fixed some boards file names

6 files changed, 0 insertions, 660 deletions

diff --git a/boards/base/Embest-STM32-DMSTF4BB/board_SSD2119_embest_dmstf4bb.h b/boards/base/Embest-STM32-DMSTF4BB/board_SSD2119_embest_dmstf4bb.h
deleted file mode 100644
index c6d3d040..00000000
--- a/boards/base/Embest-STM32-DMSTF4BB/board_SSD2119_embest_dmstf4bb.h
+++ /dev/null
@@ -1,168 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-#ifndef _GDISP_LLD_BOARD_H
-#define _GDISP_LLD_BOARD_H
-
-// For a multiple display configuration we would put all this in a structure and then
-//	set g->board to that structure.
-
-/* Using FSMC A19 (PE3) as DC */
-#define GDISP_REG (*((volatile uint16_t *) 0x60000000)) /* DC = 0 */
-#define GDISP_RAM (*((volatile uint16_t *) 0x60100000)) /* DC = 1 */
-#define GDISP_DMA_STREAM STM32_DMA2_STREAM6
-
-#define SET_RST palSetPad(GPIOD, 3);
-#define CLR_RST palClearPad(GPIOD, 3);
-
-/*
- * PWM configuration structure. We use timer 4 channel 2 (orange LED on board).
- * The reason for so high clock is that with any lower, onboard coil is squeaking.
- * The major disadvantage of this clock is a lack of linearity between PWM duty
- * cycle width and brightness. In fact only with low preset one sees any change
- * (eg. duty cycle between 1-20). Feel free to adjust this, maybe only my board
- * behaves like this. According to the G5126 datesheet (backlight LED driver)
- * the PWM frequency should be somewhere between 200 Hz to 200 kHz.
- */
-static const PWMConfig pwmcfg = {
-	1000000,       /* 1 MHz PWM clock frequency. */
-	100,           /* PWM period is 100 cycles. */
-	NULL,
-	{
-		{PWM_OUTPUT_ACTIVE_HIGH, NULL},
-		{PWM_OUTPUT_ACTIVE_HIGH, NULL},
-		{PWM_OUTPUT_ACTIVE_HIGH, NULL},
-		{PWM_OUTPUT_ACTIVE_HIGH, NULL}
-	},
-	0
-};
-
-static inline void init_board(GDisplay *g) {
-
-	// As we are not using multiple displays we set g->board to NULL as we don't use it.
-	g->board = 0;
-
-	switch(g->controllerdisplay) {
-	case 0:											// Set up for Display 0
-		#if defined(STM32F4XX) || defined(STM32F2XX)
-			/* STM32F4 FSMC init */
-			rccEnableAHB3(RCC_AHB3ENR_FSMCEN, 0);
-
-			#if defined(GDISP_USE_DMA) && defined(GDISP_DMA_STREAM)
-				if (dmaStreamAllocate(GDISP_DMA_STREAM, 0, NULL, NULL))
-					gfxExit();
-				dmaStreamSetMemory0(GDISP_DMA_STREAM, &GDISP_RAM);
-				dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
-			#endif
-		#else
-			#error "FSMC not implemented for this device"
-		#endif
-
-		/* Group pins */
-		IOBus busD = {GPIOD, (1 << 0) | (1 << 1) | (1 << 4) | (1 << 5) | (1 << 7) | (1 << 8) |
-								(1 << 9) | (1 << 10) | (1 << 14) | (1 << 15), 0};
-
-		IOBus busE = {GPIOE, (1 << 3) | (1 << 7) | (1 << 8) | (1 << 9) | (1 << 10) | (1 << 11) | (1 << 12) |
-								(1 << 13) | (1 << 14) | (1 << 15), 0};
-
-		/* FSMC is an alternate function 12 (AF12) */
-		palSetBusMode(&busD, PAL_MODE_ALTERNATE(12));
