1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
|
/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.org/license.html
*/
/**
* @file drivers/gdisp/HX8347D/gdisp_lld_board_st_stm32f4_discovery.h
* @brief GDISP Graphic Driver subsystem board SPI interface for the HX8347D display.
*
* @addtogroup GDISP
* @{
*/
#ifndef _GDISP_LLD_BOARD_H
#define _GDISP_LLD_BOARD_H
#define SET_RST palSetPad(GPIOB, 8);
#define CLR_RST palClearPad(GPIOB, 8);
/* PWM configuration structure. We use timer 4 channel 2 (orange LED on board). */
static const PWMConfig pwmcfg = {
1000000, /* 1 MHz PWM clock frequency. */
100, /* PWM period is 100 cycles. */
NULL,
{
{PWM_OUTPUT_ACTIVE_HIGH, NULL},
{PWM_OUTPUT_ACTIVE_HIGH, NULL},
{PWM_OUTPUT_ACTIVE_HIGH, NULL},
{PWM_OUTPUT_ACTIVE_HIGH, NULL}
},
0
};
/*
* SPI1 configuration structure.
* Speed 42MHz, CPHA=0, CPOL=0, 8bits frames, MSb transmitted first.
* The slave select line is the pin 4 on the port GPIOA.
*/
static const SPIConfig spi1cfg1 = {
NULL,
/* HW dependent part.*/
GPIOA,
4,
0 //SPI_CR1_BR_0
};
/*
* SPI1 configuration structure.
* Speed 42MHz, CPHA=0, CPOL=0, 16bits frames, MSb transmitted first.
* The slave select line is the pin 4 on the port GPIOA.
*/
static const SPIConfig spi1cfg2 = {
NULL,
/* HW dependent part.*/
GPIOA,
4,
SPI_CR1_DFF //SPI_CR1_BR_0
};
/**
* @brief Initialise the board for the display.
* @notes This board definition uses GPIO and assumes exclusive access to these GPIO pins
*
* @notapi
*/
static inline void init_board(void) {
/* Display backlight control */
/* TIM4 is an alternate function 2 (AF2) */
pwmStart(&PWMD4, &pwmcfg);
palSetPadMode(GPIOD, 13, PAL_MODE_ALTERNATE(2));
pwmEnableChannel(&PWMD4, 1, 100);
palSetPadMode(GPIOB, 8, PAL_MODE_OUTPUT_PUSHPULL |
PAL_STM32_OSPEED_HIGHEST); /* RST */
palSetPadMode(GPIOB, 9, PAL_MODE_OUTPUT_PUSHPULL |
PAL_STM32_OSPEED_HIGHEST); /* RS */
/*
* Initializes the SPI driver 1. The SPI1 signals are routed as follow:
* PB12 - NSS.
* PB13 - SCK.
* PB14 - MISO.
* PB15 - MOSI.
*/
spiStart(&SPID1, &spi1cfg1);
palSetPad(GPIOA, 4);
palSetPadMode(GPIOA, 4, PAL_MODE_OUTPUT_PUSHPULL |
PAL_STM32_OSPEED_HIGHEST); /* NSS. */
palSetPadMode(GPIOA, 5, PAL_MODE_ALTERNATE(5) |
PAL_STM32_OSPEED_HIGHEST); /* SCK. */
palSetPadMode(GPIOA, 6, PAL_MODE_ALTERNATE(5)); /* MISO. */
palSetPadMode(GPIOA, 7, PAL_MODE_ALTERNATE(5) |
PAL_STM32_OSPEED_HIGHEST); /* MOSI. */
}
/**
* @brief Set or clear the lcd reset pin.
*
* @param[in] state TRUE = lcd in reset, FALSE = normal operation
*
* @notapi
*/
static inline void setpin_reset(bool_t state) {
if (state) {
CLR_RST;
} else {
SET_RST;
}
}
/**
* @brief Set the lcd back-light level.
*
* @param[in] percent 0 to 100%
*
* @notapi
*/
static inline void set_backlight(uint8_t percent) {
pwmEnableChannel(&PWMD4, 1, percent);
}
/**
* @brief Take exclusive control of the bus
* @note Not needed, not implemented
*
* @notapi
*/
static inline void acquire_bus(void) {
spiAcquireBus(&SPID1);
}
/**
* @brief Release exclusive control of the bus
* @note Not needed, not implemented
*
* @notapi
*/
static inline void release_bus(void) {
spiReleaseBus(&SPID1);
}
/**
* @brief Send data to the index register.
*
* @param[in] index The index register to set
*
* @notapi
*/
static inline void write_index(uint8_t cmd) {
palClearPad(GPIOB, 9);
palClearPad(GPIOA, 4);
while((SPI1->SR & SPI_SR_TXE) == 0);
SPI1->DR = cmd;
while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0));
palSetPad(GPIOB, 9);
}
/**
* @brief Send data to the lcd.
*
* @param[in] data The data to send
*
* @notapi
*/
static inline void write_data(uint8_t data) {
SPI1->DR = data;
while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0));
palSetPad(GPIOA, 4);
}
static inline void write_ram8(uint8_t data1, uint8_t data2) {
SPI1->DR = data1;
while((SPI1->SR & SPI_SR_TXE) == 0);
SPI1->DR = data2;
while(((SPI1->SR & SPI_SR_TXE) == 0) || ((SPI1->SR & SPI_SR_BSY) != 0));
palSetPad(GPIOA, 4);
}
static inline void write_ram16(uint16_t data) {
while((SPI1->SR & SPI_SR_TXE) == 0);
SPI1->DR = data;
}
#if GDISP_HARDWARE_READPIXEL || defined(__DOXYGEN__)
/**
* @brief Read data from the lcd.
*
* @return The data from the lcd
* @note The chip select may need to be asserted/de-asserted
* around the actual spi read
*
* @notapi
*/
static inline uint16_t read_data(void) {
}
#endif
#endif /* _GDISP_LLD_BOARD_H */
/** @} */
|
