1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
|
/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.io/license.html
*/
#include "gfx.h"
#if GFX_USE_GDISP
/* This controller is only ever used with a 240 x 320 display */
#if defined(GDISP_SCREEN_HEIGHT) || defined(GDISP_SCREEN_HEIGHT)
#if GFX_COMPILER_WARNING_TYPE == GFX_COMPILER_WARNING_DIRECT
#warning "GDISP: This low level driver does not support setting a screen size. It is being ignored."
#elif GFX_COMPILER_WARNING_TYPE == GFX_COMPILER_WARNING_MACRO
COMPILER_WARNING("GDISP: This low level driver does not support setting a screen size. It is being ignored.")
#endif
#undef GDISP_SCREEN_WIDTH
#undef GDISP_SCREEN_HEIGHT
#endif
#define GDISP_DRIVER_VMT GDISPVMT_ILI9320
#include "gdisp_lld_config.h"
#include "../../../src/gdisp/gdisp_driver.h"
#include "board_ILI9320.h"
/*===========================================================================*/
/* Driver local definitions. */
/*===========================================================================*/
#ifndef GDISP_SCREEN_HEIGHT
#define GDISP_SCREEN_HEIGHT 320
#endif
#ifndef GDISP_SCREEN_WIDTH
#define GDISP_SCREEN_WIDTH 240
#endif
#ifndef GDISP_INITIAL_CONTRAST
#define GDISP_INITIAL_CONTRAST 50
#endif
#ifndef GDISP_INITIAL_BACKLIGHT
#define GDISP_INITIAL_BACKLIGHT 100
#endif
/*===========================================================================*/
/* Driver local variables. */
/*===========================================================================*/
/*===========================================================================*/
/* Driver local functions. */
/*===========================================================================*/
#define dummy_read(g) { volatile uint16_t dummy; dummy = read_data(g); (void) dummy; }
#define write_reg(g, reg, data) { write_index(g, reg); write_data(g, data); }
static void set_cursor(GDisplay *g) {
switch(g->g.Orientation) {
default:
case gOrientation0:
case gOrientation180:
write_reg(g, 0x20, g->p.x);
write_reg(g, 0x21, g->p.y);
break;
case gOrientation90:
case gOrientation270:
write_reg(g, 0x20, g->p.y);
write_reg(g, 0x21, g->p.x);
break;
}
write_index(g, 0x22);
}
static void set_viewport(GDisplay *g) {
switch(g->g.Orientation) {
default:
case gOrientation0:
case gOrientation180:
write_reg(g, 0x50, g->p.x);
write_reg(g, 0x51, g->p.x + g->p.cx - 1);
write_reg(g, 0x52, g->p.y);
write_reg(g, 0x53, g->p.y + g->p.cy - 1);
break;
case gOrientation90:
case gOrientation270:
write_reg(g, 0x50, g->p.y);
write_reg(g, 0x51, g->p.y + g->p.cy - 1);
write_reg(g, 0x52, g->p.x);
write_reg(g, 0x53, g->p.x + g->p.cx - 1);
break;
}
}
LLDSPEC gBool gdisp_lld_init(GDisplay *g) {
uint16_t cver;
// No private area for this controller
g->priv = 0;
// Initialise the board interface
init_board(g);
/* Hardware reset */
setpin_reset(g, gTrue);
gfxSleepMicroseconds(1000);
setpin_reset(g, gFalse);
gfxSleepMicroseconds(1000);
acquire_bus(g);
write_index(g, 0); // Get controller version
setreadmode(g);
dummy_read(g);
cver = read_data(g);
setwritemode(g);
write_reg(g, 0x00, 0x0001); //start Int. osc
gfxSleepMicroseconds(500);
write_reg(g, 0x01, 0x0100); //Set SS bit (shift direction of outputs is from S720 to S1)
write_reg(g, 0x02, 0x0700); //select the line inversion
write_reg(g, 0x03, 0x1038); //Entry mode(Horizontal : increment,Vertical : increment, AM=1)
write_reg(g, 0x04, 0x0000); //Resize control(No resizing)
write_reg(g, 0x08, 0x0202); //front and back porch 2 lines
write_reg(g, 0x09, 0x0000); //select normal scan
