blob: 8d299e25a02c0207a29b966ea1d1476f51d2a810 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
|
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage AVRISP MKII Programmer Project
*
* \section SSec_Compat Demo Compatibility:
*
* The following table indicates what microcontrollers are compatible with this demo.
*
* - AT90USB1287
* - AT90USB1286
* - AT90USB647
* - AT90USB646
* - ATMEGA32U6
* - ATMEGA32U4
* - ATMEGA16U4
* - AT90USB162
* - AT90USB82
*
* \section SSec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this demo.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>Vendor Specific Class</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>N/A</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>Atmel AVRISP MKII Protocol Specification</td>
* </tr>
* <tr>
* <td><b>Usable Speeds:</b></td>
* <td>Full Speed Mode</td>
* </tr>
* </table>
*
* \section SSec_Description Project Description:
*
* Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of
* microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its
* most basic form, it allows for the programming of 5V AVRs from within AVRStudio with no special hardware other than
* the USB AVR and the parts needed for the USB interface. If the user desires, more advanced circuits incorporating
* level conversion can be made to allow for the programming of 3.3V AVR designs.
*
* This device spoofs Atmel's official AVRISP-MKII device PID so that it remains compatible with Atmel's AVRISP-MKII
* drivers. When promted, direct your OS to install Atmel's AVRISP-MKII drivers provided with AVRStudio.
*
* Note that this design currently has several limitations:
* - Minimum target clock speed of 500KHz due to hardware SPI used
* - No reversed/shorted target connector detection and notification
*
* On AVR models with an ADC converter, ACC should be tied to 5V (e.g. VBUS) and the VTARGET_ADC_CHANNEL token should be
* set to an appropriate ADC channel number in the project makefile for VTARGET detection to operate correctly. On models
* without an ADC converter, VTARGET will report at a fixed 5V level.
*
* \section SSec_Options Project Options
*
* The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
*
* <table>
* <tr>
* <td><b>Define Name:</b></td>
* <td><b>Location:</b></td>
* <td><b>Description:</b></td>
* </tr>
* <tr>
* <td>RESET_LINE_PORT</td>
* <td>Makefile CDEFS</td>
* <td>PORT register for the programmer's target RESET line.</td>
* </tr>
* <tr>
* <td>RESET_LINE_DDR</td>
* <td>Makefile CDEFS</td>
* <td>DDR register for the programmer's target RESET line.</td>
* </tr>
* <tr>
* <td>RESET_LINE_MASK</td>
* <td>Makefile CDEFS</td>
* <td>Mask for the programmer's target RESET line on the chosen port.</td>
* </tr>
* <tr>
* <td>VTARGET_ADC_CHANNEL</td>
* <td>Makefile CDEFS</td>
* <td>ADC channel number (on supported AVRs) to use for VTARGET level detection.</td>
* </tr>
* </table>
*/
|