diff options
| author | Callum Oakley <c.oakley108@gmail.com> | 2016-09-01 17:55:00 +0100 |
|---|---|---|
| committer | Callum Oakley <c.oakley108@gmail.com> | 2016-09-01 17:55:00 +0100 |
| commit | 9c3193f22555119eb15f63f5ae5efe45e6d7358c (patch) | |
| tree | a0dcfb3ed442c12a66b444c4c579711660c30657 /keyboards/handwired | |
| parent | 993d72b11fca8d50296570dc85e9354f8045c4a6 (diff) | |
| parent | e28d151a8a1d458f3c18897c6095decc17b0c3a1 (diff) | |
| download | firmware-9c3193f22555119eb15f63f5ae5efe45e6d7358c.tar.gz firmware-9c3193f22555119eb15f63f5ae5efe45e6d7358c.tar.bz2 firmware-9c3193f22555119eb15f63f5ae5efe45e6d7358c.zip | |
Merge remote-tracking branch 'upstream/master'
Diffstat (limited to 'keyboards/handwired')
28 files changed, 747 insertions, 296 deletions
diff --git a/keyboards/handwired/CMD60/Makefile b/keyboards/handwired/CMD60/Makefile index 711759917..191c6bb66 100644 --- a/keyboards/handwired/CMD60/Makefile +++ b/keyboards/handwired/CMD60/Makefile @@ -1,73 +1,3 @@ - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif - - +endif
\ No newline at end of file diff --git a/keyboards/handwired/CMD60/rules.mk b/keyboards/handwired/CMD60/rules.mk new file mode 100644 index 000000000..711759917 --- /dev/null +++ b/keyboards/handwired/CMD60/rules.mk @@ -0,0 +1,73 @@ + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + + diff --git a/keyboards/handwired/Makefile b/keyboards/handwired/Makefile index 57493a47c..4e2a6f00f 100644 --- a/keyboards/handwired/Makefile +++ b/keyboards/handwired/Makefile @@ -1,3 +1,3 @@ -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/handwired/fivethirteen/Makefile b/keyboards/handwired/fivethirteen/Makefile index 711759917..191c6bb66 100644 --- a/keyboards/handwired/fivethirteen/Makefile +++ b/keyboards/handwired/fivethirteen/Makefile @@ -1,73 +1,3 @@ - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif - - +endif
\ No newline at end of file diff --git a/keyboards/handwired/fivethirteen/rules.mk b/keyboards/handwired/fivethirteen/rules.mk new file mode 100644 index 000000000..711759917 --- /dev/null +++ b/keyboards/handwired/fivethirteen/rules.mk @@ -0,0 +1,73 @@ + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + + diff --git a/keyboards/handwired/minorca/Makefile b/keyboards/handwired/minorca/Makefile new file mode 100644 index 000000000..191c6bb66 --- /dev/null +++ b/keyboards/handwired/minorca/Makefile @@ -0,0 +1,3 @@ +ifndef MAKEFILE_INCLUDED + include ../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/handwired/minorca/config.h b/keyboards/handwired/minorca/config.h new file mode 100644 index 000000000..4cdafcbd2 --- /dev/null +++ b/keyboards/handwired/minorca/config.h @@ -0,0 +1,80 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6660 +#define DEVICE_VER 0x0001 +#define MANUFACTURER ME +#define PRODUCT MinOrca +#define DESCRIPTION Tiny Whale + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* MinOrca PCB default pin-out */ +#define MATRIX_COL_PINS { D4, D6, D7, B4, B5, B6, F7, F6, F5, F4, F1, F0 } +#define MATRIX_ROW_PINS { B0, B1, B2, B3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/handwired/minorca/keymaps/default/Makefile b/keyboards/handwired/minorca/keymaps/default/Makefile new file mode 100644 index 000000000..a573488a5 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/default/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../../Makefile +endif diff --git a/keyboards/handwired/minorca/keymaps/default/config.h b/keyboards/handwired/minorca/keymaps/default/config.h new file mode 100644 index 000000000..bf40376c1 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/default/config.h @@ -0,0 +1,12 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +/* bootmagic salt key */ +#define BOOTMAGIC_KEY_SALT KC_ESC + +/* skip bootmagic and eeconfig */ +#define BOOTMAGIC_KEY_SKIP KC_SPACE + +#endif diff --git a/keyboards/handwired/minorca/keymaps/default/keymap.c b/keyboards/handwired/minorca/keymaps/default/keymap.c new file mode 100644 index 000000000..a55d578e4 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/default/keymap.c @@ -0,0 +1,44 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "minorca.h" +#include "action_layer.h" +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = { /* Base */ + {KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC }, + {KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, XXXXXXX, KC_ENT }, + {KC_LCTRL,XXXXXXX, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_QUOT, KC_FN1, KC_FN0 }, + {KC_NO, XXXXXXX, KC_NO, KC_LALT, KC_SPC, XXXXXXX, XXXXXXX, KC_SPC, XXXXXXX, KC_DOT, KC_SLSH, KC_NO } + }, + [1] = { /* First */ + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DELT }, + {KC_TAB, KC_MPRV, KC_MPLY, KC_MNXT, KC_PGUP, KC_HOME, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, XXXXXXX, KC_LGUI }, + {KC_LCTRL,XXXXXXX, KC_Z, KC_X, KC_C, KC_PGDN, KC_END, KC_L, KC_SCLN, KC_UP, KC_FN1, KC_FN0 }, + {KC_NO, XXXXXXX, KC_NO, KC_LALT, _______, XXXXXXX, XXXXXXX, _______, XXXXXXX, KC_DOWN, KC_RIGHT,KC_NO } + }, + [2] = { /* Second */ + {KC_ESC, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DELT }, + {KC_TAB, KC_MUTE, KC_VOLD, KC_VOLU, KC_TILD, KC_PIPE, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, XXXXXXX, KC_ENT }, + {KC_CAPS, XXXXXXX, KC_LSFT, KC_RSFT, KC_PAUSE,KC_F10, KC_F11, KC_F12, KC_NO, KC_UP, KC_FN1, KC_FN0 }, + {KC_NO, XXXXXXX, KC_NO, KC_LALT, _______, XXXXXXX, XXXXXXX, _______, XXXXXXX, KC_DOWN, KC_RIGHT,KC_NO } + }, +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_MOMENTARY(1), // to First overlay + [1] = ACTION_LAYER_MOMENTARY(2), // to Second overlay + +};
\ No newline at end of file diff --git a/keyboards/handwired/minorca/keymaps/default/readme.md b/keyboards/handwired/minorca/keymaps/default/readme.md new file mode 100644 index 000000000..6ed31f82b --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/default/readme.md @@ -0,0 +1,5 @@ +# The Default Minorca Layout + +Copied from https://github.com/pancinteractive/qmk_firmware/blob/master/keyboard/minorca_mkV/keymaps/default/keymap.c + +It looks incomplete.
\ No newline at end of file diff --git a/keyboards/handwired/minorca/keymaps/readme.md b/keyboards/handwired/minorca/keymaps/readme.md new file mode 100644 index 000000000..058923ba2 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/readme.md @@ -0,0 +1,23 @@ +# How to add your own keymap + +Folders can be named however you'd like (will be approved upon merging), or should follow the format with a preceding `_`: + + _[ISO 3166-1 alpha-2 code*]_[layout variant]_[layout name/author] + +\* See full list: https://en.wikipedia.org/wiki/ISO_3166-1#Officially_assigned_code_elements + +and contain the following files: + +* `keymap.c` +* `readme.md` *recommended* +* `config.h` *optional*, found automatically when compiling +* `Makefile` *optional*, found automatically when compling + +When adding your keymap to this list, keep it organised alphabetically (select list, edit->sort lines), and use this format: + + * **folder_name** description + +# List of Minorca keymaps + +* **default** default Minorca layout +* **rgb** layout with WS2812b control diff --git a/keyboards/handwired/minorca/keymaps/rgb/Makefile b/keyboards/handwired/minorca/keymaps/rgb/Makefile new file mode 100644 index 000000000..2b2af1335 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../../Makefile +endif diff --git a/keyboards/handwired/minorca/keymaps/rgb/config.h b/keyboards/handwired/minorca/keymaps/rgb/config.h new file mode 100644 index 000000000..deaac2e26 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/config.h @@ -0,0 +1,20 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +/* bootmagic salt key */ +#define BOOTMAGIC_KEY_SALT KC_ESC + +/* skip bootmagic and eeconfig */ +#define BOOTMAGIC_KEY_SKIP KC_SPACE + +/* ws2812 RGB LED */ +#define RGB_DI_PIN D5 +#define RGBLIGHT_TIMER +#define RGBLED_NUM 13 // Number of LEDs +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + +#endif diff --git a/keyboards/handwired/minorca/keymaps/rgb/example.jpg b/keyboards/handwired/minorca/keymaps/rgb/example.jpg Binary files differnew file mode 100644 index 000000000..a04c8d37d --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/example.jpg diff --git a/keyboards/handwired/minorca/keymaps/rgb/keymap.c b/keyboards/handwired/minorca/keymaps/rgb/keymap.c new file mode 100644 index 000000000..9002afbb8 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/keymap.c @@ -0,0 +1,65 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "minorca.h" +#include "action_layer.h" +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _LOWER 1 +#define _RAISE 2 +#define _TB 3 + +// Macro name shortcuts +#define QWERTY M(_QWERTY) +#define LOWER M(_LOWER) +#define RAISE M(_RAISE) + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +[_QWERTY] = { /* Qwerty */ + {KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC}, + {FUNC(0), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, XXXXXXX, KC_QUOT}, + {KC_LSFT, XXXXXXX, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, FUNC(1)}, + {KC_LCTL, XXXXXXX, KC_LGUI, KC_LALT, FUNC(2), XXXXXXX, XXXXXXX, FUNC(3), XXXXXXX, KC_RALT, KC_APP, KC_RCTL} +}, + +[_RAISE] = { + {S(KC_GRV), S(KC_1), S(KC_2), S(KC_3), S(KC_4), S(KC_5), S(KC_6), S(KC_7), S(KC_8), S(KC_9), S(KC_0), KC_BSPC}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_PAUSE, KC_TRNS, KC_TRNS, KC_TRNS, S(KC_MINS), S(KC_EQL), S(KC_LBRC), XXXXXXX, S(KC_BSLS)}, + {KC_TRNS, XXXXXXX, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_ENT}, + {KC_TRNS, XXXXXXX, KC_TRNS, KC_TRNS, KC_TRNS, XXXXXXX, XXXXXXX, KC_TRNS, XXXXXXX, KC_MNXT, KC_MUTE, KC_MPLY} +}, + +[_LOWER] = { + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DELETE}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MINS, KC_EQL, KC_LBRC, XXXXXXX, KC_BSLS}, + {KC_TRNS, XXXXXXX, KC_F11, KC_F12, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_PGUP, KC_ENT}, + {KC_TRNS, XXXXXXX, KC_TRNS, KC_TRNS, KC_TRNS, XXXXXXX, XXXXXXX, KC_TRNS, XXXXXXX, KC_HOME, KC_PGDN, KC_END} +}, + +[_TB] = { /* Tab */ + {KC_ESC, KC_CALC, KC_WHOM, KC_MAIL, KC_MYCM, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PSCR, KC_TRNS}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, XXXXXXX, KC_TRNS}, + {KC_TRNS, XXXXXXX, RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUD, RGB_SAI, RGB_SAD, RGB_VAI, RGB_VAD, KC_UP, KC_ENT}, + {BL_STEP, XXXXXXX, KC_TRNS, KC_TRNS, KC_TRNS, XXXXXXX, XXXXXXX, KC_TRNS, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT} +} +}; + + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_TAP_KEY(_TB, KC_TAB), + [1] = ACTION_MODS_TAP_KEY(MOD_RSFT, KC_ENT), + [2] = ACTION_LAYER_TAP_KEY(_RAISE, KC_SPC), + [3] = ACTION_LAYER_TAP_KEY(_LOWER, KC_SPC), +}; diff --git a/keyboards/handwired/minorca/keymaps/rgb/readme.md b/keyboards/handwired/minorca/keymaps/rgb/readme.md new file mode 100644 index 000000000..f50dfa546 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/readme.md @@ -0,0 +1,25 @@ +#RGB backlight for MinOrca + + + +Example of adding WS2812b LEDs to a MinOrca. + +http://www.40percent.club/2016/08/tiny-whale.html + +The keymap is a work in progress. The RGB functions are accessed by holding down the TAB key. + +* Tab + Z Toggle on/off +* Tab + X Mode +* Tab + C Hue+ +* Tab + V Hue- +* Tab + B Saturation+ +* Tab + N Saturation- +* Tab + M Brightness+ +* Tab + , Brightness- + +Example wiring: + +WS2812 data pin is connected to D5 + + + diff --git a/keyboards/handwired/minorca/keymaps/rgb/wiring1.jpg b/keyboards/handwired/minorca/keymaps/rgb/wiring1.jpg Binary files differnew file mode 100644 index 000000000..7dcbe80c5 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/wiring1.jpg diff --git a/keyboards/handwired/minorca/keymaps/rgb/wiring2.jpg b/keyboards/handwired/minorca/keymaps/rgb/wiring2.jpg Binary files differnew file mode 100644 index 000000000..fd91d3e1c --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/wiring2.jpg diff --git a/keyboards/handwired/minorca/minorca.c b/keyboards/handwired/minorca/minorca.c new file mode 100644 index 000000000..24e72c2a5 --- /dev/null +++ b/keyboards/handwired/minorca/minorca.c @@ -0,0 +1,6 @@ +#include "minorca.h" + +void matrix_init_kb(void) { + + matrix_init_user(); +}