-		palSetBusMode(&busE, PAL_MODE_ALTERNATE(12));
-
-		/* FSMC timing register configuration */
-		FSMC_Bank1->BTCR[0 + 1] = (FSMC_BTR1_ADDSET_2 | FSMC_BTR1_ADDSET_1) \
-				| (FSMC_BTR1_DATAST_2 | FSMC_BTR1_DATAST_1) \
-				| FSMC_BTR1_BUSTURN_0;
-
-		/* Bank1 NOR/PSRAM control register configuration
-		 * Write enable, memory databus width set to 16 bit, memory bank enable */
-		FSMC_Bank1->BTCR[0] = FSMC_BCR1_WREN | FSMC_BCR1_MWID_0 | FSMC_BCR1_MBKEN;
-
-		/* Display backlight control */
-		/* TIM4 is an alternate function 2 (AF2) */
-		pwmStart(&PWMD4, &pwmcfg);
-		palSetPadMode(GPIOD, 13, PAL_MODE_ALTERNATE(2));
-		pwmEnableChannel(&PWMD4, 1, 100);
-		break;
-	}
-}
-
-static inline void post_init_board(GDisplay *g) {
-	(void) g;
-}
-
-static inline void setpin_reset(GDisplay *g, bool_t state) {
-	(void) g;
-	if (state) {
-		CLR_RST;
-	} else {
-		SET_RST;
-	}
-}
-
-static inline void set_backlight(GDisplay *g, uint8_t percent) {
-	(void) g;
-	pwmEnableChannel(&PWMD4, 1, percent);
-}
-
-static inline void acquire_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void release_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void write_index(GDisplay *g, uint16_t index) {
-	(void) g;
-	GDISP_REG = index;
-}
-
-static inline void write_data(GDisplay *g, uint16_t data) {
-	(void) g;
-	GDISP_RAM = data;
-}
-
-static inline void setreadmode(GDisplay *g) {
-	(void) g;
-}
-
-static inline void setwritemode(GDisplay *g) {
-	(void) g;
-}
-
-static inline uint16_t read_data(GDisplay *g) {
-	(void) g;
-	return GDISP_RAM;
-}
-
-#if defined(GDISP_USE_DMA)
-	static inline void dma_with_noinc(GDisplay *g, color_t *buffer, int area) {
-		(void) g;
-		dmaStreamSetPeripheral(GDISP_DMA_STREAM, buffer);
-		dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
-		for (; area > 0; area -= 65535) {
-			dmaStreamSetTransactionSize(GDISP_DMA_STREAM, area > 65535 ? 65535 : area);
-			dmaStreamEnable(GDISP_DMA_STREAM);
-			dmaWaitCompletion(GDISP_DMA_STREAM);
-		}
-	}
-
-	static inline void dma_with_inc(GDisplay *g, color_t *buffer, int area) {
-		(void) g;
-        dmaStreamSetPeripheral(GDISP_DMA_STREAM, buffer);
-        dmaStreamSetMode(GDISP_DMA_STREAM, STM32_DMA_CR_PL(0) | STM32_DMA_CR_PINC | STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD | STM32_DMA_CR_DIR_M2M);
-		for (; area > 0; area -= 65535) {
-			dmaStreamSetTransactionSize(GDISP_DMA_STREAM, area > 65535 ? 65535 : area);
-			dmaStreamEnable(GDISP_DMA_STREAM);
-			dmaWaitCompletion(GDISP_DMA_STREAM);
-		}
-	}
-#endif
-
-#endif /* _GDISP_LLD_BOARD_H */
-
diff --git a/boards/base/Embest-STM32-DMSTF4BB/ginput_lld_mouse_board_embest_dmstf4bb.h b/boards/base/Embest-STM32-DMSTF4BB/ginput_lld_mouse_board_embest_dmstf4bb.h
deleted file mode 100644
index 6eff87c9..00000000
--- a/boards/base/Embest-STM32-DMSTF4BB/ginput_lld_mouse_board_embest_dmstf4bb.h
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-#ifndef _GINPUT_LLD_MOUSE_BOARD_H
-#define _GINPUT_LLD_MOUSE_BOARD_H
-
-static const I2CConfig i2ccfg = {
-	OPMODE_I2C,
-	400000,
-	FAST_DUTY_CYCLE_2,
-};
-
-static void init_board(void)
-{
-	palSetPadMode(GPIOC, 13, PAL_MODE_INPUT | PAL_STM32_PUDR_FLOATING);			/* TP IRQ */
-	palSetPadMode(GPIOB, 8, PAL_MODE_ALTERNATE(4) | PAL_STM32_OTYPE_OPENDRAIN);	/* SCL */
-	palSetPadMode(GPIOB, 9, PAL_MODE_ALTERNATE(4) | PAL_STM32_OTYPE_OPENDRAIN);	/* SDA */
-
-	i2cStart(&I2CD1, &i2ccfg);
-}
-
-static inline bool_t getpin_irq(void)
-{
-	return (!(palReadPad(GPIOC, 13)));
-}
-
-static void write_reg(uint8_t reg, uint8_t n, uint16_t val)
-{
-	uint8_t txbuf[3];
-
-	i2cAcquireBus(&I2CD1);
-
-	txbuf[0] = reg;
-
-	if (n == 1) {
-		txbuf[1] = val;
-		i2cMasterTransmitTimeout(&I2CD1, STMPE811_ADDR, txbuf, 2, NULL, 0, MS2ST(STMPE811_TIMEOUT));
-	} else if (n == 2) {
-		txbuf[1] = ((val & 0xFF00) >> 8);
-		txbuf[2] = (val & 0x00FF);
-		i2cMasterTransmitTimeout(&I2CD1, STMPE811_ADDR, txbuf, 3, NULL, 0, MS2ST(STMPE811_TIMEOUT));
-	}
-	
-	i2cReleaseBus(&I2CD1);
-}
- 
-static uint16_t read_reg(uint8_t reg, uint8_t n)
-{
-	uint8_t txbuf[1], rxbuf[2];
-	uint16_t ret;
-
-	rxbuf[0] = 0;
-	rxbuf[1] = 0;
-
-	i2cAcquireBus(&I2CD1);
-
-	txbuf[0] = reg;
-	i2cMasterTransmitTimeout(&I2CD1, STMPE811_ADDR, txbuf, 1, rxbuf, n, MS2ST(STMPE811_TIMEOUT));
-
-	if (n == 1) {
-		ret = rxbuf[0];
-	} else if (n == 2) {
-		ret = ((rxbuf[0] << 8) | (rxbuf[1] & 0xFF));
-	}
-
-	i2cReleaseBus(&I2CD1);
-
-	return ret;
-}
-
-static void read_reg_n(uint8_t reg, uint8_t n, uint8_t *rxbuf)
-{
-	uint8_t txbuf[1];
-
-	i2cAcquireBus(&I2CD1);
-
-	txbuf[0] = reg;
-	i2cMasterTransmitTimeout(&I2CD1, STMPE811_ADDR, txbuf, 1, rxbuf, n, MS2ST(STMPE811_TIMEOUT));
-
-	i2cReleaseBus(&I2CD1);
-}
-
-#endif /* _GINPUT_LLD_MOUSE_BOARD_H */
-
diff --git a/boards/base/FireBull-STM32F103-FB/board_SSD1289_firebullstm32f103.h b/boards/base/FireBull-STM32F103-FB/board_SSD1289_firebullstm32f103.h
deleted file mode 100644
index 99001e07..00000000
--- a/boards/base/FireBull-STM32F103-FB/board_SSD1289_firebullstm32f103.h
+++ /dev/null
@@ -1,124 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-#ifndef _GDISP_LLD_BOARD_H
-#define _GDISP_LLD_BOARD_H
-
-// For a multiple display configuration we would put all this in a structure and then
-//	set g->board to that structure.
-#define SET_CS		palSetPad(GPIOD, 12);
-#define CLR_CS		palClearPad(GPIOD, 12);
-#define SET_RS		palSetPad(GPIOD, 13);
-#define CLR_RS		palClearPad(GPIOD, 13);
-#define SET_WR		palSetPad(GPIOD, 14);
-#define CLR_WR		palClearPad(GPIOD, 14);
-#define SET_RD		palSetPad(GPIOD, 15);
-#define CLR_RD		palClearPad(GPIOD, 15);
-
-static inline void init_board(GDisplay *g)
-{
-
-	// As we are not using multiple displays we set g->board to NULL as we don't use it.
