diff options
Diffstat (limited to 'LUFA')
22 files changed, 36 insertions, 36 deletions
diff --git a/LUFA/Common/ArchitectureSpecific.h b/LUFA/Common/ArchitectureSpecific.h index 1a05be812..9b719a221 100644 --- a/LUFA/Common/ArchitectureSpecific.h +++ b/LUFA/Common/ArchitectureSpecific.h @@ -66,7 +66,7 @@ #if (ARCH == ARCH_AVR8) || (ARCH == ARCH_XMEGA) || defined(__DOXYGEN__) #if (ARCH == ARCH_AVR8) || defined(__DOXYGEN__) /** Re-enables the AVR's JTAG bus in software, until a system reset. This will re-enable JTAG debugging - * interface after is has been disbled in software via \ref JTAG_DISABLE(). + * interface after is has been disabled in software via \ref JTAG_DISABLE(). * * \note This macro is not available for all architectures. */ diff --git a/LUFA/Common/Attributes.h b/LUFA/Common/Attributes.h index f4040b23e..b058eed8f 100644 --- a/LUFA/Common/Attributes.h +++ b/LUFA/Common/Attributes.h @@ -116,7 +116,7 @@ /** Forces the compiler to not automatically zero the given global variable on startup, so that the * current RAM contents is retained. Under most conditions this value will be random due to the - * behaviour of volatile memory once power is removed, but may be used in some specific circumstances, + * behavior of volatile memory once power is removed, but may be used in some specific circumstances, * like the passing of values back after a system watchdog reset. */ #define ATTR_NO_INIT __attribute__ ((section (".noinit"))) diff --git a/LUFA/Drivers/Board/Buttons.h b/LUFA/Drivers/Board/Buttons.h index 1b70a6bd5..73ccb4194 100644 --- a/LUFA/Drivers/Board/Buttons.h +++ b/LUFA/Drivers/Board/Buttons.h @@ -160,7 +160,7 @@ */ static inline void Buttons_Init(void); - /** Disables the buttons driver, releasing the I/O pins back to their default high-impedence input mode. */ + /** Disables the buttons driver, releasing the I/O pins back to their default high-impedance input mode. */ static inline void Buttons_Disable(void); /** Returns a mask indicating which board buttons are currently pressed. diff --git a/LUFA/Drivers/Board/Joystick.h b/LUFA/Drivers/Board/Joystick.h index 63d28e837..2f90a9ca3 100644 --- a/LUFA/Drivers/Board/Joystick.h +++ b/LUFA/Drivers/Board/Joystick.h @@ -126,7 +126,7 @@ */ static inline void Joystick_Init(void); - /** Disables the joystick driver, releasing the I/O pins back to their default high-impedence input mode. */ + /** Disables the joystick driver, releasing the I/O pins back to their default high-impedance input mode. */ static inline void Joystick_Disable(void); /** Returns the current status of the joystick, as a mask indicating the direction the joystick is diff --git a/LUFA/Drivers/Board/LEDs.h b/LUFA/Drivers/Board/LEDs.h index 97cb81a50..21f89aa58 100644 --- a/LUFA/Drivers/Board/LEDs.h +++ b/LUFA/Drivers/Board/LEDs.h @@ -63,7 +63,7 @@ * * \note To make code as compatible as possible, it is assumed that all boards carry a minimum of four LEDs. If * a board contains less than four LEDs, the remaining LED masks are defined to 0 so as to have no effect. - * If other behaviour is desired, either alias the remaining LED masks to existing LED masks via the -D + * If other behavior is desired, either alias the remaining LED masks to existing LED masks via the -D * switch in the project makefile, or alias them to nothing in the makefile to cause compilation errors when * a non-existing LED is referenced in application code. Note that this means that it is possible to make * compatible code for a board with no LEDs by making a board LED driver (see \ref Page_WritingBoardDrivers) @@ -221,7 +221,7 @@ */ static inline void LEDs_Init(void); - /** Disables the board LED driver, releasing the I/O pins back to their default high-impedence input mode. */ + /** Disables the board LED driver, releasing the I/O pins back to their default high-impedance input mode. */ static inline void LEDs_Disable(void); /** Turns on the LEDs specified in the given LED mask. diff --git a/LUFA/Drivers/Peripheral/AVR8/ADC_AVR8.h b/LUFA/Drivers/Peripheral/AVR8/ADC_AVR8.h index c04d2ba8c..d85fddc28 100644 --- a/LUFA/Drivers/Peripheral/AVR8/ADC_AVR8.h +++ b/LUFA/Drivers/Peripheral/AVR8/ADC_AVR8.h @@ -248,7 +248,7 @@ #define ADC_INT_TEMP_SENS ((1 << 8) | (0x07 << MUX0)) #endif - /** MUX mask define for the internal 1.1V bandgap channel of the ADC. See \ref ADC_StartReading() and \ref ADC_GetChannelReading(). */ + /** MUX mask define for the internal 1.1V band-gap channel of the ADC. See \ref ADC_StartReading() and \ref ADC_GetChannelReading(). */ #define ADC_1100MV_BANDGAP (0x1E << MUX0) /** Retrieves the ADC MUX mask for the given ADC channel number. diff --git a/LUFA/Drivers/USB/Class/Device/AudioClassDevice.h b/LUFA/Drivers/USB/Class/Device/AudioClassDevice.h index a8bfc7833..52c5a1aa1 100644 --- a/LUFA/Drivers/USB/Class/Device/AudioClassDevice.h +++ b/LUFA/Drivers/USB/Class/Device/AudioClassDevice.h @@ -124,7 +124,7 @@ * * When the DataLength parameter is NULL, this callback should only indicate whether the specified operation is valid for * the given endpoint index, and should return as fast as possible. When non-NULL, this value may be altered for GET operations - * to indicate the size of the retreived data. + * to indicate the size of the retrieved data. * * \note The length of the retrieved data stored into the Data buffer on GET operations should not exceed the initial value * of the \c DataLength parameter. @@ -153,7 +153,7 @@ * * When the DataLength parameter is NULL, this callback should only indicate whether the specified operation is valid for * the given entity and should return as fast as possible. When non-NULL, this value may be altered for GET operations - * to indicate the size of the retreived data. + * to indicate the size of the retrieved data. * * \note The length of the retrieved data stored into the Data buffer on GET operations should not exceed the initial value * of the \c DataLength parameter. diff --git a/LUFA/Drivers/USB/Class/Device/MIDIClassDevice.h b/LUFA/Drivers/USB/Class/Device/MIDIClassDevice.h index 2703600ea..52aa9a15d 100644 --- a/LUFA/Drivers/USB/Class/Device/MIDIClassDevice.h +++ b/LUFA/Drivers/USB/Class/Device/MIDIClassDevice.h @@ -130,7 +130,7 @@ /** Flushes the MIDI send buffer, sending any queued MIDI events to the host. This should be called to override the - * \ref MIDI_Device_SendEventPacket() function's packing behaviour, to flush queued events. + * \ref MIDI_Device_SendEventPacket() function's packing behavior, to flush queued events. * * \param[in,out] MIDIInterfaceInfo Pointer to a structure containing a MIDI Class configuration and state. * diff --git a/LUFA/Drivers/USB/Class/Host/AndroidAccessoryClassHost.h b/LUFA/Drivers/USB/Class/Host/AndroidAccessoryClassHost.h index 678feda45..f55cd340a 100644 --- a/LUFA/Drivers/USB/Class/Host/AndroidAccessoryClassHost.h +++ b/LUFA/Drivers/USB/Class/Host/AndroidAccessoryClassHost.h @@ -156,7 +156,7 @@ *
* \param[in,out] AOAInterfaceInfo Pointer to a structure containing an AOA Class host configuration and state.
*
- * \return A value from the \ref USB_Host_SendControlErrorCodes_t enum, or \ref AOA_ERROR_LOGICAL_CMD_FAILED if a logical error occured..