write_reg(g, 0x0A, 0x0000); //display control 4
write_reg(g, 0x0C, 0x0000); //system interface(2 transfer /pixel), internal sys clock,
write_reg(g, 0x0D, 0x0000); //Frame marker position
write_reg(g, 0x0F, 0x0000); //selects clk, enable and sync signal polarity,
write_reg(g, 0x10, 0x0000); //
write_reg(g, 0x11, 0x0000); //power control 2 reference voltages = 1:1,
write_reg(g, 0x12, 0x0000); //power control 3 VRH
write_reg(g, 0x13, 0x0000); //power control 4 VCOM amplitude
gfxSleepMicroseconds(500);
write_reg(g, 0x10, 0x17B0); //power control 1 BT,AP
write_reg(g, 0x11, 0x0137); //power control 2 DC,VC
gfxSleepMicroseconds(500);
write_reg(g, 0x12, 0x0139); //power control 3 VRH
gfxSleepMicroseconds(500);
write_reg(g, 0x13, 0x1d00); //power control 4 vcom amplitude
write_reg(g, 0x29, 0x0011); //power control 7 VCOMH
gfxSleepMicroseconds(500);
write_reg(g, 0x30, 0x0007);
write_reg(g, 0x31, 0x0403);
write_reg(g, 0x32, 0x0404);
write_reg(g, 0x35, 0x0002);
write_reg(g, 0x36, 0x0707);
write_reg(g, 0x37, 0x0606);
write_reg(g, 0x38, 0x0106);
write_reg(g, 0x39, 0x0007);
write_reg(g, 0x3c, 0x0700);
write_reg(g, 0x3d, 0x0707);
write_reg(g, 0x20, 0x0000); //starting Horizontal GRAM Address
write_reg(g, 0x21, 0x0000); //starting Vertical GRAM Address
write_reg(g, 0x50, 0x0000); //Horizontal GRAM Start Position
write_reg(g, 0x51, 0x00EF); //Horizontal GRAM end Position
write_reg(g, 0x52, 0x0000); //Vertical GRAM Start Position
write_reg(g, 0x53, 0x013F); //Vertical GRAM end Position
switch (cver) {
case 0x9320:
write_reg(g, 0x60, 0x2700); //starts scanning from G1, and 320 drive lines
break;
case 0x9325:
write_reg(g, 0x60, 0xA700); //starts scanning from G1, and 320 drive lines
break;
}
write_reg(g, 0x61, 0x0001); //fixed base display
write_reg(g, 0x6a, 0x0000); //no scroll
write_reg(g, 0x90, 0x0010); //set Clocks/Line =16, Internal Operation Clock Frequency=fosc/1,
write_reg(g, 0x92, 0x0000); //set gate output non-overlap period=0
write_reg(g, 0x93, 0x0003); //set Source Output Position=3
write_reg(g, 0x95, 0x0110); //RGB interface(Clocks per line period=16 clocks)
write_reg(g, 0x97, 0x0110); //set Gate Non-overlap Period 0 locksc
write_reg(g, 0x98, 0x0110); //
write_reg(g, 0x07, 0x0173); //display On
// Finish Init
post_init_board(g);
// Release the bus
release_bus(g);
// Turn on the backlight
set_backlight(g, GDISP_INITIAL_BACKLIGHT);
/* Initialise the GDISP structure */
g->g.Width = GDISP_SCREEN_WIDTH;
g->g.Height = GDISP_SCREEN_HEIGHT;
g->g.Orientation = gOrientation0;
g->g.Powermode = gPowerOn;
g->g.Backlight = GDISP_INITIAL_BACKLIGHT;
g->g.Contrast = GDISP_INITIAL_CONTRAST;
return gTrue;
}
#if GDISP_HARDWARE_STREAM_WRITE
LLDSPEC void gdisp_lld_write_start(GDisplay *g) {
acquire_bus(g);
set_viewport(g);
#if !GDISP_HARDWARE_STREAM_POS
set_cursor(g);
#endif
}
LLDSPEC void gdisp_lld_write_color(GDisplay *g) {
write_data(g, gdispColor2Native(g->p.color));
}
LLDSPEC void gdisp_lld_write_stop(GDisplay *g) {
release_bus(g);
}
#if GDISP_HARDWARE_STREAM_POS
LLDSPEC void gdisp_lld_write_pos(GDisplay *g) {
set_cursor(g);
}
#endif
#endif
#if GDISP_HARDWARE_STREAM_READ
LLDSPEC void gdisp_lld_read_start(GDisplay *g) {
acquire_bus(g);
set_viewport(g);
set_cursor(g);
setreadmode(g);
dummy_read(g);
}
LLDSPEC gColor gdisp_lld_read_color(GDisplay *g) {
uint16_t data;
data = read_data(g);
return gdispNative2Color(data);
}
LLDSPEC void gdisp_lld_read_stop(GDisplay *g) {
setwritemode(g);
release_bus(g);
}
#endif
#if GDISP_NEED_CONTROL && GDISP_HARDWARE_CONTROL
LLDSPEC void gdisp_lld_control(GDisplay *g) {
switch(g->p.x) {
