aboutsummaryrefslogtreecommitdiffstats
path: root/keyboards/kbdfans
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/kbdfans')
-rw-r--r--keyboards/kbdfans/kbd19x/rules.mk51
-rw-r--r--keyboards/kbdfans/kbd4x/rules.mk51
-rw-r--r--keyboards/kbdfans/kbd66/rules.mk54
-rw-r--r--keyboards/kbdfans/kbd67/hotswap/rules.mk51
-rw-r--r--keyboards/kbdfans/kbd67/rev1/rules.mk51
-rw-r--r--keyboards/kbdfans/kbd67/rev2/rules.mk51
-rw-r--r--keyboards/kbdfans/kbd6x/rules.mk54
-rw-r--r--keyboards/kbdfans/kbd75/rev1/rules.mk8
-rw-r--r--keyboards/kbdfans/kbd75/rev2/rules.mk8
-rw-r--r--keyboards/kbdfans/kbd8x/keymaps/default_backlighting/rules.mk1
-rw-r--r--keyboards/kbdfans/kbd8x/rules.mk52
-rw-r--r--keyboards/kbdfans/kbd8x_mk2/rules.mk51
12 files changed, 52 insertions, 431 deletions
diff --git a/keyboards/kbdfans/kbd19x/rules.mk b/keyboards/kbdfans/kbd19x/rules.mk
index b7a08f241..0f6a80f8c 100644
--- a/keyboards/kbdfans/kbd19x/rules.mk
+++ b/keyboards/kbdfans/kbd19x/rules.mk
@@ -1,63 +1,16 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
diff --git a/keyboards/kbdfans/kbd4x/rules.mk b/keyboards/kbdfans/kbd4x/rules.mk
index 7e9ea7912..c5a10bce8 100644
--- a/keyboards/kbdfans/kbd4x/rules.mk
+++ b/keyboards/kbdfans/kbd4x/rules.mk
@@ -1,63 +1,16 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
diff --git a/keyboards/kbdfans/kbd66/rules.mk b/keyboards/kbdfans/kbd66/rules.mk
index ffefc4bc8..7484ca9e7 100644
--- a/keyboards/kbdfans/kbd66/rules.mk
+++ b/keyboards/kbdfans/kbd66/rules.mk
@@ -1,51 +1,15 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
diff --git a/keyboards/kbdfans/kbd67/hotswap/rules.mk b/keyboards/kbdfans/kbd67/hotswap/rules.mk
index f8667d280..4b51619da 100644
--- a/keyboards/kbdfans/kbd67/hotswap/rules.mk
+++ b/keyboards/kbdfans/kbd67/hotswap/rules.mk
@@ -1,63 +1,16 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
diff --git a/keyboards/kbdfans/kbd67/rev1/rules.mk b/keyboards/kbdfans/kbd67/rev1/rules.mk
index 0d7c14ad4..d71446caf 100644
--- a/keyboards/kbdfans/kbd67/rev1/rules.mk
+++ b/keyboards/kbdfans/kbd67/rev1/rules.mk
@@ -1,63 +1,16 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
diff --git a/keyboards/kbdfans/kbd67/rev2/rules.mk b/keyboards/kbdfans/kbd67/rev2/rules.mk
index 5e874a041..431ff194e 100644
--- a/keyboards/kbdfans/kbd67/rev2/rules.mk
+++ b/keyboards/kbdfans/kbd67/rev2/rules.mk
@@ -1,63 +1,16 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#
diff --git a/keyboards/kbdfans/kbd6x/rules.mk b/keyboards/kbdfans/kbd6x/rules.mk
index 72c52d3c6..efdbdbb53 100644
--- a/keyboards/kbdfans/kbd6x/rules.mk
+++ b/keyboards/kbdfans/kbd6x/rules.mk
@@ -1,51 +1,15 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
+BOOTLOADER = atmel-dfu
# Build Options
# change yes to no to disable
diff --git a/keyboards/kbdfans/kbd75/rev1/rules.mk b/keyboards/kbdfans/kbd75/rev1/rules.mk
index 421894a38..de0af62b8 100644
--- a/keyboards/kbdfans/kbd75/rev1/rules.mk
+++ b/keyboards/kbdfans/kbd75/rev1/rules.mk
@@ -2,9 +2,15 @@
MCU = atmega32u4
# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# comment out to disable the options.
#
diff --git a/keyboards/kbdfans/kbd75/rev2/rules.mk b/keyboards/kbdfans/kbd75/rev2/rules.mk
index 421894a38..de0af62b8 100644
--- a/keyboards/kbdfans/kbd75/rev2/rules.mk
+++ b/keyboards/kbdfans/kbd75/rev2/rules.mk
@@ -2,9 +2,15 @@
MCU = atmega32u4
# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# comment out to disable the options.
#
diff --git a/keyboards/kbdfans/kbd8x/keymaps/default_backlighting/rules.mk b/keyboards/kbdfans/kbd8x/keymaps/default_backlighting/rules.mk
deleted file mode 100644
index d98bb1cb1..000000000
--- a/keyboards/kbdfans/kbd8x/keymaps/default_backlighting/rules.mk
+++ /dev/null
@@ -1 +0,0 @@
-#Build Options
diff --git a/keyboards/kbdfans/kbd8x/rules.mk b/keyboards/kbdfans/kbd8x/rules.mk
index f6ed7729c..f0a4689fe 100644
--- a/keyboards/kbdfans/kbd8x/rules.mk
+++ b/keyboards/kbdfans/kbd8x/rules.mk
@@ -1,52 +1,16 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
diff --git a/keyboards/kbdfans/kbd8x_mk2/rules.mk b/keyboards/kbdfans/kbd8x_mk2/rules.mk
index 43e0dcf40..ba8b8ee87 100644
--- a/keyboards/kbdfans/kbd8x_mk2/rules.mk
+++ b/keyboards/kbdfans/kbd8x_mk2/rules.mk
@@ -1,63 +1,16 @@
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
-# atmega32a bootloadHID
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
-# If you don't know the bootloader type, then you can specify the
-# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-# OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
# change yes to no to disable
#