+ * \return A value from the \ref USB_Host_SendControlErrorCodes_t enum, or \ref AOA_ERROR_LOGICAL_CMD_FAILED if a logical error occurred..
*/
uint8_t AOA_Host_StartAccessoryMode(USB_ClassInfo_AOA_Host_t* const AOAInterfaceInfo) ATTR_NON_NULL_PTR_ARG(1);
@@ -311,4 +311,4 @@ /** @} */
- +
diff --git a/LUFA/Drivers/USB/Class/Host/HIDClassHost.h b/LUFA/Drivers/USB/Class/Host/HIDClassHost.h index 882cc31df..21868d9cf 100644 --- a/LUFA/Drivers/USB/Class/Host/HIDClassHost.h +++ b/LUFA/Drivers/USB/Class/Host/HIDClassHost.h @@ -246,7 +246,7 @@ uint8_t HID_Host_SetBootProtocol(USB_ClassInfo_HID_Host_t* const HIDInterfaceInfo) ATTR_NON_NULL_PTR_ARG(1); /** Sets the idle period for the attached HID device to the specified interval. The HID idle period determines the rate - * at which the device should send a report, when no state changes have ocurred; i.e. on HID keyboards, this sets the + * at which the device should send a report, when no state changes have occurred; i.e. on HID keyboards, this sets the * hardware key repeat interval. * * \param[in,out] HIDInterfaceInfo Pointer to a structure containing a HID Class host configuration and state. diff --git a/LUFA/Drivers/USB/Class/Host/MIDIClassHost.h b/LUFA/Drivers/USB/Class/Host/MIDIClassHost.h index b9e861143..06ede7f22 100644 --- a/LUFA/Drivers/USB/Class/Host/MIDIClassHost.h +++ b/LUFA/Drivers/USB/Class/Host/MIDIClassHost.h @@ -145,7 +145,7 @@ MIDI_EventPacket_t* const Event) ATTR_NON_NULL_PTR_ARG(1) ATTR_NON_NULL_PTR_ARG(2); /** Flushes the MIDI send buffer, sending any queued MIDI events to the device. This should be called to override the - * \ref MIDI_Host_SendEventPacket() function's packing behaviour, to flush queued events. Events are queued into the + * \ref MIDI_Host_SendEventPacket() function's packing behavior, to flush queued events. Events are queued into the * pipe bank until either the pipe bank is full, or \ref MIDI_Host_Flush() is called. This allows for multiple MIDI * events to be packed into a single pipe packet, increasing data throughput. * diff --git a/LUFA/Drivers/USB/Core/AVR8/USBController_AVR8.h b/LUFA/Drivers/USB/Core/AVR8/USBController_AVR8.h index 330dd9814..8106988d2 100644 --- a/LUFA/Drivers/USB/Core/AVR8/USBController_AVR8.h +++ b/LUFA/Drivers/USB/Core/AVR8/USBController_AVR8.h @@ -215,7 +215,7 @@ * from the \ref USB_Modes_t enum. * * \param[in] Options Mask indicating the options which should be used when initializing the USB - * interface to control the USB interface's behaviour. This should be comprised of + * interface to control the USB interface's behavior. This should be comprised of * a \c USB_OPT_REG_* mask to control the regulator, a \c USB_OPT_*_PLL mask to control the * PLL, and a \c USB_DEVICE_OPT_* mask (when the device mode is enabled) to set the device * mode speed. diff --git a/LUFA/Drivers/USB/Core/ConfigDescriptor.h b/LUFA/Drivers/USB/Core/ConfigDescriptor.h index 22e76cba9..97fb39b57 100644 --- a/LUFA/Drivers/USB/Core/ConfigDescriptor.h +++ b/LUFA/Drivers/USB/Core/ConfigDescriptor.h @@ -213,7 +213,7 @@ * function. The routine updates the position and remaining configuration descriptor bytes values * automatically. If a comparator routine fails a search, the descriptor pointer is retreated back * so that the next descriptor search invocation will start from the descriptor which first caused the - * original search to fail. This behaviour allows for one comparator to be used immediately after another + * original search to fail. This behavior allows for one comparator