-	g->board = 0;
-
-	switch(g->controllerdisplay) {
-	case 0:											// Set up for Display 0
-		palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 12, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 13, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 14, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 15, PAL_MODE_OUTPUT_PUSHPULL);
-
-		// Configure the pins to a well know state
-		SET_RS;
-		SET_RD;
-		SET_WR;
-		CLR_CS;
-
-		break;
-	}
-}
-
-static inline void post_init_board(GDisplay *g)
-{
-	(void) g;
-}
-
-static inline void setpin_reset(GDisplay *g, bool_t state)
-{
-	(void) g;
-	(void) state;
-
-	/* Nothing to do here - reset pin tied to Vcc */
-}
-
-static inline void set_backlight(GDisplay *g, uint8_t percent)
-{
-	(void) g;
-	(void) percent;
-
-	/* Nothing to do here - Backlight always on */
-}
-
-static inline void acquire_bus(GDisplay *g)
-{
-	(void) g;
-}
-
-static inline void release_bus(GDisplay *g)
-{
-	(void) g;
-}
-
-static inline void write_index(GDisplay *g, uint16_t index)
-{
-	(void) g;
-
-	palWritePort(GPIOE, index);
-	CLR_RS;
-	CLR_WR;
-	SET_WR;
-	SET_RS;
-}
-
-static inline void write_data(GDisplay *g, uint16_t data)
-{
-	(void) g;
-
-	palWritePort(GPIOE, data);
-	CLR_WR;
-	SET_WR;
-}
-
-static inline void setreadmode(GDisplay *g)
-{
-	(void) g;
-
-	// change pin mode to digital input
-	palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_INPUT);
-	CLR_RD;
-}
-
-static inline void setwritemode(GDisplay *g)
-{
-	(void) g;
-	
-	// change pin mode back to digital output
-	SET_RD;
-	palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
-}
-
-static inline uint16_t read_data(GDisplay *g) {
-	return palReadPort(GPIOE);
-}
-
-#if defined(GDISP_USE_DMA)
-	#error "GDISP - SSD1289: The GPIO interface does not support DMA"
-#endif
-
-#endif /* _GDISP_LLD_BOARD_H */
-
diff --git a/boards/base/FireBull-STM32F103-FB/ginput_lld_mouse_board_firebull_stm32f103.h b/boards/base/FireBull-STM32F103-FB/ginput_lld_mouse_board_firebull_stm32f103.h
deleted file mode 100644
index 102bd834..00000000
--- a/boards/base/FireBull-STM32F103-FB/ginput_lld_mouse_board_firebull_stm32f103.h
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-#ifndef _GINPUT_LLD_MOUSE_BOARD_H
-#define _GINPUT_LLD_MOUSE_BOARD_H
-
-static const SPIConfig spicfg = { 
-    NULL,
-	GPIOC, 
-    6,
-    /* SPI_CR1_BR_2 |*/ SPI_CR1_BR_1 | SPI_CR1_BR_0,
-};
-
-static inline void init_board(void)
-{
-	spiStart(&SPID1, &spicfg);
-}
-
-static inline bool_t getpin_pressed(void)
-{
-	return (!palReadPad(GPIOC, 4));
-}
-
-static inline void aquire_bus(void)
-{
-	spiAcquireBus(&SPID1);
-    palClearPad(GPIOC, 6);
-}
-
-static inline void release_bus(void)
-{
-	palSetPad(GPIOC, 6);
-	spiReleaseBus(&SPID1);
-}
-
-static inline uint16_t read_value(uint16_t port)
-{
-    static uint8_t txbuf[3] = {0};
-    static uint8_t rxbuf[3] = {0};
-    uint16_t ret;
-
-    txbuf[0] = port;
-
-    spiExchange(&SPID1, 3, txbuf, rxbuf);
-
-    ret = (rxbuf[1] << 5) | (rxbuf[2] >> 3); 
-    
-	return ret;
-}
-
-#endif /* _GINPUT_LLD_MOUSE_BOARD_H */
-
diff --git a/boards/base/Marlin/board_RA8875_marlin.h b/boards/base/Marlin/board_RA8875_marlin.h
deleted file mode 100644
index b1d55a92..00000000
--- a/boards/base/Marlin/board_RA8875_marlin.h
+++ /dev/null
@@ -1,113 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/gdisp/RA8875/board_RA8875_marlin.h
- * @brief   GDISP Graphic Driver subsystem board interface for the RA8875 display.
