aboutsummaryrefslogtreecommitdiffstats
path: root/keyboards/ergodash/rules.mk
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/ergodash/rules.mk')
-rw-r--r--keyboards/ergodash/rules.mk41
1 files changed, 4 insertions, 37 deletions
diff --git a/keyboards/ergodash/rules.mk b/keyboards/ergodash/rules.mk
index e25346dac..8be059d96 100644
--- a/keyboards/ergodash/rules.mk
+++ b/keyboards/ergodash/rules.mk
@@ -1,52 +1,21 @@
-SRC += matrix.c \
- i2c.c \
- split_util.c \
- serial.c \
- ssd1306.c
-
# MCU name
-#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
F_CPU = 16000000
-#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina
# Build Options
@@ -57,19 +26,17 @@ BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
+COMMAND_ENABLE = no # Commands for debug and configuration
NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = no # Audio output on port C6
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
-SUBPROJECT_rev1 = yes
-USE_I2C = yes
+RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-CUSTOM_MATRIX = yes
+SPLIT_KEYBOARD = yes # Enables split keyboard support
-DEFAULT_FOLDER = ergodash/rev2
+DEFAULT_FOLDER = ergodash/rev1