to be used immediately after another * has failed, starting the second search from the descriptor which failed the first. * * Comparator functions should be standard functions which accept a pointer to the header of the current diff --git a/LUFA/Drivers/USB/Core/Events.h b/LUFA/Drivers/USB/Core/Events.h index 8d627d4f2..f468b7e65 100644 --- a/LUFA/Drivers/USB/Core/Events.h +++ b/LUFA/Drivers/USB/Core/Events.h @@ -189,7 +189,7 @@ * \note For the microcontrollers with limited USB controller functionality, VBUS sensing is not available. * this means that the current connection state is derived from the bus suspension and wake up events by default, * which is not always accurate (host may suspend the bus while still connected). If the actual connection state - * needs to be determined, VBUS should be routed to an external pin, and the auto-detect behaviour turned off by + * needs to be determined, VBUS should be routed to an external pin, and the auto-detect behavior turned off by * passing the \c NO_LIMITED_CONTROLLER_CONNECT token to the compiler via the -D switch at compile time. The connection * and disconnection events may be manually fired, and the \ref USB_DeviceState global changed manually. * \n\n @@ -207,7 +207,7 @@ * \note For the microcontrollers with limited USB controllers, VBUS sense is not available to the USB controller. * this means that the current connection state is derived from the bus suspension and wake up events by default, * which is not always accurate (host may suspend the bus while still connected). If the actual connection state - * needs to be determined, VBUS should be routed to an external pin, and the auto-detect behaviour turned off by + * needs to be determined, VBUS should be routed to an external pin, and the auto-detect behavior turned off by * passing the \c NO_LIMITED_CONTROLLER_CONNECT token to the compiler via the -D switch at compile time. The connection * and disconnection events may be manually fired, and the \ref USB_DeviceState global changed manually. * \n\n diff --git a/LUFA/Drivers/USB/Core/HostStandardReq.h b/LUFA/Drivers/USB/Core/HostStandardReq.h index 5bdfe45ef..6ad0d2e58 100644 --- a/LUFA/Drivers/USB/Core/HostStandardReq.h +++ b/LUFA/Drivers/USB/Core/HostStandardReq.h @@ -91,7 +91,7 @@ /* Global Variables: */ /** Indicates the currently set configuration number of the attached device. This indicates the currently - * selected configuration value if one has been set sucessfully, or 0 if no configuration has been selected. + * selected configuration value if one has been set successfully, or 0 if no configuration has been selected. * * To set a device configuration, call the \ref USB_Host_SetDeviceConfiguration() function. * diff --git a/LUFA/Drivers/USB/Core/StdDescriptors.h b/LUFA/Drivers/USB/Core/StdDescriptors.h index c46129c48..031e01d28 100644 --- a/LUFA/Drivers/USB/Core/StdDescriptors.h +++ b/LUFA/Drivers/USB/Core/StdDescriptors.h @@ -105,7 +105,7 @@ /** \name USB Configuration Descriptor Attribute Masks */ //@{ /** Mask for the reserved bit in the Configuration Descriptor's \c ConfigAttributes field, which must be set on all - * devices for historial purposes. + * devices for historical purposes. */ #define USB_CONFIG_ATTR_RESERVED 0x80 diff --git a/LUFA/Drivers/USB/Core/UC3/USBController_UC3.h b/LUFA/Drivers/USB/Core/UC3/USBController_UC3.h index 92e245ca2..4a5d267c8 100644 --- a/LUFA/Drivers/USB/Core/UC3/USBController_UC3.h +++ b/LUFA/Drivers/USB/Core/UC3/USBController_UC3.h @@ -172,7 +172,7 @@ * from the \ref USB_Modes_t enum. * * \param[in] Options Mask indicating the options which should be used when initializing the USB - * interface to control the USB interface's behaviour. This should be comprised of + * interface to control the USB interface's behavior. This should be comprised of * a \c USB_OPT_REG_* mask to control the regulator, a \c USB_OPT_*_PLL mask to control the * PLL, and a \c USB_DEVICE_OPT_* mask (when the device mode is enabled) to set the device * mode speed. diff --git a/LUFA/Drivers/USB/Core/XMEGA/USBController_XMEGA.h b/LUFA/Drivers/USB/Core/XMEGA/USBController_XMEGA.h index 25402e855..e1c782db6 100644 --- a/LUFA/Drivers/USB/Core/XMEGA/USBController_XMEGA.h +++ b/LUFA/Drivers/USB/Core/XMEGA/USBController_XMEGA.h @@ -180,7 +180,7 @@ * from the \ref USB_Modes_t enum. * * \param[in] Options Mask indicating the options which should be used when initializing the USB - * interface to control the USB interface's behaviour. This should be comprised of + * interface to control the USB interface's behavior. This should be comprised of * a \c USB_OPT_REG_* mask to control the regulator, a \c USB_OPT_*_PLL mask to control the * PLL, and a \c USB_DEVICE_OPT_* mask (when the device mode is enabled) to set the device * mode speed. diff --git a/LUFA/Platform/Platform.h b/LUFA/Platform/Platform.h index 3bbd697ff..db5f43535 100644 --- a/LUFA/Platform/Platform.h +++ b/LUFA/Platform/Platform.h @@ -37,7 +37,7 @@ * management. * * User code may choose to either include this master dispatch header file to include all available platform - * driver header files for the current achitecture, or may choose to only include the specific platform driver + * driver header files for the current architecture, or may choose to only include the specific platform driver * modules required for a particular application. */ @@ -55,7 +55,7 @@ * system functions such as clock control and interrupt management. * * User code may choose to either include this master dispatch header file to include all available platform - * driver header files for the current achitecture, or may choose to only include the specific platform driver + * driver header files for the current architecture, or may choose to only include the specific platform driver * modules required for a particular application. * * \note The exact APIs and availability of sub-modules within the platform driver group may vary depending on the diff --git a/LUFA/Platform/UC3/ClockManagement.h b/LUFA/Platform/UC3/ClockManagement.h index 2cd96d2ec..51cb0ff6d 100644 --- a/LUFA/Platform/UC3/ClockManagement.h +++ b/LUFA/Platform/UC3/ClockManagement.h @@ -91,16 +91,16 @@ EXOSC_MODE_8MHZ_OR_MORE = AVR32_PM_OSCCTRL0_MODE_CRYSTAL_G3, /**< External crystal oscillator equal to or faster than 8MHz. */ }; - /** Enum for the possible external oscillator statup times. */ + /** Enum for the possible external oscillator startup times. */ enum UC3_Extern_OSC_ClockStartup_t { EXOSC_START_0CLK = AVR32_PM_OSCCTRL0_STARTUP_0_RCOSC, /**< Immediate startup, no delay. */ - EXOSC_START_64CLK = AVR32_PM_OSCCTRL0_STARTUP_64_RCOSC, /**< Wait 64 clock cyles before startup for stability. */ - EXOSC_START_128CLK = AVR32_PM_OSCCTRL0_STARTUP_128_RCOSC, /**< Wait 128 clock cyles before startup for stability. */ - EXOSC_START_2048CLK = AVR32_PM_OSCCTRL0_STARTUP_2048_RCOSC, /**< Wait 2048 clock cyles before startup for stability. */ - EXOSC_START_4096CLK = AVR32_PM_OSCCTRL0_STARTUP_4096_RCOSC, /**< Wait 4096 clock cyles before startup for stability. */ - EXOSC_START_8192CLK = AVR32_PM_OSCCTRL0_STARTUP_8192_RCOSC, /**< Wait 8192 clock cyles before startup for stability. */ - EXOSC_START_16384CLK = AVR32_PM_OSCCTRL0_STARTUP_16384_RCOSC, /**< Wait 16384 clock cyles before startup for stability. */ + EXOSC_START_64CLK = AVR32_PM_OSCCTRL0_STARTUP_64_RCOSC, /**< Wait 64 clock cycles before startup for stability. */ + EXOSC_START_128CLK = AVR32_PM_OSCCTRL0_STARTUP_128_RCOSC, /**< Wait 128 clock cycles before startup for stability. */ + EXOSC_START_2048CLK = AVR32_PM_OSCCTRL0_STARTUP_2048_RCOSC, /**< Wait 2048 clock cycles before startup for stability. */ + EXOSC_START_4096CLK = AVR32_PM_OSCCTRL0_STARTUP_4096_RCOSC, /**< Wait 4096 clock cycles before startup for stability. */ + EXOSC_START_8192CLK = AVR32_PM_OSCCTRL0_STARTUP_8192_RCOSC, /**< Wait 8192 clock cycles before startup for stability. */ + EXOSC_START_16384CLK = AVR32_PM_OSCCTRL0_STARTUP_16384_RCOSC, /**< Wait 16384 clock cycles before startup for stability. */ }; /** Enum for the possible module clock sources. */ diff --git a/LUFA/Platform/UC3/InterruptManagement.h b/LUFA/Platform/UC3/InterruptManagement.h index 49bdaf8d5..7441a3011 100644 --- a/LUFA/Platform/UC3/InterruptManagement.h +++ b/LUFA/Platform/UC3/InterruptManagement.h @@ -93,7 +93,7 @@ /* Public Interface - May be used in end-application: */ /* Macros: */ - /** Converts a given interrupt index into its assocated interrupt group. + /** Converts a given interrupt index into its associated interrupt group. * * \param[in] IRQIndex Index of the interrupt request to convert. * @@ -101,7 +101,7 @@ */ #define INTC_IRQ_GROUP(IRQIndex) (IRQIndex / 32) - /** Converts a given interrupt index into its assocated interrupt line. + /** Converts a given interrupt index into its associated interrupt line. * * \param[in] IRQIndex Index of the interrupt request to convert. * diff --git a/LUFA/Platform/XMEGA/ClockManagement.h b/LUFA/Platform/XMEGA/ClockManagement.h index feef8898e..c0553aeb9 100644 --- a/LUFA/Platform/XMEGA/ClockManagement.h +++ b/LUFA/Platform/XMEGA/ClockManagement.h @@ -88,7 +88,7 @@ EXOSC_FREQ_16MHZ_MAX = OSC_FRQRANGE_12TO16_gc, /**< External crystal oscillator equal to or slower than 16MHz. */ }; - /** Enum for the possible external oscillator statup times. */ + /** Enum for the possible external oscillator startup times. */ enum XMEGA_Extern_OSC_ClockStartup_t { EXOSC_START_6CLK = OSC_XOSCSEL_EXTCLK_gc, /**< Wait 6 clock cycles before startup (external clock). */ @@ -141,7 +141,7 @@ * the oscillator is ready for use. * * \param[in] FreqRange Frequency range of the external oscillator, a value from \ref XMEGA_Extern_OSC_ClockFrequency_t. - * \param[in] Startup Statup time of the external oscillator, a value from \ref XMEGA_Extern_OSC_ClockStartup_t. + * \param[in] Startup Startup time of the external oscillator, a value from \ref XMEGA_Extern_OSC_ClockStartup_t. * * \return Boolean \c true if the external oscillator was successfully started, \c false if invalid parameters specified. */ @@ -347,7 +347,7 @@ * * \param[in] Source Clock source for the CPU core, a value from \ref XMEGA_System_ClockSource_t. * - * \return Boolean \c true if the CPU core clock was sucessfully altered, \c false if invalid parameters specified. + * \return Boolean \c true if the CPU core clock was successfully altered, \c false if invalid parameters specified. */ static inline bool XMEGACLK_SetCPUClockSource(const uint8_t Source) ATTR_ALWAYS_INLINE; static inline bool XMEGACLK_SetCPUClockSource(const uint8_t Source) |