brcm47xx: remove 2.6.25 support

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@15448 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 0 insertions, 72 deletions

diff --git a/target/linux/brcm47xx/patches-2.6.25/250-ohci-ssb-usb2.patch b/target/linux/brcm47xx/patches-2.6.25/250-ohci-ssb-usb2.patch
deleted file mode 100644
index 856651b3de..0000000000
--- a/target/linux/brcm47xx/patches-2.6.25/250-ohci-ssb-usb2.patch
+++ /dev/null
@@ -1,72 +0,0 @@
---- a/drivers/usb/host/ohci-ssb.c
-+++ b/drivers/usb/host/ohci-ssb.c
-@@ -142,10 +142,59 @@ static int ssb_ohci_attach(struct ssb_de
- 	int err = -ENOMEM;
- 	u32 tmp, flags = 0;
- 
--	if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV)
-+	/*
-+	 * THE FOLLOWING COMMENTS PRESERVED FROM GPL SOURCE RELEASE
-+	 *
-+	 * The USB core requires a special bit to be set during core
-+	 * reset to enable host (OHCI) mode. Resetting the SB core in
-+	 * pcibios_enable_device() is a hack for compatibility with
-+	 * vanilla usb-ohci so that it does not have to know about
-+	 * SB. A driver that wants to use the USB core in device mode
-+	 * should know about SB and should reset the bit back to 0
-+	 * after calling pcibios_enable_device().
-+	 */
-+
-+	if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) {
- 		flags |= SSB_OHCI_TMSLOW_HOSTMODE;
-+		ssb_device_enable(dev, flags);
-+	}
-+
-+	/*
-+	 * USB 2.0 special considerations:
-+	 *
-+	 * 1. Since the core supports both OHCI and EHCI functions, it must
-+	 *    only be reset once.
-+	 * 
-+	 * 2. In addition to the standard SB reset sequence, the Host Control
-+	 *    Register must be programmed to bring the USB core and various
-+	 *    phy components out of reset. 
-+	 */
-+
-+	else if (dev->id.coreid == SSB_DEV_USB20_HOST) {
-+#warning FIX ME need test for core being up & exit
-+		ssb_device_enable(dev, 0);
-+		ssb_write32(dev, 0x200, 0x7ff);
-+		udelay(1);
-+		if (dev->id.revision == 1) { // bug in rev 1
-+
-+			/* Change Flush control reg */
-+			tmp = ssb_read32(dev, 0x400);
-+			tmp &= ~8;
-+			ssb_write32(dev, 0x400, tmp);
-+			tmp = ssb_read32(dev, 0x400);
-+			printk("USB20H fcr: 0x%0x\n", tmp);
-+
-+			/* Change Shim control reg */
-+			tmp = ssb_read32(dev, 0x304);
-+			tmp &= ~0x100;
-+			ssb_write32(dev, 0x304, tmp);
-+			tmp = ssb_read32(dev, 0x304);
-+			printk("USB20H shim: 0x%0x\n", tmp);
-+		}
-+	}
-+	else
-+		ssb_device_enable(dev, 0);
- 
--	ssb_device_enable(dev, flags);
- 
- 	hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev,
- 			dev->dev->bus_id);
-@@ -236,6 +285,7 @@ static int ssb_ohci_resume(struct ssb_de
- static const struct ssb_device_id ssb_ohci_table[] = {
- 	SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOSTDEV, SSB_ANY_REV),
- 	SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOST, SSB_ANY_REV),
-+	SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB20_HOST, SSB_ANY_REV),
- 	SSB_DEVTABLE_END
- };
- MODULE_DEVICE_TABLE(ssb, ssb_ohci_table);