aboutsummaryrefslogtreecommitdiffstats
path: root/package/mac80211/src/include/net/mac80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'package/mac80211/src/include/net/mac80211.h')
-rw-r--r--package/mac80211/src/include/net/mac80211.h548
1 files changed, 328 insertions, 220 deletions
diff --git a/package/mac80211/src/include/net/mac80211.h b/package/mac80211/src/include/net/mac80211.h
index 2b1bffbf5e..460da54a00 100644
--- a/package/mac80211/src/include/net/mac80211.h
+++ b/package/mac80211/src/include/net/mac80211.h
@@ -69,95 +69,20 @@
* not do so then mac80211 may add this under certain circumstances.
*/
-#define IEEE80211_CHAN_W_SCAN 0x00000001
-#define IEEE80211_CHAN_W_ACTIVE_SCAN 0x00000002
-#define IEEE80211_CHAN_W_IBSS 0x00000004
-
-/* Channel information structure. Low-level driver is expected to fill in chan,
- * freq, and val fields. Other fields will be filled in by 80211.o based on
- * hostapd information and low-level driver does not need to use them. The
- * limits for each channel will be provided in 'struct ieee80211_conf' when
- * configuring the low-level driver with hw->config callback. If a device has
- * a default regulatory domain, IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED
- * can be set to let the driver configure all fields */
-struct ieee80211_channel {
- short chan; /* channel number (IEEE 802.11) */
- short freq; /* frequency in MHz */
- int val; /* hw specific value for the channel */
- int flag; /* flag for hostapd use (IEEE80211_CHAN_*) */
- unsigned char power_level;
- unsigned char antenna_max;
-};
-
-#define IEEE80211_RATE_ERP 0x00000001
-#define IEEE80211_RATE_BASIC 0x00000002
-#define IEEE80211_RATE_PREAMBLE2 0x00000004
-#define IEEE80211_RATE_SUPPORTED 0x00000010
-#define IEEE80211_RATE_OFDM 0x00000020
-#define IEEE80211_RATE_CCK 0x00000040
-#define IEEE80211_RATE_MANDATORY 0x00000100
-
-#define IEEE80211_RATE_CCK_2 (IEEE80211_RATE_CCK | IEEE80211_RATE_PREAMBLE2)
-#define IEEE80211_RATE_MODULATION(f) \
- (f & (IEEE80211_RATE_CCK | IEEE80211_RATE_OFDM))
-
-/* Low-level driver should set PREAMBLE2, OFDM and CCK flags.
- * BASIC, SUPPORTED, ERP, and MANDATORY flags are set in 80211.o based on the
- * configuration. */
-struct ieee80211_rate {
- int rate; /* rate in 100 kbps */
- int val; /* hw specific value for the rate */
- int flags; /* IEEE80211_RATE_ flags */
- int val2; /* hw specific value for the rate when using short preamble
- * (only when IEEE80211_RATE_PREAMBLE2 flag is set, i.e., for
- * 2, 5.5, and 11 Mbps) */
- signed char min_rssi_ack;
- unsigned char min_rssi_ack_delta;
-
- /* following fields are set by 80211.o and need not be filled by the
- * low-level driver */
- int rate_inv; /* inverse of the rate (LCM(all rates) / rate) for
- * optimizing channel utilization estimates */
-};
-
/**
- * enum ieee80211_phymode - PHY modes
+ * struct ieee80211_ht_bss_info - describing BSS's HT characteristics
*
- * @MODE_IEEE80211A: 5GHz as defined by 802.11a/802.11h
- * @MODE_IEEE80211B: 2.4 GHz as defined by 802.11b
- * @MODE_IEEE80211G: 2.4 GHz as defined by 802.11g (with OFDM),
- * backwards compatible with 11b mode
- * @NUM_IEEE80211_MODES: internal
- */
-enum ieee80211_phymode {
- MODE_IEEE80211A,
- MODE_IEEE80211B,
- MODE_IEEE80211G,
-
- /* keep last */
- NUM_IEEE80211_MODES
-};
-
-/**
- * struct ieee80211_hw_mode - PHY mode definition
- *
- * This structure describes the capabilities supported by the device
- * in a single PHY mode.
