1 files changed, 0 insertions, 108 deletions
diff --git a/boards/addons/gdisp/board_SSD1289_firebullstm32f103.h b/boards/addons/gdisp/board_SSD1289_firebullstm32f103.h
deleted file mode 100644
index 99d37299..00000000
--- a/boards/addons/gdisp/board_SSD1289_firebullstm32f103.h
+++ /dev/null
@@ -1,108 +0,0 @@
-/*
- * This file is subject to the terms of the GFX License. If a copy of
- * the license was not distributed with this file, you can obtain one at:
- *
- *              http://ugfx.org/license.html
- */
-
-/**
- * @file    drivers/gdisp/SSD1289/board_SSD1289_firebullstm32f103.h
- * @brief   GDISP Graphic Driver subsystem board interface for the SSD1289 display.
- */
-
-#ifndef _GDISP_LLD_BOARD_H
-#define _GDISP_LLD_BOARD_H
-
-// For a multiple display configuration we would put all this in a structure and then
-//	set g->board to that structure.
-#define SET_CS		palSetPad(GPIOD, 12);
-#define CLR_CS		palClearPad(GPIOD, 12);
-#define SET_RS		palSetPad(GPIOD, 13);
-#define CLR_RS		palClearPad(GPIOD, 13);
-#define SET_WR		palSetPad(GPIOD, 14);
-#define CLR_WR		palClearPad(GPIOD, 14);
-#define SET_RD		palSetPad(GPIOD, 15);
-#define CLR_RD		palClearPad(GPIOD, 15);
-
-static inline void init_board(GDisplay *g) {
-
-	// As we are not using multiple displays we set g->board to NULL as we don't use it.
-	g->board = 0;
-
-	switch(g->controllerdisplay) {
-	case 0:											// Set up for Display 0
-		palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 12, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 13, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 14, PAL_MODE_OUTPUT_PUSHPULL);
-		palSetPadMode(GPIOD, 15, PAL_MODE_OUTPUT_PUSHPULL);
-
-		// Configure the pins to a well know state
-		SET_RS;
-		SET_RD;
-		SET_WR;
-		CLR_CS;
-		break;
-	}
-}
-
-static inline void post_init_board(GDisplay *g) {
-	(void) g;
-}
-
-static inline void setpin_reset(GDisplay *g, bool_t state) {
-	(void) g;
-	(void) state;
-	/* Nothing to do here - reset pin tied to Vcc */
-}
-
-static inline void set_backlight(GDisplay *g, uint8_t percent) {
-	(void) g;
-	(void) percent;
-	/* Nothing to do here - Backlight always on */
-}
-
-static inline void acquire_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void release_bus(GDisplay *g) {
-	(void) g;
-}
-
-static inline void write_index(GDisplay *g, uint16_t index) {
-	(void) g;
-	palWritePort(GPIOE, index);
-	CLR_RS; CLR_WR; SET_WR; SET_RS;
-}
-
-static inline void write_data(GDisplay *g, uint16_t data) {
-	(void) g;
-	palWritePort(GPIOE, data);
-	CLR_WR; SET_WR;
-}
-
-static inline void setreadmode(GDisplay *g) {
-	(void) g;
-	// change pin mode to digital input
-	palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_INPUT);
-	CLR_RD;
-}
-
-static inline void setwritemode(GDisplay *g) {
-	(void) g;
-	// change pin mode back to digital output
-	SET_RD;
-	palSetGroupMode(GPIOE, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
-}
-
-static inline uint16_t read_data(GDisplay *g) {
-	return palReadPort(GPIOE);
-}
-
-#if defined(GDISP_USE_DMA)
-	#error "GDISP - SSD1289: The GPIO interface does not support DMA"
-#endif
-
-#endif /* _GDISP_LLD_BOARD_H */
-