aboutsummaryrefslogtreecommitdiffstats
path: root/keyboards/atreus/Makefile
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/atreus/Makefile')
-rw-r--r--keyboards/atreus/Makefile89
1 files changed, 2 insertions, 87 deletions
diff --git a/keyboards/atreus/Makefile b/keyboards/atreus/Makefile
index 5894d231f..4e2a6f00f 100644
--- a/keyboards/atreus/Makefile
+++ b/keyboards/atreus/Makefile
@@ -1,88 +1,3 @@
-
-
-ifdef TEENSY2
- OPT_DEFS += -DATREUS_TEENSY2
- ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
-else
- OPT_DEFS += -DATREUS_ASTAR
- OPT_DEFS += -DCATERINA_BOOTLOADER
- ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
- avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
-endif
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes # Console for debug(+400)
-COMMAND_ENABLE ?= yes # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
-NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA
-# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
-# MIDI_ENABLE ?= YES # MIDI controls
-UNICODE_ENABLE ?= YES # Unicode
-# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
-
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
include ../../Makefile
-endif
-
-USB ?= /dev/cu.usbmodem1411
-
-upload: build
- $(ATREUS_UPLOAD_COMMAND)
-
+endif \ No newline at end of file