aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--keyboards/db/db63/README.md21
-rw-r--r--keyboards/db/db63/config.h42
-rw-r--r--keyboards/db/db63/db63.c17
-rw-r--r--keyboards/db/db63/db63.h49
-rw-r--r--keyboards/db/db63/info.json18
-rw-r--r--keyboards/db/db63/keymaps/default/keymap.c60
-rw-r--r--keyboards/db/db63/rules.mk24
-rw-r--r--keyboards/db/db63/usbconfig.h383
8 files changed, 614 insertions, 0 deletions
diff --git a/keyboards/db/db63/README.md b/keyboards/db/db63/README.md
new file mode 100644
index 000000000..e886bed0a
--- /dev/null
+++ b/keyboards/db/db63/README.md
@@ -0,0 +1,21 @@
+# DB63
+
+A 65% keyboard hotswap with RGB that runs ps2avrgb natively, with USB C, RGB underglow and backlight.
+
+* Keyboard Maintainer: QMK Community
+* Hardware Supported: DB63 (ATmega32A)
+* [Keyboard layout](http://www.keyboard-layout-editor.com/#/gists/dadea703fc8bfc87dc7c480de9f3ef38)
+
+Make example for this keyboard (after setting up your build environment):
+
+ make db/db63:default
+
+Flashing example for this keyboard ([after setting up the bootloadHID flashing environment](https://docs.qmk.fm/#/flashing_bootloadhid))
+
+ make db/db63:default:flash
+
+**Reset Key**: Hold down the key located at *K00*, commonly programmed as *Escape* while plugging in the keyboard. (*All backlight LEDs will flash which indicate the board is in bootloader mode.*)
+
+**Tips**: Another trick to enable the board in reset mode is using BootMapper Client->Options->Set Bootloader. (*This is only available for the first time, before flashing QMK Firmware.*)
+
+See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
diff --git a/keyboards/db/db63/config.h b/keyboards/db/db63/config.h
new file mode 100644
index 000000000..468e0f8a9
--- /dev/null
+++ b/keyboards/db/db63/config.h
@@ -0,0 +1,42 @@
+/*
+Copyright 2020 Hung DO <hungdohuy@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#define VENDOR_ID 0xFAAD
+#define PRODUCT_ID 0x422D
+#define DEVICE_VER 0x0200
+// You can edit those at usbconfig.h about line 250. These values will
+// unforunatly be ignored so far
+#define MANUFACTURER HNB
+#define PRODUCT DB63v1 Hotswap
+
+#define MATRIX_ROWS 6
+#define MATRIX_COLS 14
+
+#define MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5 }
+#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 }
+#define UNUSED_PINS
+
+#define RGBLED_NUM 18
+#define RGBLIGHT_ANIMATIONS
+
+#define NO_UART 1
+
+#define BACKLIGHT_PIN D4
+#define BACKLIGHT_LEVELS 3
+
diff --git a/keyboards/db/db63/db63.c b/keyboards/db/db63/db63.c
new file mode 100644
index 000000000..62ebb2cc6
--- /dev/null
+++ b/keyboards/db/db63/db63.c
@@ -0,0 +1,17 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "db63.h"
diff --git a/keyboards/db/db63/db63.h b/keyboards/db/db63/db63.h
new file mode 100644
index 000000000..d9a4d1e6d
--- /dev/null
+++ b/keyboards/db/db63/db63.h
@@ -0,0 +1,49 @@
+/*
+Copyright 2020 Hung DO <hungdohuy@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "quantum.h"
+#define _x_ KC_NO
+
+/* This a shortcut to help you visually see your layout.
+ *
+ * The first section contains all of the arguments representing the physical
+ * layout of the board and position of the keys.
+ *
+ * The second converts the arguments into a two-dimensional array which
+ * represents the switch matrix.
+ * MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5 }
+ * MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2 }
+ *
+ */
+
+#define LAYOUT( \
+ k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, \
+ k10 , k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, \
+ k20 , k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \
+ k30 , k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, \
+ k40 , k41 , k42 , k43 , k44, k45, k46, k47 , k48 \
+) { \
+ { k00, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_, _x_ }, \
+ { _x_, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d }, \
+ { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k46 }, \
+ { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3c, k3a, k47, _x_ }, \
+ { k40, k41, k42, k43, k45, _x_, _x_, k44, _x_, _x_, _x_, k3b, _x_, k48 } \
+}
+
diff --git a/keyboards/db/db63/info.json b/keyboards/db/db63/info.json
new file mode 100644
index 000000000..b8ec10539
--- /dev/null
+++ b/keyboards/db/db63/info.json
@@ -0,0 +1,18 @@
+{
+ "keyboard_name": "db63",
+ "url": "http://www.keyboard-layout-editor.com/#/gists/dadea703fc8bfc87dc7c480de9f3ef38",
+ "maintainer": "QMK Community",
+ "width": 15,
+ "height": 5,
+ "layouts": {
+ "LAYOUT": {
+ "layout": [
+ { "label": "~", "x": 0, "y": 0 }, { "label": "!", "x": 1, "y": 0 }, { "label": "@", "x": 2, "y": 0 }, { "label": "#", "x": 3, "y": 0 }, { "label": "$", "x": 4, "y": 0 }, { "label": "%", "x": 5, "y": 0 }, { "label": "^", "x": 6, "y": 0 }, { "label": "&", "x": 7, "y": 0 }, { "label": "*", "x": 8, "y": 0 }, { "label": "(", "x": 9, "y": 0 }, { "label": ")", "x": 10, "y": 0 }, { "label": "_", "x": 11, "y": 0 }, { "label": "+", "x": 12, "y": 0 }, { "label": "Backspace", "x": 13, "y": 0, "w": 2 },
+ { "label": "Tab", "x": 0, "y": 1, "w": 1.5 }, { "label": "Q", "x": 1.5, "y": 1 }, { "label": "W", "x": 2.5, "y": 1 }, { "label": "E", "x": 3.5, "y": 1 }, { "label": "R", "x": 4.5, "y": 1 }, { "label": "T", "x": 5.5, "y": 1 }, { "label": "Y", "x": 6.5, "y": 1 }, { "label": "U", "x": 7.5, "y": 1 }, { "label": "I", "x": 8.5, "y": 1 }, { "label": "O", "x": 9.5, "y": 1 }, { "label": "P", "x": 10.5, "y": 1 }, { "label": "{", "x": 11.5, "y": 1 }, { "label": "}", "x": 12.5, "y": 1 }, { "label": "|", "x": 13.5, "y": 1, "w": 1.5 },
+ { "label": "Fn3", "x": 0, "y": 2, "w": 1.75 }, { "label": "A", "x": 1.75, "y": 2 }, { "label": "S", "x": 2.75, "y": 2 }, { "label": "D", "x": 3.75, "y": 2 }, { "label": "F", "x": 4.75, "y": 2 }, { "label": "G", "x": 5.75, "y": 2 }, { "label": "H", "x": 6.75, "y": 2 }, { "label": "J", "x": 7.75, "y": 2 }, { "label": "K", "x": 8.75, "y": 2 }, { "label": "L", "x": 9.75, "y": 2 }, { "label": ":", "x": 10.75, "y": 2 }, { "label": "\"", "x": 11.75, "y": 2 }, { "label": "Enter", "x": 12.75, "y": 2, "w": 2.25 },
+ { "label": "Shift", "x": 0, "y": 3, "w": 2.25 }, { "label": "Z", "x": 2.25, "y": 3 }, { "label": "X", "x": 3.25, "y": 3 }, { "label": "C", "x": 4.25, "y": 3 }, { "label": "V", "x": 5.25, "y": 3 }, { "label": "B", "x": 6.25, "y": 3 }, { "label": "N", "x": 7.25, "y": 3 }, { "label": "M", "x": 8.25, "y": 3 }, { "label": "<", "x": 9.25, "y": 3 }, { "label": ">", "x": 10.25, "y": 3 }, { "label": "Shift", "x": 11.25, "y": 3, "w": 1.75 }, { "label": "Up", "x": 13, "y": 3 }, { "label": "Fn2", "x": 14, "y": 3 },
+ { "label": "Ctrl", "x": 0, "y": 4, "w": 1.25 }, { "label": "Alt", "x": 1.25, "y": 4, "w": 1.25 }, { "label": "Win", "x": 2.5, "y": 4, "w": 1.25 }, { "label": "Space", "x": 3.75, "y": 4, "w": 6.25 }, { "label": "?", "x": 10, "y": 4 }, { "label": "Fn1", "x": 11, "y": 4 }, { "label": "Left", "x": 12, "y": 4 }, { "label": "Down", "x": 13, "y": 4 }, { "label": "Right", "x": 14, "y": 4 }
+ ]
+ }
+ }
+} \ No newline at end of file
diff --git a/keyboards/db/db63/keymaps/default/keymap.c b/keyboards/db/db63/keymaps/default/keymap.c
new file mode 100644
index 000000000..800ff960b
--- /dev/null
+++ b/keyboards/db/db63/keymaps/default/keymap.c
@@ -0,0 +1,60 @@
+/*
+Copyright 2020 Hung DO <hungdohuy@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ [0] = LAYOUT(
+ KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC,
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
+ MO(3), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT,
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, MO(2),
+ KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_SLSH, MO(1), KC_LEFT, KC_DOWN, KC_RGHT
+ ),
+ [1] = LAYOUT(
+ KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC,
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
+ KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, _______,
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, XXXXXXX,
+ KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, _______, MO(1), KC_LEFT, KC_DOWN, KC_RGHT
+ ),
+ [2] = LAYOUT(
+ KC_GESC, RGB_M_P, RGB_M_B, RGB_M_R, RGB_M_SW, RGB_M_SN, RGB_M_K, RGB_M_X, RGB_M_G, RGB_M_T, RGB_TOG, RGB_VAD, RGB_VAI, KC_BSPC,
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
+ XXXXXXX, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, _______,
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, MO(2),
+ KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, _______, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT
+ ),
+ [3] = LAYOUT(
+ _______, _______, _______, _______, _______, _______, _______, _______, BL_STEP, BL_BRTG, BL_TOGG, BL_DEC, BL_INC, _______,
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS,
+ MO(3), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, RESET,
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, KC_UP, XXXXXXX,
+ KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, _______, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT
+ ),
+};
+
+bool led_update_user(led_t led_state) {
+ if (led_state.caps_lock) {
+ rgblight_sethsv(HSV_CYAN);
+ writePinHigh(D1);
+ } else {
+ rgblight_sethsv(HSV_GREEN);
+ writePinLow(D1);
+ }
+ return false;
+}
diff --git a/keyboards/db/db63/rules.mk b/keyboards/db/db63/rules.mk
new file mode 100644
index 000000000..84eace5ed
--- /dev/null
+++ b/keyboards/db/db63/rules.mk
@@ -0,0 +1,24 @@
+# MCU name
+MCU = atmega32a
+
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = bootloadHID
+
+# build options
+BOOTMAGIC_ENABLE = no
+MOUSEKEY_ENABLE = yes
+EXTRAKEY_ENABLE = yes
+CONSOLE_ENABLE = no
+COMMAND_ENABLE = yes
+BACKLIGHT_ENABLE = yes
+RGBLIGHT_ENABLE = yes
+WS2812_DRIVER = i2c
+
+OPT_DEFS = -DDEBUG_LEVEL=0
diff --git a/keyboards/db/db63/usbconfig.h b/keyboards/db/db63/usbconfig.h
new file mode 100644
index 000000000..0dfe8b3ba
--- /dev/null
+++ b/keyboards/db/db63/usbconfig.h
@@ -0,0 +1,383 @@
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
+ */
+
+#pragma once
+
+#include "config.h"
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT 3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT 2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC 0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT 4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER 3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT 0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE 0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_IS_SELF_POWERED 0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE 1
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ 0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL 0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE 0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS 0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF 1
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ * in YL, TCNT0
+ * sts timer0Snapshot, YL
+ * endm
+ * #endif
+ * #define USB_SOF_HOOK myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING 0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC 0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF)
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME 'H', 'N', 'B'
+#define USB_CFG_VENDOR_NAME_LEN 3
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME 'D', 'B', '6', '3', 'H', 'S'
+#define USB_CFG_DEVICE_NAME_LEN 6
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS 0
+#define USB_CFG_DEVICE_SUBCLASS 0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS 3 /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ * you want RAM pointers.
+ * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ * in static memory is in RAM, not in flash memory.
+ * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ * the driver must know the descriptor's length. The descriptor itself is
+ * found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ * char usbDescriptorDevice[];
+ * char usbDescriptorConfiguration[];
+ * char usbDescriptorHidReport[];
+ * char usbDescriptorString0[];
+ * int usbDescriptorStringVendor[];
+ * int usbDescriptorStringDevice[];
+ * int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ * USB_CFG_DESCR_PROPS_DEVICE
+ * USB_CFG_DESCR_PROPS_CONFIGURATION
+ * USB_CFG_DESCR_PROPS_STRINGS
+ * USB_CFG_DESCR_PROPS_STRING_0
+ * USB_CFG_DESCR_PROPS_STRING_VENDOR
+ * USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ * USB_CFG_DESCR_PROPS_HID
+ * USB_CFG_DESCR_PROPS_HID_REPORT
+ * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int serialNumberDescriptor[] = {
+ * USB_STRING_DESCRIPTOR_HEADER(6),
+ * 'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE 0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
+#define USB_CFG_DESCR_PROPS_STRINGS 0
+#define USB_CFG_DESCR_PROPS_STRING_0 0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
+#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID 0
+#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID_REPORT 0
+#define USB_CFG_DESCR_PROPS_UNKNOWN 0
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG MCUCR */
+/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR 0 */
+/* #define USB_INTR_ENABLE GIMSK */
+/* #define USB_INTR_ENABLE_BIT INT0 */
+/* #define USB_INTR_PENDING GIFR */
+/* #define USB_INTR_PENDING_BIT INTF0 */
+/* #define USB_INTR_VECTOR INT0_vect */
+
+/* Set INT1 for D- falling edge to count SOF */
+/* #define USB_INTR_CFG EICRA */
+#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
+/* #define USB_INTR_CFG_CLR 0 */
+/* #define USB_INTR_ENABLE EIMSK */
+#define USB_INTR_ENABLE_BIT INT1
+/* #define USB_INTR_PENDING EIFR */
+#define USB_INTR_PENDING_BIT INTF1
+#define USB_INTR_VECTOR INT1_vect