+ * This structure describes most essential parameters needed
+ * to describe 802.11n HT characteristics in a BSS
*
- * @mode: the PHY mode for this definition
- * @num_channels: number of supported channels
- * @channels: pointer to array of supported channels
- * @num_rates: number of supported bitrates
- * @rates: pointer to array of supported bitrates
- * @list: internal
+ * @primary_channel: channel number of primery channel
+ * @bss_cap: 802.11n's general BSS capabilities (e.g. channel width)
+ * @bss_op_mode: 802.11n's BSS operation modes (e.g. HT protection)
*/
-struct ieee80211_hw_mode {
- struct list_head list;
- struct ieee80211_channel *channels;
- struct ieee80211_rate *rates;
- enum ieee80211_phymode mode;
- int num_channels;
- int num_rates;
+struct ieee80211_ht_bss_info {
+ u8 primary_channel;
+ u8 bss_cap; /* use IEEE80211_HT_IE_CHA_ */
+ u8 bss_op_mode; /* use IEEE80211_HT_IE_ */
};
/**
@@ -208,6 +133,7 @@ struct ieee80211_tx_queue_stats_data {
* @IEEE80211_TX_QUEUE_AFTER_BEACON: transmit queue for frames to be
* sent after a beacon
* @IEEE80211_TX_QUEUE_BEACON: transmit queue for beacon frames
+ * @NUM_TX_DATA_QUEUES_AMPDU: adding more queues for A-MPDU
*/
enum ieee80211_tx_queue {
IEEE80211_TX_QUEUE_DATA0,
@@ -223,11 +149,12 @@ enum ieee80211_tx_queue {
* this struct need to have fixed values. As soon as it is removed, we can
* fix these entries. */
IEEE80211_TX_QUEUE_AFTER_BEACON = 6,
- IEEE80211_TX_QUEUE_BEACON = 7
+ IEEE80211_TX_QUEUE_BEACON = 7,
+ NUM_TX_DATA_QUEUES_AMPDU = 16
};
struct ieee80211_tx_queue_stats {
- struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES];
+ struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES_AMPDU];
};
struct ieee80211_low_level_stats {
@@ -237,16 +164,56 @@ struct ieee80211_low_level_stats {
unsigned int dot11RTSSuccessCount;
};
+/**
+ * enum ieee80211_bss_change - BSS change notification flags
+ *
+ * These flags are used with the bss_info_changed() callback
+ * to indicate which BSS parameter changed.
+ *
+ * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
+ * also implies a change in the AID.
+ * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
+ * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
+ */
+enum ieee80211_bss_change {
+ BSS_CHANGED_ASSOC = 1<<0,
+ BSS_CHANGED_ERP_CTS_PROT = 1<<1,
+ BSS_CHANGED_ERP_PREAMBLE = 1<<2,
+};
+
+/**
+ * struct ieee80211_bss_conf - holds the BSS's changing parameters
+ *
+ * This structure keeps information about a BSS (and an association
+ * to that BSS) that can change during the lifetime of the BSS.
+ *
+ * @assoc: association status
+ * @aid: association ID number, valid only when @assoc is true
+ * @use_cts_prot: use CTS protection
+ * @use_short_preamble: use 802.11b short preamble
+ */
+struct ieee80211_bss_conf {
+ /* association related data */
+ bool assoc;
+ u16 aid;
+ /* erp related data */
+ bool use_cts_prot;
+ bool use_short_preamble;
+};
+
/* Transmit control fields. This data structure is passed to low-level driver
* with each TX frame. The low-level driver is responsible for configuring
* the hardware to use given values (depending on what is supported). */
struct ieee80211_tx_control {
- int tx_rate; /* Transmit rate, given as the hw specific value for the
- * rate (from struct ieee80211_rate) */
- int rts_cts_rate; /* Transmit rate for RTS/CTS frame, given as the hw
- * specific value for the rate (from
- * struct ieee80211_rate) */
+ struct ieee80211_vif *vif;
+ struct ieee80211_rate *tx_rate;
+
+ /* Transmit rate for RTS/CTS frame */
+ struct ieee80211_rate *rts_cts_rate;
+
+ /* retry rate for the last retries */
+ struct ieee80211_rate *alt_retry_rate;
#define IEEE80211_TXCTL_REQ_TX_STATUS (1<<0)/* request TX status callback for
* this frame */
@@ -265,10 +232,16 @@ struct ieee80211_tx_control {
#define IEEE80211_TXCTL_REQUEUE (1<<7)
#define IEEE80211_TXCTL_FIRST_FRAGMENT (1<<8) /* this is a first fragment of
* the frame */
+#define IEEE80211_TXCTL_SHORT_PREAMBLE (1<<9)
#define IEEE80211_TXCTL_LONG_RETRY_LIMIT (1<<10) /* this frame should be send
* using the through
* set_retry_limit configured
* long retry value */
+#define IEEE80211_TXCTL_EAPOL_FRAME (1<<11) /* internal to mac80211 */
+#define IEEE80211_TXCTL_SEND_AFTER_DTIM (1<<12) /* send this frame after DTIM
+ * beacon */
+#define IEEE80211_TXCTL_AMPDU (1<<13) /* this frame should be sent
+ * as part of an A-MPDU */
u32 flags; /* tx control flags defined
* above */
u8 key_idx; /* keyidx from hw->set_key(), undefined if
@@ -276,22 +249,12 @@ struct ieee80211_tx_control {
u8 retry_limit; /* 1 = only first attempt, 2 = one retry, ..