- */
-
-#ifndef _BOARD_RA8875_H
-#define _BOARD_RA8875_H
-
-// For a multiple display configuration we would put all this in a structure and then
-// set g->board to that structure.
-#define GDISP_RAM              (*((volatile uint16_t *) 0x68000000)) /* RS = 0 */
-#define GDISP_REG              (*((volatile uint16_t *) 0x68020000)) /* RS = 1 */
-#define FSMC_BANK				4
-
-
-static inline void init_board(GDisplay *g) {
-	// As we are not using multiple displays we set g->board to NULL as we don't use it.
-	g->board = 0;
-
-	switch(g->controllerdisplay) {
-		// setup for display 0
-		case 0: {		
-
-			// enable the FSMC peripheral
-			rccEnableAHB3(RCC_AHB3ENR_FSMCEN, 0);
-
-			// setup the pin modes for FSMC
-			IOBus busD = {GPIOD, (1 << 0) | (1 << 1) | (1 << 4) | (1 << 5) | (1 << 8) |
-									(1 << 9) | (1 << 10) | (1 << 11) | (1 << 14) | (1 << 15), 0};
-
-			IOBus busE = {GPIOE, (1 << 7) | (1 << 8) | (1 << 9) | (1 << 10) | (1 << 11) | (1 << 12) |
-								(1 << 13) | (1 << 14) | (1 << 15), 0};
-
-			IOBus busG = {GPIOG, (1 << 10), 0};
-
-			palSetBusMode(&busD, PAL_MODE_ALTERNATE(12));
-			palSetBusMode(&busE, PAL_MODE_ALTERNATE(12));
-			palSetBusMode(&busG, PAL_MODE_ALTERNATE(12));
-
-			// FSMC timing
-			FSMC_Bank1->BTCR[FSMC_BANK+1] = (FSMC_BTR1_ADDSET_1 | FSMC_BTR1_ADDSET_3) \
-					| (FSMC_BTR1_DATAST_1 | FSMC_BTR1_DATAST_3) \
-					| (FSMC_BTR1_BUSTURN_1 | FSMC_BTR1_BUSTURN_3) ;
-
-			// Bank1 NOR/SRAM control register configuration
-			// This is actually not needed as already set by default after reset
-			FSMC_Bank1->BTCR[FSMC_BANK] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
-
-			break;
-		}
-
-		// marlin does not have any secondary display so far
-		default:
-			break;
-	}
-}
-
-static inline void post_init_board(GDisplay *g) {
-	(void) g;
-	
-	// FSMC delay reduced as the controller now runs at full speed
-	FSMC_Bank1->BTCR[2+1] = FSMC_BTR1_ADDSET_0 | FSMC_BTR1_DATAST_2 | FSMC_BTR1_BUSTURN_0 ;
-	FSMC_Bank1->BTCR[2] = FSMC_BCR1_MWID_0 | FSMC_BCR1_WREN | FSMC_BCR1_MBKEN;
-}
-
-static inline void setpin_reset(GDisplay *g, bool_t state) {
-	(void) g;
-	(void) state;
-}
-
-static inline void acquire_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void release_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void write_index(GDisplay *g, uint16_t index) {
-	(void) g;
-
-	GDISP_REG = index;
-}
-
-static inline void write_data(GDisplay *g, uint16_t data) {
-	(void) g;
-
-	GDISP_RAM = data;
-}
-
-static inline void setreadmode(GDisplay *g) {
-	(void) g;
-}
-
-static inline void setwritemode(GDisplay *g) {
-	(void) g;
-}
-
-static inline uint16_t read_data(GDisplay *g) {
-	(void) g;
-
-	return GDISP_RAM;
-}
-
-#endif /* _BOARD_RA8875_H */
-
diff --git a/boards/base/Marlin/ginput_lld_mouse_board_marlin.h b/boards/base/Marlin/ginput_lld_mouse_board_marlin.h
deleted file mode 100644
index e3e18c24..00000000
--- a/boards/base/Marlin/ginput_lld_mouse_board_marlin.h
+++ /dev/null
@@ -1,111 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/ginput/touch/FT5x06/ginput_lld_mouse_board_marlin.h
- * @brief   GINPUT Touch low level driver source for the FT5x06.
