Fix Planck and Preonic builds (#5658)

* Planck: Copy contents of Planck rules.mk to each revision

* Planck: Delete Planck rules.mk

* Planck: Concatenate duplicate rules

Concatenate rules that are set and then overridden into one setting.

* Preonic: Copy contents of Preonic rules.mk to each revision

* Preonic: Delete Preonic rules.mk

* Preonic: Concatenate duplicate rules

Concatenate rules that are set and then overridden into one setting.

* Planck: Delete non-specific Bootloader settings from revs. 1 and 2

Deleted BOOTLOADER setting code block, as the checks were only valid for revs. 3-5 and the Planck Light.

Neither Planck rev1 or rev2 set the bootloader via rules.mk, so there's no setting of BOOTLOADER in their rules.mk files.

* Preonic: Fix BOOTLOADER settings code blocks

* Preonic: delete extra blank lines from rules.mk files

* Preonic: delete AVR-type hardware config blocks from rev3

* Update Planck and Preonic readme files

- update Hardware Supported
- update/add Install Examples
- update Docs paragraph

* Enable Bootmagic Lite where it is disabled

Enabled Bootmagic Lite for:

- Planck Light
- Planck revs. 1-5
- Preonic revs. 1 and 2

* Remove `planck_grid` from LAYOUTS rule for all Planck revisions

Community has landed on `ortho_4x12`, which is already set; `planck_grid` is redundant.

5 files changed, 164 insertions, 89 deletions

diff --git a/keyboards/preonic/readme.md b/keyboards/preonic/readme.md
index 5b3c0ec58..85adf635d 100644
--- a/keyboards/preonic/readme.md
+++ b/keyboards/preonic/readme.md
@@ -6,11 +6,16 @@ Preonic
 A compact 50% (12x5) ortholinear keyboard kit made and sold by OLKB and Massdrop. [More info on qmk.fm](http://qmk.fm/preonic/)
 
 Keyboard Maintainer: [Jack Humbert](https://github.com/jackhumbert)  
-Hardware Supported: Preonic PCB rev1, Teensy 2.0  
+Hardware Supported: Preonic PCB rev1, rev2, rev3  
 Hardware Availability: [OLKB.com](https://olkb.com/preonic/), [Massdrop](https://www.massdrop.com/buy/preonic-mechanical-keyboard?mode=guest_open)
 
 Make example for this keyboard (after setting up your build environment):
 
-    make preonic:default
+    make preonic/rev2:default
 
-See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information.
\ No newline at end of file
+Install examples:
+
+    make preonic/rev2:default:dfu         # For Preonic rev1 or rev2
+    make preonic/rev3:default:dfu-util    # For Preonic rev3
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
diff --git a/keyboards/preonic/rev1/rules.mk b/keyboards/preonic/rev1/rules.mk
index e69de29bb..b0d44db82 100644
--- a/keyboards/preonic/rev1/rules.mk
+++ b/keyboards/preonic/rev1/rules.mk
@@ -0,0 +1,67 @@
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded 
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = atmel-dfu
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes         # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = yes           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
+API_SYSEX_ENABLE = no
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+LAYOUTS = ortho_5x12
diff --git a/keyboards/preonic/rev2/rules.mk b/keyboards/preonic/rev2/rules.mk
index e69de29bb..748979c79 100644
--- a/keyboards/preonic/rev2/rules.mk
+++ b/keyboards/preonic/rev2/rules.mk
@@ -0,0 +1,67 @@
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded 
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = qmk-dfu
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes         # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = yes           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
+API_SYSEX_ENABLE = no
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+LAYOUTS = ortho_5x12
diff --git a/keyboards/preonic/rev3/rules.mk b/keyboards/preonic/rev3/rules.mk
index 0c171b2fb..39e69872c 100644
--- a/keyboards/preonic/rev3/rules.mk
+++ b/keyboards/preonic/rev3/rules.mk
@@ -1,24 +1,34 @@
 # project specific files
 SRC = matrix.c
-LAYOUTS += ortho_5x12
 
 # Cortex version
 MCU  = STM32F303
 
 # Build Options
-#   comment out to disable the options.
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
 #
-BACKLIGHT_ENABLE = no
-BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration
+BOOTMAGIC_ENABLE = yes      # Virtual DIP switch configuration(+1000)
 ## (Note that for BOOTMAGIC on Teensy LC you have to use a custom .ld script.)
-MOUSEKEY_ENABLE = yes # Mouse keys
-EXTRAKEY_ENABLE = yes # Audio control and System control
-CONSOLE_ENABLE = yes  # Console for debug
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-NKRO_ENABLE = yes     # USB Nkey Rollover
+MOUSEKEY_ENABLE = yes      # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes         # Console for debug(+400)
+COMMAND_ENABLE = yes       # Commands for debug and configuration
+NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = yes           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
+API_SYSEX_ENABLE = no
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+#SLEEP_LED_ENABLE = yes
+
 CUSTOM_MATRIX = yes # Custom matrix file
-AUDIO_ENABLE = yes
-RGBLIGHT_ENABLE = no
 # SERIAL_LINK_ENABLE = yes
 ENCODER_ENABLE = yes
+
+LAYOUTS = ortho_5x12
diff --git a/keyboards/preonic/rules.mk b/keyboards/preonic/rules.mk
deleted file mode 100644
index e646f2493..000000000
--- a/keyboards/preonic/rules.mk
+++ /dev/null
@@ -1,74 +0,0 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded 
-#     automatically (+60). See bootloader.mk for all options.
-ifeq ($(strip $(KEYBOARD)), preonic/rev1)
-    BOOTLOADER = atmel-dfu
-endif
-ifeq ($(strip $(KEYBOARD)), preonic/rev2)
-    BOOTLOADER = qmk-dfu
-endif
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = yes         # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
-MIDI_ENABLE = no            # MIDI controls
-AUDIO_ENABLE = yes           # Audio output on port C6
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
-API_SYSEX_ENABLE = no
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
-
-LAYOUTS = ortho_5x12