* This could be used when set_retry_limit
* is not implemented by the driver */
- u8 power_level; /* per-packet transmit power level, in dBm */
u8 antenna_sel_tx; /* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */
u8 icv_len; /* length of the ICV/MIC field in octets */
u8 iv_len; /* length of the IV field in octets */
u8 queue; /* hardware queue to use for this frame;
* 0 = highest, hw->queues-1 = lowest */
- struct ieee80211_rate *rate; /* internal 80211.o rate */
- struct ieee80211_rate *rts_rate; /* internal 80211.o rate
- * for RTS/CTS */
- int alt_retry_rate; /* retry rate for the last retries, given as the
- * hw specific value for the rate (from
- * struct ieee80211_rate). To be used to limit
- * packet dropping when probing higher rates, if hw
- * supports multiple retry rates. -1 = not used */
int type; /* internal */
- int ifindex; /* internal */
};
@@ -312,6 +275,8 @@ struct ieee80211_tx_control {
* the frame.
* @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
* the frame.
+ * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field)
+ * is valid.
*/
enum mac80211_rx_flags {
RX_FLAG_MMIC_ERROR = 1<<0,
@@ -321,6 +286,7 @@ enum mac80211_rx_flags {
RX_FLAG_IV_STRIPPED = 1<<4,
RX_FLAG_FAILED_FCS_CRC = 1<<5,
RX_FLAG_FAILED_PLCP_CRC = 1<<6,
+ RX_FLAG_TSFT = 1<<7,
};
/**
@@ -330,26 +296,24 @@ enum mac80211_rx_flags {
* supported by hardware) to the 802.11 code with each received
* frame.
* @mactime: MAC timestamp as defined by 802.11
+ * @band: the active band when this frame was received
* @freq: frequency the radio was tuned to when receiving this frame, in MHz
- * @channel: channel the radio was tuned to
- * @phymode: active PHY mode
* @ssi: signal strength when receiving this frame
* @signal: used as 'qual' in statistics reporting
* @noise: PHY noise when receiving this frame
* @antenna: antenna used
- * @rate: data rate
+ * @rate_idx: index of data rate into band's supported rates
* @flag: %RX_FLAG_*
*/
struct ieee80211_rx_status {
u64 mactime;
+ enum ieee80211_band band;
int freq;
- int channel;
- enum ieee80211_phymode phymode;
int ssi;
int signal;
int noise;
int antenna;
- int rate;
+ int rate_idx;
int flag;
};
@@ -360,12 +324,14 @@ struct ieee80211_rx_status {
*
* @IEEE80211_TX_STATUS_TX_FILTERED: The frame was not transmitted
* because the destination STA was in powersave mode.
- *
* @IEEE80211_TX_STATUS_ACK: Frame was acknowledged
+ * @IEEE80211_TX_STATUS_AMPDU: The frame was aggregated, so status
+ * is for the whole aggregation.
