diff options
Diffstat (limited to 'keyboard/atomic/Makefile')
| -rw-r--r-- | keyboard/atomic/Makefile | 73 |
1 files changed, 0 insertions, 73 deletions
diff --git a/keyboard/atomic/Makefile b/keyboard/atomic/Makefile deleted file mode 100644 index 08e9205cb..000000000 --- a/keyboard/atomic/Makefile +++ /dev/null @@ -1,73 +0,0 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR - include ../../Makefile -endif
\ No newline at end of file |