case GDISP_CONTROL_POWER:
if (g->g.Powermode == (gPowermode)g->p.ptr)
return;
switch((gPowermode)g->p.ptr) {
case gPowerOff:
acquire_bus(g);
write_reg(g, 0x07, 0x0000);
write_reg(g, 0x10, 0x0000);
write_reg(g, 0x11, 0x0000);
write_reg(g, 0x12, 0x0000);
write_reg(g, 0x13, 0x0000);
release_bus(g);
set_backlight(g, 0);
break;
case gPowerOn:
//*************Power On sequence ******************//
acquire_bus(g);
write_reg(g, 0x10, 0x0000); /* SAP, BT[3:0], AP, DSTB, SLP, STB */
write_reg(g, 0x11, 0x0000); /* DC1[2:0], DC0[2:0], VC[2:0] */
write_reg(g, 0x12, 0x0000); /* VREG1OUT voltage */
write_reg(g, 0x13, 0x0000); /* VDV[4:0] for VCOM amplitude */
gfxSleepMicroseconds(2000); /* Dis-charge capacitor power voltage */
write_reg(g, 0x10, 0x17B0); /* SAP, BT[3:0], AP, DSTB, SLP, STB */
write_reg(g, 0x11, 0x0147); /* DC1[2:0], DC0[2:0], VC[2:0] */
gfxSleepMicroseconds(500);
write_reg(g, 0x12, 0x013C); /* VREG1OUT voltage */
gfxSleepMicroseconds(500);
write_reg(g, 0x13, 0x0E00); /* VDV[4:0] for VCOM amplitude */
write_reg(g, 0x29, 0x0009); /* VCM[4:0] for VCOMH */
gfxSleepMicroseconds(500);
write_reg(g, 0x07, 0x0173); /* 262K color and display ON */
release_bus(g);
set_backlight(g, g->g.Backlight);
break;
case gPowerSleep:
acquire_bus(g);
write_reg(g, 0x07, 0x0000); /* display OFF */
write_reg(g, 0x10, 0x0000); /* SAP, BT[3:0], APE, AP, DSTB, SLP */
write_reg(g, 0x11, 0x0000); /* DC1[2:0], DC0[2:0], VC[2:0] */
write_reg(g, 0x12, 0x0000); /* VREG1OUT voltage */
write_reg(g, 0x13, 0x0000); /* VDV[4:0] for VCOM amplitude */
gfxSleepMicroseconds(2000); /* Dis-charge capacitor power voltage */
write_reg(g, 0x10, 0x0002); /* SAP, BT[3:0], APE, AP, DSTB, SLP */
release_bus(g);
set_backlight(g, 0);
break;
case gPowerDeepSleep:
acquire_bus(g);
write_reg(g, 0x07, 0x0000); /* display OFF */
write_reg(g, 0x10, 0x0000); /* SAP, BT[3:0], APE, AP, DSTB, SLP */
write_reg(g, 0x11, 0x0000); /* DC1[2:0], DC0[2:0], VC[2:0] */
write_reg(g, 0x12, 0x0000); /* VREG1OUT voltage */
write_reg(g, 0x13, 0x0000); /* VDV[4:0] for VCOM amplitude */
gfxSleepMicroseconds(2000); /* Dis-charge capacitor power voltage */
write_reg(g, 0x10, 0x0004); /* SAP, BT[3:0], APE, AP, DSTB, SLP */
release_bus(g);
set_backlight(g, 0);
break;
default:
return;
}
g->g.Powermode = (gPowermode)g->p.ptr;
return;
case GDISP_CONTROL_ORIENTATION:
if (g->g.Orientation == (gOrientation)g->p.ptr)
return;
switch((gOrientation)g->p.ptr) {
case gOrientation0:
acquire_bus(g);
write_reg(g, 0x01, 0x0100);
write_reg(g, 0x03, 0x1038);
write_reg(g, 0x60, 0x2700);
release_bus(g);
g->g.Height = GDISP_SCREEN_HEIGHT;
g->g.Width = GDISP_SCREEN_WIDTH;
break;
case gOrientation90:
acquire_bus(g);
write_reg(g, 0x01, 0x0000);
write_reg(g, 0x03, 0x1030);
write_reg(g, 0x60, 0x2700);
release_bus(g);
g->g.Height = GDISP_SCREEN_WIDTH;
g->g.Width = GDISP_SCREEN_HEIGHT;
break;
case gOrientation180:
acquire_bus(g);
write_reg(g, 0x01, 0x0000);
write_reg(g, 0x03, 0x1030);
write_reg(g, 0x60, 0x2700);
release_bus(g);
g->g.Height = GDISP_SCREEN_HEIGHT;
g->g.Width = GDISP_SCREEN_WIDTH;
break;
case gOrientation270:
acquire_bus(g);
write_reg(g, 0x01, 0x0100);
write_reg(g, 0x03, 0x1038);
write_reg(g, 0x60, 0xA700);
release_bus(g);
g->g.Height = GDISP_SCREEN_WIDTH;
g->g.Width = GDISP_SCREEN_HEIGHT;
break;
default:
return;
}
g->g.Orientation = (gOrientation)g->p.ptr;
return;
case GDISP_CONTROL_BACKLIGHT:
if ((unsigned)g->p.ptr > 100)
g->p.ptr = (void *)100;
set_backlight(g, (unsigned)g->p.ptr);
g->g.Backlight = (unsigned)g->p.ptr;
return;
default:
return;
}
}
#endif
#endif /* GFX_USE_GDISP */
|