diff options
Diffstat (limited to 'keyboards/speedo')
| -rw-r--r-- | keyboards/speedo/keymaps/default/keymap.c | 16 | ||||
| -rw-r--r-- | keyboards/speedo/rules.mk | 55 |
2 files changed, 9 insertions, 62 deletions
diff --git a/keyboards/speedo/keymaps/default/keymap.c b/keyboards/speedo/keymaps/default/keymap.c index ccfc60856..f5365b122 100644 --- a/keyboards/speedo/keymaps/default/keymap.c +++ b/keyboards/speedo/keymaps/default/keymap.c @@ -55,22 +55,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { }; -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) -{ - // MACRODOWN only works in this function - switch(id) { - case 0: - if (record->event.pressed) { - register_code(KC_RSFT); - } else { - unregister_code(KC_RSFT); - } - break; - } - return MACRO_NONE; -}; - - void matrix_init_user(void) { } diff --git a/keyboards/speedo/rules.mk b/keyboards/speedo/rules.mk index 45eb6ee37..4295e2ad7 100644 --- a/keyboards/speedo/rules.mk +++ b/keyboards/speedo/rules.mk @@ -1,52 +1,15 @@ # MCU name -#MCU = at90usb1286 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable |