, K42, K41, K40, K37, K36, K35, K34, K33, K32, K31, K30,      K44, K87, \
+	K26,      K24, K23, K22, K21, K20, K17, K16, K15, K14, K13, K12, KA0, K91, \
+	K10, K06, K25,                K07,                K86, K85, K95, K90, K93  \
+) { \
+{	KC_##K00,	KC_##K01,	KC_##K02,	KC_##K03,	KC_##K04,	KC_##K05,	KC_##K06,	KC_##K07,	}, \
+{	KC_##K10,	KC_##K11,	KC_##K12,	KC_##K13,	KC_##K14,	KC_##K15,	KC_##K16,	KC_##K17,	}, \
+{	KC_##K20,	KC_##K21,	KC_##K22,	KC_##K23,	KC_##K24,	KC_##K25,	KC_##K26,	KC_##K27,	}, \
+{	KC_##K30,	KC_##K31,	KC_##K32,	KC_##K33,	KC_##K34,	KC_##K35,	KC_##K36,	KC_##K37,	}, \
+{	KC_##K40,	KC_##K41,	KC_##K42,	KC_##K43,	KC_##K44,	KC_##K45,	KC_##K46,	KC_##K47,	}, \
+{	KC_##K50,	KC_##K51,	KC_##K52,	KC_##K53,	KC_##K54,	KC_##K55,	KC_##K56,	KC_##K57,	}, \
+{	KC_##K60,	KC_##K61,	KC_##K62,	KC_##K63,	KC_##K64,	KC_##K65,	KC_##K66,	KC_##K67,	}, \
+{	KC_##K70,	KC_##K71,	KC_##K72,	KC_##K73,	KC_##K74,	KC_##K75,	KC_##K76,	KC_##K77,	}, \
+{	KC_NO,		KC_NO,		KC_NO,		KC_NO,		KC_NO,		KC_##K85,	KC_##K86,	KC_##K87,	}, \
+{	KC_##K90,	KC_##K91,	KC_NO,		KC_##K93,	KC_##K94,	KC_##K95,	KC_NO,		KC_##K97,	}, \
+{	KC_##KA0,	KC_##KA1,	KC_##KA2,	KC_##KA3,	KC_##KA4,	KC_##KA5,	KC_##KA6,	KC_##KA7,	}  \
+}
+```
+
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent readme.md](/readme.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboards/retro_refit folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+To build with the default keymap, simply run `make default`.
+
+### Other Keymaps
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` and see keymap document (you can find in top readme.md) and existent keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with a keymap like this:
+
+```
+$ make [default|jack|<name>]
+```
+
+Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
\ No newline at end of file
diff --git a/keyboards/handwired/retro_refit/retro_refit.c b/keyboards/handwired/retro_refit/retro_refit.c
new file mode 100644
index 000000000..3d610eba3
--- /dev/null
+++ b/keyboards/handwired/retro_refit/retro_refit.c
@@ -0,0 +1,47 @@
+#include "retro_refit.h"
+#include "led.h"
+
+void matrix_init_kb(void) {
+    // put your keyboard start-up code here
+    // runs once when the firmware starts up
+
+    // Disable status LED on KB, enable status LED on Teensy (KB_STATUS = !TEENSY_STATUS)
+    DDRD |= (1<<6);
+    PORTD |= (1<<6);
+
+    matrix_init_user();
+};
+
+void led_set_kb(uint8_t usb_led) {
+    // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+    if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+        // output low
+        DDRD |= (1<<0);
+        PORTD &= ~(1<<0);
+    } else {
+        // Hi-Z
+        DDRD &= ~(1<<0);
+        PORTD &= ~(1<<0);
+    }
+    if (usb_led & (1<<USB_LED_NUM_LOCK)) {
+        // output low
+        DDRD |= (1<<1);
+        PORTD &= ~(1<<1);
+    } else {
+        // Hi-Z
+        DDRD &= ~(1<<1);
+        PORTD &= ~(1<<1);
+    }
+    if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {
+        // output low
+        DDRC |= (1<<6);
+        PORTC &= ~(1<<6);
+    } else {
+        // Hi-Z
+        DDRC &= ~(1<<6);
+        PORTC &= ~(1<<6);
+    }
+
+    led_set_user(usb_led);
+};
\ No newline at end of file
diff --git a/keyboards/handwired/retro_refit/retro_refit.h b/keyboards/handwired/retro_refit/retro_refit.h
new file mode 100644
index 000000000..109acdc39
--- /dev/null
+++ b/keyboards/handwired/retro_refit/retro_refit.h
@@ -0,0 +1,38 @@
+#ifndef RETRO_REFIT_H
+#define RETRO_REFIT_H
+
+#include "quantum.h"
+
+// This macro is an example of using a non-standard row-column matrix. The 
+// keyboard in question had 11 rows and 8 columns, but the rows were not all 
+// horizontal, and the columns were not all vertical. For example, row 2 
+// contained "Print Screen", "N", "M", ",", ".", "/", "Right Shift", and
+// "Left Alt". Column 0 contained "F6", "7", "O", "'", "Q", "D", "B", 
+// "Left Alt", "Up Arrow", and "Down Arrow".
+//
+// The macro makes programming the keys easier and in a more straight-forward
+// manner because it realigns the keys into a 6x15 sensible keyboard layout 
+// instead of the obtuse 11x8 matrix.
