blob: 249976350f2b916ca306b0ab6113235be356e45e (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
|
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage AVRISP MKII Programmer Project
*
* \section SSec_Compat Demo Compatibility:
*
* The following list indicates what microcontrollers are compatible with this demo.
*
* - Series 7 USB AVRs
* - Series 6 USB AVRs
* - Series 4 USB AVRs
* - Series 2 USB AVRs
*
* \section SSec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this demo.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>Vendor Specific Class</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>N/A</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>Atmel AVRISP MKII Protocol Specification</td>
* </tr>
* <tr>
* <td><b>Usable Speeds:</b></td>
* <td>Full Speed Mode</td>
* </tr>
* </table>
*
* \section SSec_Description Project Description:
*
* Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of
* microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its
* most basic form, it allows for the programming of 5V AVRs from within AVRStudio with no special hardware other than
* the USB AVR and the parts needed for the USB interface. If the user desires, more advanced circuits incorporating
* level conversion can be made to allow for the programming of 3.3V AVR designs.
*
* This device spoofs Atmel's official AVRISP-MKII device PID so that it remains compatible with Atmel's AVRISP-MKII
* drivers. When promted, direct your OS to install Atmel's AVRISP-MKII drivers provided with AVRStudio.
*
* Note that this design currently has several limitations:
* - Minimum target clock speed of 500KHz due to hardware SPI used
* - No reversed/shorted target connector detection and notification
*
* On AVR models with an ADC converter, ACC should be tied to 5V (e.g. VBUS) and the VTARGET_ADC_CHANNEL token should be
* set to an appropriate ADC channel number in the project makefile for VTARGET detection to operate correctly. On models
* without an ADC converter, VTARGET will report at a fixed 5V level.
*
* Connections to the device are simple:
*
* <table>
* <tr>
* <td><b>Programmer Pin:</b></td>
* <td><b>Target Device Pin:</b></td>
* <td><b>ISP 6 Pin Layout:</b></td>
* </tr>
* <tr>
* <td>MISO</td>
* <td>PDO</td>
* <td>1</td>
* </tr>
* <tr>
* <td>ADCx <b><sup>1</sup></b></td>
* <td>VTARGET</td>
* <td>2</td>
* </tr>
* <tr>
* <td>SCLK</td>
* <td>SCLK</td>
* <td>3</td>
* </tr>
* <tr>
* <td>MOSI</td>
* <td>PDI</td>
* <td>4</td>
* </tr>
* <tr>
* <td>PORTx.y <b><sup>2</sup></b></td>
* <td>/RESET</td>
* <td>5</td>
* </tr>
* <tr>
* <td>GND</td>
* <td>GND</td>
* <td>6</td>
* </tr>
* </table>
*
* <b><sup>1</sup></b> <i>Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only</i> \n
* <b><sup>2</sup></b> <i>See \ref SSec_Options section</i>
*
* \section SSec_Options Project Options
*
* The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
*
* <table>
* <tr>
* <td><b>Define Name:</b></td>
* <td><b>Location:</b></td>
* <td><b>Description:</b></td>
* </tr>
* <tr>
* <td>RESET_LINE_PORT</td>
* <td>Makefile CDEFS</td>
* <td>PORT register for the programmer's target RESET line.</td>
* </tr>
* <tr>
* <td>RESET_LINE_DDR</td>
* <td>Makefile CDEFS</td>
* <td>DDR register for the programmer's target RESET line.</td>
* </tr>
* <tr>
* <td>RESET_LINE_MASK</td>
* <td>Makefile CDEFS</td>
* <td>Mask for the programmer's target RESET line on the chosen port. <b>Must not be the AVR's /SS pin</b>, as the
* target pins are tri-stated when not in use, and low signals on the /SS pin will force SPI slave mode when the
* pin is configured as an input.</td>
* </tr>
* <tr>
* <td>VTARGET_ADC_CHANNEL</td>
* <td>Makefile CDEFS</td>
* <td>ADC channel number (on supported AVRs) to use for VTARGET level detection.</td>
* </tr>
* </table>
*/
|