*/
enum ieee80211_tx_status_flags {
IEEE80211_TX_STATUS_TX_FILTERED = 1<<0,
IEEE80211_TX_STATUS_ACK = 1<<1,
+ IEEE80211_TX_STATUS_AMPDU = 1<<2,
};
/**
@@ -376,24 +342,25 @@ enum ieee80211_tx_status_flags {
*
* @control: a copy of the &struct ieee80211_tx_control passed to the driver
* in the tx() callback.
- *
* @flags: transmit status flags, defined above
- *
- * @ack_signal: signal strength of the ACK frame
- *
+ * @retry_count: number of retries
* @excessive_retries: set to 1 if the frame was retried many times
* but not acknowledged
- *
- * @retry_count: number of retries
- *
+ * @ampdu_ack_len: number of aggregated frames.
+ * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
+ * @ampdu_ack_map: block ack bit map for the aggregation.
+ * relevant only if IEEE80211_TX_STATUS_AMPDU was set.
+ * @ack_signal: signal strength of the ACK frame
* @queue_length: ?? REMOVE
* @queue_number: ?? REMOVE
*/
struct ieee80211_tx_status {
struct ieee80211_tx_control control;
u8 flags;
- bool excessive_retries;
u8 retry_count;
+ bool excessive_retries;
+ u8 ampdu_ack_len;
+ u64 ampdu_ack_map;
int ack_signal;
int queue_length;
int queue_number;
@@ -406,11 +373,12 @@ struct ieee80211_tx_status {
*
* @IEEE80211_CONF_SHORT_SLOT_TIME: use 802.11g short slot time
* @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
- *
+ * @IEEE80211_CONF_SUPPORT_HT_MODE: use 802.11n HT capabilities (if supported)
*/
enum ieee80211_conf_flags {
- IEEE80211_CONF_SHORT_SLOT_TIME = 1<<0,
- IEEE80211_CONF_RADIOTAP = 1<<1,
+ IEEE80211_CONF_SHORT_SLOT_TIME = (1<<0),
+ IEEE80211_CONF_RADIOTAP = (1<<1),
+ IEEE80211_CONF_SUPPORT_HT_MODE = (1<<2),
};
/**
@@ -420,38 +388,32 @@ enum ieee80211_conf_flags {
*
* @radio_enabled: when zero, driver is required to switch off the radio.
* TODO make a flag
- * @channel: IEEE 802.11 channel number
- * @freq: frequency in MHz
- * @channel_val: hardware specific channel value for the channel
- * @phymode: PHY mode to activate (REMOVE)
- * @chan: channel to switch to, pointer to the channel information
- * @mode: pointer to mode definition
- * @regulatory_domain: ??
* @beacon_int: beacon interval (TODO make interface config)
* @flags: configuration flags defined above
- * @power_level: transmit power limit for current regulatory domain in dBm
- * @antenna_max: maximum antenna gain
+ * @power_level: requested transmit power (in dBm)
+ * @max_antenna_gain: maximum antenna gain (in dBi)
* @antenna_sel_tx: transmit antenna selection, 0: default/diversity,
* 1/2: antenna 0/1
* @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx
+ * @ht_conf: describes current self configuration of 802.11n HT capabilies
+ * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters
+ * @channel: the channel to tune to
*/
struct ieee80211_conf {
- int channel; /* IEEE 802.11 channel number */
- int freq; /* MHz */
- int channel_val; /* hw specific value for the channel */
-
- enum ieee80211_phymode phymode;
- struct ieee80211_channel *chan;
- struct ieee80211_hw_mode *mode;
unsigned int regulatory_domain;
int radio_enabled;
int beacon_int;
u32 flags;
- u8 power_level;
- u8 antenna_max;
+ int power_level;
+ int max_antenna_gain;
u8 antenna_sel_tx;
u8 antenna_sel_rx;
+
+ struct ieee80211_channel *channel;
+
+ struct ieee80211_ht_info ht_conf;
+ struct ieee80211_ht_bss_info ht_bss_conf;
};
/**
@@ -480,13 +442,27 @@ enum ieee80211_if_types {
};
/**
+ * struct ieee80211_vif - per-interface data
+ *
+ * Data in this structure is continually present for driver
+ * use during the life of a virtual interface.
+ *
+ * @type: type of this virtual interface
+ * @drv_priv: data area for driver use, will always be aligned to
+ * sizeof(void *).
