added Olimex-STM32-LCD

2 files changed, 0 insertions, 252 deletions

diff --git a/boards/addons/gdisp/board_ILI9320_olimex_stm32_lcd.h b/boards/addons/gdisp/board_ILI9320_olimex_stm32_lcd.h
deleted file mode 100644
index bca5caf8..00000000
--- a/boards/addons/gdisp/board_ILI9320_olimex_stm32_lcd.h
+++ /dev/null
@@ -1,100 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/gdisp/ILI9320/board_ILI9320_olimex_stm32_lcd.h
- * @brief   GDISP Graphic Driver subsystem board interface for the ILI9320 display.
- */
-
-#ifndef GDISP_LLD_BOARD_H
-#define GDISP_LLD_BOARD_H
-
-// For a multiple display configuration we would put all this in a structure and then
-//	set g->board to that structure.
-#define GDISP_REG              (*((volatile uint16_t *) 0x60000000)) /* RS = 0 */
-#define GDISP_RAM              (*((volatile uint16_t *) 0x60100000)) /* RS = 1 */
-
-static inline void init_board(GDisplay *g) {
-
-	// As we are not using multiple displays we set g->board to NULL as we don't use it.
-	g->board = 0;
-
-	switch(g->controllerdisplay) {
-	case 0:											// Set up for Display 0
-		/* FSMC setup for F1 */
-		rccEnableAHB(RCC_AHBENR_FSMCEN, 0);
-
-		/* set pin modes */
-		IOBus busD = {GPIOD, PAL_WHOLE_PORT, 0};
-		IOBus busE = {GPIOE, PAL_WHOLE_PORT, 0};
-		palSetBusMode(&busD, PAL_MODE_STM32_ALTERNATE_PUSHPULL);
-		palSetBusMode(&busE, PAL_MODE_STM32_ALTERNATE_PUSHPULL);
-		palSetPadMode(GPIOE, GPIOE_TFT_RST, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, GPIOD_TFT_LIGHT, PAL_MODE_OUTPUT_PUSHPULL);
-
-		/* FSMC timing */
-		FSMC_Bank1->BTCR[0+1] = (6) | (10 << 8) | (10 << 16);
-
-		/* Bank1 NOR/SRAM control register configuration
-		 * This is actually not needed as already set by default after reset */
-		FSMC_Bank1->BTCR[0] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
-		break;
-	}
-}
-
-static inline void post_init_board(GDisplay *g) {
-	(void) g;
-}
-
-static inline void setpin_reset(GDisplay *g, bool_t state) {
-	(void) g;
-	if(state)
-		palClearPad(GPIOE, GPIOE_TFT_RST);
-	else
-		palSetPad(GPIOE, GPIOE_TFT_RST);
-}
-
-static inline void set_backlight(GDisplay *g, uint8_t percent) {
-	(void) g;
-	if(percent)
-		palClearPad(GPIOD, GPIOD_TFT_LIGHT);
-	else
-		palSetPad(GPIOD, GPIOD_TFT_LIGHT);
-}
-
-static inline void acquire_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void release_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void write_index(GDisplay *g, uint16_t index) {
-	(void) g;
-	GDISP_REG = index;
-}
-
-static inline void write_data(GDisplay *g, uint16_t data) {
-	(void) g;
-	GDISP_RAM = data;
-}
-
-static inline void setreadmode(GDisplay *g) {
-	(void) g;
-}
-
-static inline void setwritemode(GDisplay *g) {
-	(void) g;
-}
-
-static inline uint16_t read_data(GDisplay *g) {
-	(void) g;
-	return GDISP_RAM;
-}
-
-#endif /* GDISP_LLD_BOARD_H */
diff --git a/boards/addons/ginput/touch/MCU/ginput_lld_mouse_board_olimex_stm32_lcd.h b/boards/addons/ginput/touch/MCU/ginput_lld_mouse_board_olimex_stm32_lcd.h
deleted file mode 100644
index ca177a89..00000000
--- a/boards/addons/ginput/touch/MCU/ginput_lld_mouse_board_olimex_stm32_lcd.h
+++ /dev/null
@@ -1,152 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/ginput/touch/MCU/ginput_lld_mouse_board_olimex_stm32_lcd.h
- * @brief   GINPUT Touch low level driver source for the MCU on the example board.