\ No newline at end of file diff --git a/keyboards/handwired/minorca/minorca.h b/keyboards/handwired/minorca/minorca.h new file mode 100644 index 000000000..158e5b4c5 --- /dev/null +++ b/keyboards/handwired/minorca/minorca.h @@ -0,0 +1,6 @@ +#ifndef MINORCA_H +#define MINORCA_H + +#include "quantum.h" + +#endif diff --git a/keyboards/handwired/minorca/readme.md b/keyboards/handwired/minorca/readme.md new file mode 100644 index 000000000..93c767954 --- /dev/null +++ b/keyboards/handwired/minorca/readme.md @@ -0,0 +1,33 @@ +minorca keyboard firmware +====================== +Handwired 40% keyboard + +http://www.panc.co/blog/minorcasebright-information-page + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/planck folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use `make dfu` to program your PCB once you hit the reset button. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +``` +$ make KEYMAP=[default|jack|<name>] +``` +Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. + +### Notable forks (which some of the keymap files are from) +- [Shane's Fork](https://github.com/shanecelis/tmk_keyboard/tree/master/keyboard/planck) +- [Pierre's Fork](https://github.com/pcarrier/tmk_keyboard/blob/pcarrier/planck/keyboard/gh60/keymap_planck.c) +- [Nathan's Fork](https://github.com/nathanrosspowell/tmk_keyboard/tree/planck-jack/keyboard/planck) +- [Matthew's Fork](https://github.com/pepers/tmk_keyboard/tree/master/keyboard/planck_grid) diff --git a/keyboards/handwired/minorca/rules.mk b/keyboards/handwired/minorca/rules.mk new file mode 100644 index 000000000..c51371a78 --- /dev/null +++ b/keyboards/handwired/minorca/rules.mk @@ -0,0 +1,67 @@ +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
\ No newline at end of file diff --git a/keyboards/handwired/onekey/Makefile b/keyboards/handwired/onekey/Makefile index c6d10856a..191c6bb66 100644 --- a/keyboards/handwired/onekey/Makefile +++ b/keyboards/handwired/onekey/Makefile @@ -1,65 +1,3 @@ - - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile endif
\ No newline at end of file diff --git a/keyboards/handwired/onekey/rules.mk b/keyboards/handwired/onekey/rules.mk new file mode 100644 index 000000000..c6d10856a --- /dev/null +++ b/keyboards/handwired/onekey/rules.mk @@ -0,0 +1,65 @@ + + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA + +ifndef QUANTUM_DIR + include ../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/handwired/rules.mk b/keyboards/handwired/rules.mk new file mode 100644 index 000000000..e69de29bb --- /dev/null +++ b/keyboards/handwired/rules.mk diff --git a/keyboards/handwired/traveller/Makefile b/keyboards/handwired/traveller/Makefile index 12a4b71f4..191c6bb66 100644 --- a/keyboards/handwired/traveller/Makefile +++ b/keyboards/handwired/traveller/Makefile @@ -1,89 +1,3 @@ - -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# for avr upload -USB ?= /dev/cu.usbmodem1421 -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - - -ifdef TEENSY2 - OPT_DEFS += -DATREUS_TEENSY2 - ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex -else - OPT_DEFS += -DATREUS_ASTAR - OPT_DEFS += -DCATERINA_BOOTLOADER - ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) -endif -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# MCU name - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 -RGBLIGHT_ENABLE = yes - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../../Makefile -endif - -upload: build - $(ATREUS_UPLOAD_COMMAND) - +endif
\ No newline at end of file diff --git a/keyboards/handwired/traveller/rules.mk b/keyboards/handwired/traveller/rules.mk new file mode 100644 index 000000000..12a4b71f4 --- /dev/null +++ b/keyboards/handwired/traveller/rules.mk @@ -0,0 +1,89 @@ + +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# for avr upload +USB ?= /dev/cu.usbmodem1421 +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +ifdef TEENSY2 + OPT_DEFS += -DATREUS_TEENSY2 + ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex +else + OPT_DEFS += -DATREUS_ASTAR + OPT_DEFS += -DCATERINA_BOOTLOADER + ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ + avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) +endif +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# MCU name + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 +RGBLIGHT_ENABLE = yes + +ifndef QUANTUM_DIR + include ../../../Makefile +endif + +upload: build + $(ATREUS_UPLOAD_COMMAND) + |
