diff options
Diffstat (limited to 'Projects/XPLAINBridge/Lib/SoftUART.c')
-rw-r--r-- | Projects/XPLAINBridge/Lib/SoftUART.c | 43 |
1 files changed, 20 insertions, 23 deletions
diff --git a/Projects/XPLAINBridge/Lib/SoftUART.c b/Projects/XPLAINBridge/Lib/SoftUART.c index ff152e7eb..81f023740 100644 --- a/Projects/XPLAINBridge/Lib/SoftUART.c +++ b/Projects/XPLAINBridge/Lib/SoftUART.c @@ -63,41 +63,38 @@ void SoftUART_Init(void) EICRA = (1 << ISC01); EIMSK = (1 << INT0); - /* Ensure that when the timer is enabled the transmission ISR runs immediately */ - OCR1B = TCNT1 + 1; - - /* Start timer 1 with transmission channel force-enabled so that it will immediatly fire */ - TCCR1C = (1 << FOC1B); - TIMSK1 = (1 << OCIE1B); + /* Start software UART transmission and reception timers */ + TIMSK3 = (1 << OCIE3A); + TCCR3B = (1 << CS30); TCCR1B = (1 << CS10); } /** ISR to detect the start of a bit being sent to the software UART. */ -ISR(INT0_vect) +ISR(INT0_vect, ISR_BLOCK) { /* Set reception channel to fire 1.5 bits past the beginning of the start bit */ - OCR1A = TCNT1 + ((BIT_TIME * 3) / 2); - + OCR1A = TCNT1 + (BIT_TIME + (BIT_TIME / 2)); + /* Clear the received data temporary variable, reset the current received bit position mask */ RX_Data = 0; RX_BitMask = (1 << 0); - /* Clear reception channel ISR flag in case it is pending */ - TIFR1 = (1 << OCF1A); - /* Check that the start bit is still low to prevent noise from triggering a reception */ if (!(SRXPIN & (1 << SRX))) - { - /* Still low, enable both send and receive channels */ - TIMSK1 = (1 << OCIE1A) | (1 << OCIE1B); - - /* Clear the start bit detection ISR flag if it is pending */ + { + /* Clear reception channel ISR flag in case it is pending */ + TIFR1 = (1 << OCF1A); + + /* Still low, enable bit receive ISR */ + TIMSK1 = (1 << OCIE1A); + + /* Clear the start bit detection ISR flag */ EIMSK &= ~(1 << INT0); } } /** ISR to manage the reception of bits to the software UART. */ -ISR(TIMER1_COMPA_vect) +ISR(TIMER1_COMPA_vect, ISR_BLOCK) { /* Move the reception ISR compare position one bit ahead */ OCR1A += BIT_TIME; @@ -118,17 +115,17 @@ ISR(TIMER1_COMPA_vect) RingBuffer_Insert(&UARTtoUSB_Buffer, RX_Data); /* Disable the reception ISR as all data has now been received, re-enable start bit detection ISR */ - TIMSK1 = (1 << OCIE1B); - EIMSK |= (1 << INT0); - EIFR = (1 << INTF0); + TIMSK1 = 0; + EIFR = (1 << INTF0); + EIMSK = (1 << INT0); } } /** ISR to manage the transmission of bits via the software UART. */ -ISR(TIMER1_COMPB_vect) +ISR(TIMER3_COMPA_vect, ISR_NOBLOCK) { /* Move the transmission ISR compare position one bit ahead */ - OCR1B += BIT_TIME; + OCR3A += BIT_TIME; /* Check if transmission has finished */ if (TX_BitsRemaining) |