- *
- * @defgroup Mouse Mouse
- * @ingroup GINPUT
- *
- * @{
- */
-
-#ifndef _GINPUT_LLD_MOUSE_BOARD_H
-#define _GINPUT_LLD_MOUSE_BOARD_H
-
-#define ADC_NUM_CHANNELS   2
-#define ADC_BUF_DEPTH      1
-
-static const ADCConversionGroup adc_y_config = { 
-    FALSE,
-    ADC_NUM_CHANNELS,
-    NULL,
-    NULL,
-    0, 0,    
-    0, 0,    
-    ADC_SQR1_NUM_CH(ADC_NUM_CHANNELS),
-    0,    
-    ADC_SQR3_SQ2_N(ADC_CHANNEL_IN12) | ADC_SQR3_SQ1_N(ADC_CHANNEL_IN13)
-};
-
-static const ADCConversionGroup adc_x_config = { 
-    FALSE,
-    ADC_NUM_CHANNELS,
-    NULL,
-    NULL,
-    0, 0,
-    0, 0,
-    ADC_SQR1_NUM_CH(ADC_NUM_CHANNELS),
-    0,  
-    ADC_SQR3_SQ2_N(ADC_CHANNEL_IN10) | ADC_SQR3_SQ1_N(ADC_CHANNEL_IN11)
-};
-
-/**
- * @brief   Initialise the board for the touch.
- *
- * @notapi
- */
-static inline void init_board(void) {
-	adcStart(&ADCD1, NULL);
-}
-
-/**
- * @brief   Check whether the surface is currently touched
- * @return	TRUE if the surface is currently touched
- *
- * @notapi
- */
-static inline bool_t getpin_pressed(void) {
-    palSetPadMode(GPIOC, 0, PAL_MODE_INPUT_PULLDOWN);
-    palSetPadMode(GPIOC, 1, PAL_MODE_INPUT);
-    palSetPadMode(GPIOC, 2, PAL_MODE_INPUT);
-    palSetPadMode(GPIOC, 3, PAL_MODE_OUTPUT_PUSHPULL);
-    palSetPad(GPIOC, 3);
-	
-	return palReadPad(GPIOC, 0);
-}
-
-/**
- * @brief   Aquire the bus ready for readings
- *
- * @notapi
- */
-static inline void aquire_bus(void) {
-
-}
-
-/**
- * @brief   Release the bus after readings
- *
- * @notapi
- */
-static inline void release_bus(void) {
-
-}
-
-/**
- * @brief   Read an x value from touch controller
- * @return	The value read from the controller
- *
- * @notapi
- */
-static inline uint16_t read_x_value(void) {
-	uint16_t val1, val2;
-    adcsample_t samples[ADC_NUM_CHANNELS * ADC_BUF_DEPTH];
-
-    palSetPadMode(GPIOC, 0, PAL_MODE_INPUT_ANALOG);
-    palSetPadMode(GPIOC, 1, PAL_MODE_INPUT_ANALOG);
-    palSetPadMode(GPIOC, 2, PAL_MODE_OUTPUT_PUSHPULL);
-    palSetPadMode(GPIOC, 3, PAL_MODE_OUTPUT_PUSHPULL);
-    
-	palSetPad(GPIOC, 2);
-    palClearPad(GPIOC, 3); 
-    gfxSleepMilliseconds(1);
-    adcConvert(&ADCD1, &adc_x_config, samples, ADC_BUF_DEPTH);  
-    val1 = ((samples[0] + samples[1])/2);
-    
-	palClearPad(GPIOC, 2);
-    palSetPad(GPIOC, 3);
-    gfxSleepMilliseconds(1);
-    adcConvert(&ADCD1, &adc_x_config, samples, ADC_BUF_DEPTH);
-    val2 = ((samples[0] + samples[1])/2);
-    
-	return ((val1+((1<<12)-val2))/4);
-}
-
-/**
- * @brief   Read an y value from touch controller
- * @return	The value read from the controller
- *
- * @notapi
- */
-static inline uint16_t read_y_value(void) {
-	uint16_t val1, val2;
-    adcsample_t samples[ADC_NUM_CHANNELS * ADC_BUF_DEPTH];
-
-    palSetPadMode(GPIOC, 2, PAL_MODE_INPUT_ANALOG);
-    palSetPadMode(GPIOC, 3, PAL_MODE_INPUT_ANALOG);
-    palSetPadMode(GPIOC, 0, PAL_MODE_OUTPUT_PUSHPULL);
-    palSetPadMode(GPIOC, 1, PAL_MODE_OUTPUT_PUSHPULL);
-
-    palSetPad(GPIOC, 1);
-    palClearPad(GPIOC, 0);
-    gfxSleepMilliseconds(1);
-    adcConvert(&ADCD1, &adc_y_config, samples, ADC_BUF_DEPTH);
-    val1 = ((samples[0] + samples[1])/2);
-
-    palClearPad(GPIOC, 1);
-    palSetPad(GPIOC, 0);
-    gfxSleepMilliseconds(1);
-    adcConvert(&ADCD1, &adc_y_config, samples, ADC_BUF_DEPTH);
-    val2 = ((samples[0] + samples[1])/2);
-    
-	return ((val1+((1<<12)-val2))/4);
-}
-
-#endif /* _GINPUT_LLD_MOUSE_BOARD_H */
-/** @} */