1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
|
/*
* This file is subject to the terms of the GFX License. If a copy of
* the license was not distributed with this file, you can obtain one at:
*
* http://ugfx.org/license.html
*/
/**
* @file drivers/tdisp/HD44780/tdisp_lld_board_st_stm32f4_discovery.h
* @brief TDISP driver subsystem board interface for the HD44780 display
*
* @addtogroup TDISP
* @{
*/
#ifndef _TDISP_LLD_BOARD_H
#define _TDISP_LLD_BOARD_H
/* Configure these to match the hardware connections on your board */
#define BUS_4BITS TRUE
/* Configure the bitoffset in the dataport so they match with the
* hardware pins. An offset of 0 means bit0 stays at bit0 of the dataport.
* If the offset is set to 3, bit0 of the nibble will be positioned at
* P[A..G]3 of the hardware-port.
*/
#define hardware_offset 3
/* The port where the data is sent to. In the
* low-leveldriver het hardware_offset is taken
* into account. If for example the hardware_offset
* is set to 3, then de data will be sent to
* PE3, PE4, PE5 en PE6, if the dataport where GPIOE.
*/
#define PORT_DATA GPIOE
/* The port used to controle the controle lines of
* the display.
*/
#define PORT_CTRL GPIOD
/* Pin to controle the R/S-line of the display */
#define PIN_RS 0
/* Pin to controle the EN-line of the display */
#define PIN_EN 1
/* Pin to controle the R/W-pin of the display.
* If reading of the display is not used disable
* reading in the gfxconf.h and put a dummy value here
* as it will not be used.
*/
#define PIN_RW 7
static void init_board(void) {
/* Initialize the ports for data and controle-lines */
palSetGroupMode(PORT_CTRL, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
palSetGroupMode(PORT_DATA, PAL_WHOLE_PORT, 0, PAL_MODE_OUTPUT_PUSHPULL);
/* Set alle controle pins to low */
palClearPad(PORT_CTRL, PIN_RS);
palClearPad(PORT_CTRL, PIN_EN);
#if TDISP_NEED_READ
palClearPad(PORT_CTRL, PIN_RW);
#endif
}
/* This is the low-level routine for sending the bits
* to the LCD-display. This routine shifts
* the bits so they match the hardware port.
*/
static void writeToLCD(uint8_t data) {
palWritePort(PORT_DATA, data<<hardware_offset);
palSetPad(PORT_CTRL, PIN_EN);
gfxSleepMicroseconds(1);
palClearPad(PORT_CTRL, PIN_EN);
/* wait a little while so that de display can process the data */
gfxSleepMicroseconds(5);
}
/* Writes a command to the display. The
* RS-line is pulled low and than the
* data is send.
*/
static void write_cmd(uint8_t data) {
palClearPad(PORT_CTRL, PIN_RS);
#if BUS_4BITS
/* first send the high-nibble */
writeToLCD(data>>4);
#endif
/* send the low-nibble */
#if BUS_4BITS
/* in 4-bit mode the high-nibble is zeroed out */
writeToLCD(data & 0x0F);
#else
writeToLCD(data);
#endif
}
// static void write_initcmd(uint8_t data) {
// write_cmd(data);
// }
/* Write data to the display. The
* RS-line is pulled high and than the
* data is send.
*/
static void write_data(uint8_t data) {
palSetPad(PORT_CTRL, PIN_RS);
#if BUS_4BITS
/* first send the high-nibble */
writeToLCD(data>>4);
#endif
/* send the low-nibble */
#if BUS_4BITS
/* in 4-bit mode the high-nibble is zeroed out */
writeToLCD(data & 0x0F);
#else
writeToLCD(data);
#endif
}
#endif /* _TDISP_LLD_BOARD_H */
/** @} */
|
