kirkwood: add Pogoplug E02 kernel support for 3.14

This also fixes a typo in the UBIFS_OPTS

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40827 3c298f89-4303-0410-b956-a3cf2f4a3e73

2 files changed, 128 insertions, 1 deletions

diff --git a/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch b/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch
new file mode 100644
index 0000000000..44b4c52556
--- /dev/null
+++ b/target/linux/kirkwood/patches-3.14/150-pogoplug_e02.patch
@@ -0,0 +1,127 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -112,6 +112,7 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-
+ 	kirkwood-nsa310a.dtb \
+ 	kirkwood-openblocks_a6.dtb \
+ 	kirkwood-openblocks_a7.dtb \
++	kirkwood-pogo_e02.dtb \
+ 	kirkwood-sheevaplug.dtb \
+ 	kirkwood-sheevaplug-esata.dtb \
+ 	kirkwood-topkick.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-pogo_e02.dts
+@@ -0,0 +1,114 @@
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6281.dtsi"
++
++/ {
++	model = "Cloud Engines Pogoplug E02";
++	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++	memory {
++		device_type = "memory";
++		reg = <0x00000000 0x10000000>;
++	};
++
++	chosen {
++		bootargs = "console=ttyS0,115200n8 earlyprintk";
++	};
++
++	ocp@f1000000 {
++		pinctrl: pinctrl@10000 {
++			pmx_usb_power_enable: pmx-usb-power-enable {
++				marvell,pins = "mpp29";
++				marvell,function = "gpio";
++			};
++			pmx_led_green: pmx-led_green {
++				marvell,pins = "mpp48";
++				marvell,function = "gpio";
++			};
++			pmx_led_orange: pmx-led_orange {
++				marvell,pins = "mpp49";
++				marvell,function = "gpio";
++			};
++		};
++		serial@12000 {
++			status = "ok";
++		};
++	};
++	gpio-leds {
++		compatible = "gpio-leds";
++		pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
++			      &pmx_led_green >;
++		pinctrl-names = "default";
++
++		health {
++			label = "status:green:health";
++			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
++			default-state = "keep";
++		};
++		fault {
++			label = "status:orange:fault";
++			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
++		};
++	};
++	regulators {
++		compatible = "simple-bus";
++		#address-cells = <1>;
++		#size-cells = <0>;
++		pinctrl-0 = <&pmx_usb_power_enable>;
++		pinctrl-names = "default";
++
++		usb_power: regulator@1 {
++			compatible = "regulator-fixed";
++			reg = <1>;
++			regulator-name = "USB Power";
++			regulator-min-microvolt = <5000000>;
++			regulator-max-microvolt = <5000000>;
++			enable-active-high;
++			regulator-always-on;
++			regulator-boot-on;
++			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
++		};
++	};
++};
++
++&nand {
++	chip-delay = <40>;
++	status = "okay";
++
++	partition@0 {
++		label = "u-boot";
++		reg = <0x0000000 0x100000>;
++		read-only;
++	};
++
++	partition@100000 {
++		label = "uImage";
++		reg = <0x0100000 0x400000>;
++	};
++
++	partition@500000 {
++		label = "pogoplug";
++		reg = <0x0500000 0x2000000>;
++	};
++
++	partition@2500000 {
++		label = "root";
++		reg = <0x02500000 0x5b00000>;
++	};
++};
++
++&mdio {
++	status = "okay";
++
++	ethphy0: ethernet-phy@0 {
++		reg = <0>;
++	};
++};
++
++&eth0 {
++	status = "okay";
++	ethernet0-port@0 {
++		phy-handle = <&ethphy0>;
++	};
++};
diff --git a/target/linux/kirkwood/profiles/120-pogoplug.mk b/target/linux/kirkwood/profiles/120-pogoplug.mk
index 47672f1114..d712dcb618 100644
--- a/target/linux/kirkwood/profiles/120-pogoplug.mk
+++ b/target/linux/kirkwood/profiles/120-pogoplug.mk
@@ -15,7 +15,7 @@ define Profile/POGOE02/Description
  Package set compatible with Cloud Engines Pogoplug E02 board.
 endef
 
-POGOE02_UBIFS_OPTS:="-m 2048 -e 128KiB -c 4096"
+POGOE02_UBIFS_OPTS:="-m 2048 -e 126KiB -c 4096"
 POGOE02_UBI_OPTS:="-m 2048 -p 128KiB -s 512"
 
 $(eval $(call Profile,POGOE02))