+ */
+struct ieee80211_vif {
+ enum ieee80211_if_types type;
+ /* must be last */
+ u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
+};
+
+/**
* struct ieee80211_if_init_conf - initial configuration of an interface
*
- * @if_id: internal interface ID. This number has no particular meaning to
- * drivers and the only allowed usage is to pass it to
- * ieee80211_beacon_get() and ieee80211_get_buffered_bc() functions.
- * This field is not valid for monitor interfaces
- * (interfaces of %IEEE80211_IF_TYPE_MNTR type).
+ * @vif: pointer to a driver-use per-interface structure. The pointer
+ * itself is also used for various functions including
+ * ieee80211_beacon_get() and ieee80211_get_buffered_bc().
* @type: one of &enum ieee80211_if_types constants. Determines the type of
* added/removed interface.
* @mac_addr: pointer to MAC address of the interface. This pointer is valid
@@ -503,8 +479,8 @@ enum ieee80211_if_types {
* in pure monitor mode.
*/
struct ieee80211_if_init_conf {
- int if_id;
enum ieee80211_if_types type;
+ struct ieee80211_vif *vif;
void *mac_addr;
};
@@ -597,9 +573,6 @@ struct ieee80211_key_conf {
u8 key[0];
};
-#define IEEE80211_SEQ_COUNTER_RX 0
-#define IEEE80211_SEQ_COUNTER_TX 1
-
/**
* enum set_key_cmd - key command
*
@@ -659,15 +632,19 @@ enum sta_notify_cmd {
* %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because
* otherwise the stack will not know when the DTIM beacon was sent.
*
- * @IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED:
- * Channels are already configured to the default regulatory domain
- * specified in the device's EEPROM
+ * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
+ * Hardware is not capable of short slot operation on the 2.4 GHz band.
+ *
+ * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
+ * Hardware is not capable of receiving frames with short preamble on
+ * the 2.4 GHz band.
*/
enum ieee80211_hw_flags {
IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0,
IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
- IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED = 1<<3,
+ IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
+ IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
};
/**
@@ -679,7 +656,8 @@ enum ieee80211_hw_flags {
* @wiphy: This points to the &struct wiphy allocated for this
* 802.11 PHY. You must fill in the @perm_addr and @dev
* members of this structure using SET_IEEE80211_DEV()
- * and SET_IEEE80211_PERM_ADDR().
+ * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
+ * bands (with channels, bitrates) are registered here.
*
* @conf: &struct ieee80211_conf, device configuration, don't use.
*
@@ -706,15 +684,24 @@ enum ieee80211_hw_flags {
*
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four.
+ *
+ * @rate_control_algorithm: rate control algorithm for this hardware.
+ * If unset (NULL), the default algorithm will be used. Must be
+ * set before calling ieee80211_register_hw().
+ *
+ * @vif_data_size: size (in bytes) of the drv_priv data area
+ * within &struct ieee80211_vif.
*/
struct ieee80211_hw {
struct ieee80211_conf conf;
struct wiphy *wiphy;
struct workqueue_struct *workqueue;
+ const char *rate_control_algorithm;
void *priv;
u32 flags;
unsigned int extra_tx_headroom;
int channel_change_time;
+ int vif_data_size;
u8 queues;
s8 max_rssi;
s8 max_signal;
@@ -854,19 +841,22 @@ enum ieee80211_filter_flags {
};
/**
- * enum ieee80211_erp_change_flags - erp change flags
- *
- * These flags are used with the erp_ie_changed() callback in
- * &struct ieee80211_ops to indicate which parameter(s) changed.
- * @IEEE80211_ERP_CHANGE_PROTECTION: protection changed
- * @IEEE80211_ERP_CHANGE_PREAMBLE: barker preamble mode changed
+ * enum ieee80211_ampdu_mlme_action - A-MPDU actions
+ *
+ * These flags are used with the ampdu_action() callback in
+ * &struct ieee80211_ops to indicate which action is needed.
