Merge pull request #7 from YosysHQ/master

Syncing with official repo

2 files changed, 12 insertions, 6 deletions

diff --git a/techlibs/intel/cyclonev/cells_map.v b/techlibs/intel/cyclonev/cells_map.v
index bd60d4e17..f8d142bc9 100644
--- a/techlibs/intel/cyclonev/cells_map.v
+++ b/techlibs/intel/cyclonev/cells_map.v
@@ -76,7 +76,7 @@ module \$lut (A, Y);
    wire              VCC;
    wire              GND;
    assign {VCC,GND} = {1'b1,1'b0};
-   
+
    generate
       if (WIDTH == 1) begin
 	 assign Y = ~A[0]; // Not need to spend 1 logic cell for such an easy function
@@ -151,7 +151,7 @@ module \$lut (A, Y);
                     TODO: There's not a just 7-input function on Cyclone V, see the following note:
                     **Extended LUT Mode**
                     Use extended LUT mode to implement a specific set of 7-input functions. The set must
-                    be a 2-to-1 multiplexer fed by two arbitrary 5-input functions sharing four inputs. 
+                    be a 2-to-1 multiplexer fed by two arbitrary 5-input functions sharing four inputs.
                     [source](Device Interfaces and Integration Basics for Cyclone V Devices).
                   end*/
                   else
diff --git a/techlibs/intel/cyclonev/cells_sim.v b/techlibs/intel/cyclonev/cells_sim.v
index 5ecdabcfc..9b2a10e72 100644
--- a/techlibs/intel/cyclonev/cells_sim.v
+++ b/techlibs/intel/cyclonev/cells_sim.v
@@ -54,7 +54,7 @@ module cyclonev_lcell_comb
    // Internal variables
    // Sub mask for fragmented LUTs
    wire [15:0] mask_a, mask_b, mask_c, mask_d;
-   // Independant output for fragmented LUTs
+   // Independent output for fragmented LUTs
    wire        output_0, output_1, output_2, output_3;
    // Extended mode uses mux to define the output
    wire        mux_0, mux_1;
@@ -85,7 +85,7 @@ module cyclonev_lcell_comb
       begin
          upper_lut_value = lut4(mask[31:16], dataa, datab, datac, datad);
          lower_lut_value = lut4(mask[15:0], dataa, datab, datac, datad);
-         lut5            = (datae) ? upper_mask_value : lower_mask_value;
+         lut5            = (datae) ? upper_lut_value : lower_lut_value;
       end
    endfunction // lut5
 
@@ -95,15 +95,16 @@ module cyclonev_lcell_comb
       input        dataa, datab, datac, datad, datae, dataf;
       reg          upper_lut_value;
       reg          lower_lut_value;
+      reg          out_0, out_1, out_2, out_3;
       begin
          upper_lut_value = lut5(mask[63:32], dataa, datab, datac, datad, datae);
          lower_lut_value = lut5(mask[31:0], dataa, datab, datac, datad, datae);
-         lut6            = (dataf) ?  upper_mask_value : lower_mask_value;
+         lut6            = (dataf) ?  upper_lut_value : lower_lut_value;
       end
    endfunction // lut6
 
    assign {mask_a, mask_b, mask_c, mask_d} = {lut_mask[15:0], lut_mask[31:16], lut_mask[47:32], lut_mask[63:48]};
-
+`ifdef ADVANCED_ALM
    always @(*) begin
       if(extended_lut == "on")
         shared_lut_alm = datag;
@@ -115,6 +116,11 @@ module cyclonev_lcell_comb
       out_2 = lut4(mask_c, dataa, datab, datac, datad);
       out_3 = lut4(mask_d, dataa, datab, shared_lut_alm, datad);
    end
+`else
+   `ifdef DEBUG
+       initial $display("Advanced ALM lut combine is not implemented yet");
+   `endif
+`endif
 endmodule // cyclonev_lcell_comb