+
+#define KEYMAP( \
+	K77, K05, K04, K03, K02, K01, K00, KA7, KA6, KA5, KA4, KA3, KA2, K11, K94, \
+	K27, K76, K75, K74, K73, K72, K71, K70, K67, K66, K65, K64, K63, K62, KA1, \
+	K61, K60, K57, K56, K55, K54, K53, K52, K51, K50, K47, K46, K45,      K97, \
+	K43, K42, K41, K40, K37, K36, K35, K34, K33, K32, K31, K30,      K44, K87, \
+	K26,      K24, K23, K22, K21, K20, K17, K16, K15, K14, K13, K12, KA0, K91, \
+	K10, K06, K25,                K07,                K86, K85, K95, K90, K93  \
+) { \
+{	KC_##K00,	KC_##K01,	KC_##K02,	KC_##K03,	KC_##K04,	KC_##K05,	KC_##K06,	KC_##K07,	}, \
+{	KC_##K10,	KC_##K11,	KC_##K12,	KC_##K13,	KC_##K14,	KC_##K15,	KC_##K16,	KC_##K17,	}, \
+{	KC_##K20,	KC_##K21,	KC_##K22,	KC_##K23,	KC_##K24,	KC_##K25,	KC_##K26,	KC_##K27,	}, \
+{	KC_##K30,	KC_##K31,	KC_##K32,	KC_##K33,	KC_##K34,	KC_##K35,	KC_##K36,	KC_##K37,	}, \
+{	KC_##K40,	KC_##K41,	KC_##K42,	KC_##K43,	KC_##K44,	KC_##K45,	KC_##K46,	KC_##K47,	}, \
+{	KC_##K50,	KC_##K51,	KC_##K52,	KC_##K53,	KC_##K54,	KC_##K55,	KC_##K56,	KC_##K57,	}, \
+{	KC_##K60,	KC_##K61,	KC_##K62,	KC_##K63,	KC_##K64,	KC_##K65,	KC_##K66,	KC_##K67,	}, \
+{	KC_##K70,	KC_##K71,	KC_##K72,	KC_##K73,	KC_##K74,	KC_##K75,	KC_##K76,	KC_##K77,	}, \
+{	KC_NO,		KC_NO,		KC_NO,		KC_NO,		KC_NO,		KC_##K85,	KC_##K86,	KC_##K87,	}, \
+{	KC_##K90,	KC_##K91,	KC_NO,		KC_##K93,	KC_##K94,	KC_##K95,	KC_NO,		KC_##K97,	}, \
+{	KC_##KA0,	KC_##KA1,	KC_##KA2,	KC_##KA3,	KC_##KA4,	KC_##KA5,	KC_##KA6,	KC_##KA7,	} \
+}
+
+#endif
\ No newline at end of file
diff --git a/keyboards/handwired/retro_refit/rules.mk b/keyboards/handwired/retro_refit/rules.mk
new file mode 100644
index 000000000..10fbfa5c9
--- /dev/null
+++ b/keyboards/handwired/retro_refit/rules.mk
@@ -0,0 +1,68 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= yes		# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes		# Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes		# Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes		# Console for debug(+400)
+COMMAND_ENABLE ?= yes		# Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes	# Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+# SLEEP_LED_ENABLE ?= yes	# Breathing sleep LED during USB suspend
+NKRO_ENABLE ?= yes			# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+# BACKLIGHT_ENABLE ?= yes	# Enable keyboard backlight functionality
+# MIDI_ENABLE ?= YES			# MIDI controls
+# UNICODE_ENABLE ?= YES		# Unicode
+# BLUETOOTH_ENABLE ?= yes	# Enable Bluetooth with the Adafruit EZ-Key HID
diff --git a/keyboards/handwired/rules.mk b/keyboards/handwired/rules.mk
new file mode 100644
index 000000000..e69de29bb
--- /dev/null
+++ b/keyboards/handwired/rules.mk
diff --git a/keyboards/handwired/traveller/Makefile b/keyboards/handwired/traveller/Makefile
index 12a4b71f4..191c6bb66 100644
--- a/keyboards/handwired/traveller/Makefile
+++ b/keyboards/handwired/traveller/Makefile
@@ -1,89 +1,3 @@
-
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-# for avr upload
-USB ?= /dev/cu.usbmodem1421
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-
-ifdef TEENSY2
-    OPT_DEFS += -DATREUS_TEENSY2
-    ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
-else
-    OPT_DEFS += -DATREUS_ASTAR
-    OPT_DEFS += -DCATERINA_BOOTLOADER
-    ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
-                            avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
-endif
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# MCU name
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= no        # Console for debug(+400)
-COMMAND_ENABLE ?= no        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= no            # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE ?= no            # MIDI controls
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= no           # Audio output on port C6
-RGBLIGHT_ENABLE = yes
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
 	include ../../../Makefile
-endif
-
-upload: build
-	$(ATREUS_UPLOAD_COMMAND)
-
+endif
\ No newline at end of file
diff --git a/keyboards/handwired/traveller/rules.mk b/keyboards/handwired/traveller/rules.mk
new file mode 100644
index 000000000..12a4b71f4
--- /dev/null
+++ b/keyboards/handwired/traveller/rules.mk
@@ -0,0 +1,89 @@
+
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+# for avr upload
+USB ?= /dev/cu.usbmodem1421
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+ifdef TEENSY2
+    OPT_DEFS += -DATREUS_TEENSY2
+    ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
+else
+    OPT_DEFS += -DATREUS_ASTAR
+    OPT_DEFS += -DCATERINA_BOOTLOADER
+    ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
+                            avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
+endif
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# MCU name
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no        # Console for debug(+400)
+COMMAND_ENABLE ?= no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+RGBLIGHT_ENABLE = yes
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
+
+upload: build
+	$(ATREUS_UPLOAD_COMMAND)
+