+ * @IEEE80211_AMPDU_RX_START: start Rx aggregation
+ * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation
+ * @IEEE80211_AMPDU_TX_START: start Tx aggregation
+ * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation
*/
-enum ieee80211_erp_change_flags {
- IEEE80211_ERP_CHANGE_PROTECTION = 1<<0,
- IEEE80211_ERP_CHANGE_PREAMBLE = 1<<1,
+enum ieee80211_ampdu_mlme_action {
+ IEEE80211_AMPDU_RX_START,
+ IEEE80211_AMPDU_RX_STOP,
+ IEEE80211_AMPDU_TX_START,
+ IEEE80211_AMPDU_TX_STOP,
};
-
/**
* struct ieee80211_ops - callbacks from mac80211 to the driver
*
@@ -922,6 +912,14 @@ enum ieee80211_erp_change_flags {
* @config_interface: Handler for configuration requests related to interfaces
* (e.g. BSSID changes.)
*
+ * @bss_info_changed: Handler for configuration requests related to BSS
+ * parameters that may vary during BSS's lifespan, and may affect low
+ * level driver (e.g. assoc/disassoc status, erp parameters).
+ * This function should not be used if no BSS has been set, unless
+ * for association indication. The @changed parameter indicates which
+ * of the bss parameters has changed when a call is made. This callback
+ * has to be atomic.
+ *
* @configure_filter: Configure the device's RX filter.
* See the section "Frame filtering" for more information.
* This callback must be implemented and atomic.
@@ -936,30 +934,16 @@ enum ieee80211_erp_change_flags {
* and remove_interface calls, i.e. while the interface with the
* given local_address is enabled.
*
- * @set_ieee8021x: Enable/disable IEEE 802.1X. This item requests wlan card
- * to pass unencrypted EAPOL-Key frames even when encryption is
- * configured. If the wlan card does not require such a configuration,
- * this function pointer can be set to NULL.
- *
- * @set_port_auth: Set port authorization state (IEEE 802.1X PAE) to be
- * authorized (@authorized=1) or unauthorized (=0). This function can be
- * used if the wlan hardware or low-level driver implements PAE.
- * mac80211 will filter frames based on authorization state in any case,
- * so this function pointer can be NULL if low-level driver does not
- * require event notification about port state changes.
- *
* @hw_scan: Ask the hardware to service the scan request, no need to start
- * the scan state machine in stack.
+ * the scan state machine in stack. The scan must honour the channel
+ * configuration done by the regulatory agent in the wiphy's registered
+ * bands.
*
* @get_stats: return low-level statistics
*
- * @set_privacy_invoked: For devices that generate their own beacons and probe
- * response or association responses this updates the state of privacy_invoked
- * returns 0 for success or an error number.
- *
- * @get_sequence_counter: For devices that have internal sequence counters this
- * callback allows mac80211 to access the current value of a counter.
- * This callback seems not well-defined, tell us if you need it.
+ * @get_tkip_seq: If your device implements TKIP encryption in hardware this
+ * callback should be provided to read the TKIP transmit IVs (both IV32
+ * and IV16) for the given key from hardware.
*
* @set_rts_threshold: Configuration of RTS threshold (if device needs it)
*
@@ -972,8 +956,6 @@ enum ieee80211_erp_change_flags {
* @sta_notify: Notifies low level driver about addition or removal
* of assocaited station or AP.
*
- * @erp_ie_changed: Handle ERP IE change notifications. Must be atomic.
- *
* @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
* bursting) for a hardware TX queue. The @queue parameter uses the
* %IEEE80211_TX_QUEUE_* constants. Must be atomic.
@@ -1008,6 +990,15 @@ enum ieee80211_erp_change_flags {
* @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
* This is needed only for IBSS mode and the result of this function is
* used to determine whether to reply to Probe Requests.
+ *
+ * @conf_ht: Configures low level driver with 802.11n HT data. Must be atomic.
+ *
+ * @ampdu_action: Perform a certain A-MPDU action
+ * The RA/TID combination determines the destination and TID we want
+ * the ampdu action to be performed for. The action is defined through
+ * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
+ * is the first frame we expect to perform the action on. notice
+ * that TX/RX_STOP can pass NULL for this parameter.