- *
- * @defgroup Mouse Mouse
- * @ingroup GINPUT
- * @{
- */
-
-#ifndef _GINPUT_LLD_MOUSE_BOARD_H
-#define _GINPUT_LLD_MOUSE_BOARD_H
-
-/* I2C interface #2 - Touchscreen controller */
-static const I2CConfig i2ccfg2 = {
-    OPMODE_I2C,
-    400000,
-    FAST_DUTY_CYCLE_2,
-};
-
-/**
- * @brief   Initialise the board for the touch.
- *
- * @notapi
- */
-static void init_board(void) {
-
-}
-
-
-/**
- * @brief	Write a value into a certain register
- *
- * @param[in] reg	The register address
- * @param[in] n		The amount of bytes (one or two)
- * @param[in] val	The value
- *
- * @notapi
- */
-static void write_reg(uint8_t reg, uint8_t n, uint16_t val) {
-	uint8_t txbuf[3];
-
-	i2cAcquireBus(&I2CD2);
-
-	txbuf[0] = reg;
-
-	if (n == 1) {
-		txbuf[1] = val;
-		i2cMasterTransmitTimeout(&I2CD2, FT5x06_ADDR, txbuf, 2, NULL, 0, MS2ST(FT5x06_TIMEOUT));
-	} else if (n == 2) {
-		txbuf[1] = ((val & 0xFF00) >> 8);
-		txbuf[2] = (val & 0x00FF);
-		i2cMasterTransmitTimeout(&I2CD2, FT5x06_ADDR, txbuf, 3, NULL, 0, MS2ST(FT5x06_TIMEOUT));
-	}
-	
-	i2cReleaseBus(&I2CD2);
-}
- 
-/**
- * @brief	Read the value of a certain register
- *
- * @param[in] reg	The register address
- * @param[in] n		The amount of bytes (one or two)
- *
- * @return Data read from device (one byte or two depending on n param)
- *
- * @notapi
- */
-static uint16_t read_reg(uint8_t reg, uint8_t n) {
-	uint8_t txbuf[1], rxbuf[2];
-	uint16_t ret;
-
-	rxbuf[0] = 0;
-	rxbuf[1] = 0;
-
-	i2cAcquireBus(&I2CD2);
-
-	txbuf[0] = reg;
-	i2cMasterTransmitTimeout(&I2CD2, FT5x06_ADDR, txbuf, 1, rxbuf, n, MS2ST(FT5x06_TIMEOUT));
-
-	if (n == 1) {
-		ret = rxbuf[0];
-	} else if (n == 2) {
-		ret = ((rxbuf[0] << 8) | (rxbuf[1] & 0xFF));
-	}
-
-	i2cReleaseBus(&I2CD2);
-
-	return ret;
-}
-
-static void read_reg_n(uint8_t reg, uint8_t n, uint8_t *rxbuf) {
-	uint8_t txbuf[1];
-
-	i2cAcquireBus(&I2CD2);
-
-	txbuf[0] = reg;
-	i2cMasterTransmitTimeout(&I2CD2, FT5x06_ADDR, txbuf, 1, rxbuf, n, MS2ST(FT5x06_TIMEOUT));
-
-	i2cReleaseBus(&I2CD2);
-}
-
-#endif /* _GINPUT_LLD_MOUSE_BOARD_H */
-/** @} */
-