*/
struct ieee80211_ops {
int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb,
@@ -1020,7 +1011,12 @@ struct ieee80211_ops {
struct ieee80211_if_init_conf *conf);
int (*config)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
int (*config_interface)(struct ieee80211_hw *hw,
- int if_id, struct ieee80211_if_conf *conf);
+ struct ieee80211_vif *vif,
+ struct ieee80211_if_conf *conf);
+ void (*bss_info_changed)(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ struct ieee80211_bss_conf *info,
+ u32 changed);
void (*configure_filter)(struct ieee80211_hw *hw,
unsigned int changed_flags,
unsigned int *total_flags,
@@ -1029,25 +1025,17 @@ struct ieee80211_ops {
int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
const u8 *local_address, const u8 *address,
struct ieee80211_key_conf *key);
- int (*set_ieee8021x)(struct ieee80211_hw *hw, int use_ieee8021x);
- int (*set_port_auth)(struct ieee80211_hw *hw, u8 *addr,
- int authorized);
int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len);
int (*get_stats)(struct ieee80211_hw *hw,
struct ieee80211_low_level_stats *stats);
- int (*set_privacy_invoked)(struct ieee80211_hw *hw,
- int privacy_invoked);
- int (*get_sequence_counter)(struct ieee80211_hw *hw,
- u8* addr, u8 keyidx, u8 txrx,
- u32* iv32, u16* iv16);
+ void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx,
+ u32 *iv32, u16 *iv16);
int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
int (*set_retry_limit)(struct ieee80211_hw *hw,
u32 short_retry, u32 long_retr);
- void (*sta_notify)(struct ieee80211_hw *hw, int if_id,
+ void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
enum sta_notify_cmd, const u8 *addr);
- void (*erp_ie_changed)(struct ieee80211_hw *hw, u8 changes,
- int cts_protection, int preamble);
int (*conf_tx)(struct ieee80211_hw *hw, int queue,
const struct ieee80211_tx_queue_params *params);
int (*get_tx_stats)(struct ieee80211_hw *hw,
@@ -1058,6 +1046,10 @@ struct ieee80211_ops {
struct sk_buff *skb,
struct ieee80211_tx_control *control);
int (*tx_last_beacon)(struct ieee80211_hw *hw);
+ int (*conf_ht)(struct ieee80211_hw *hw, struct ieee80211_conf *conf);
+ int (*ampdu_action)(struct ieee80211_hw *hw,
+ enum ieee80211_ampdu_mlme_action action,
+ const u8 *addr, u16 tid, u16 *ssn);
};
/**
@@ -1089,6 +1081,7 @@ int ieee80211_register_hw(struct ieee80211_hw *hw);
extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
+extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
#endif
/**
* ieee80211_get_tx_led_name - get name of TX LED
@@ -1128,6 +1121,16 @@ static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
#endif
}
+/**
+ * ieee80211_get_assoc_led_name - get name of association LED
+ *
+ * mac80211 creates a association LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
{
#ifdef CONFIG_MAC80211_LEDS
@@ -1137,10 +1140,24 @@ static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
#endif
}
-
-/* Register a new hardware PHYMODE capability to the stack. */
-int ieee80211_register_hwmode(struct ieee80211_hw *hw,
- struct ieee80211_hw_mode *mode);
+/**
+ * ieee80211_get_radio_led_name - get name of radio LED
+ *
+ * mac80211 creates a radio change LED trigger for each wireless hardware
+ * that can be used to drive LEDs if your driver registers a LED device.
+ * This function returns the name (or %NULL if not configured for LEDs)
+ * of the trigger so you can automatically link the LED device.
+ *
+ * @hw: the hardware to get the LED trigger name for
+ */
+static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
+{
+#ifdef CONFIG_MAC80211_LEDS
+ return __ieee80211_get_radio_led_name(hw);
+#else
+ return NULL;
+#endif
+}
/**
* ieee80211_unregister_hw - Unregister a hardware device
@@ -1226,7 +1243,7 @@ void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
/**
* ieee80211_beacon_get - beacon generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @control: will be filled with information needed to send this beacon.
*
* If the beacon frames are generated by the host system (i.e., not in
@@ -1237,13 +1254,13 @@ void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
* is responsible of freeing it.
*/
struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
- int if_id,
+ struct ieee80211_vif *vif,
struct ieee80211_tx_control *control);
/**
* ieee80211_rts_get - RTS frame generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame: pointer to the frame that is going to be protected by the RTS.
* @frame_len: the frame length (in octets).
* @frame_txctl: &struct ieee80211_tx_control of the frame.
@@ -1254,7 +1271,7 @@ struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
* the next RTS frame from the 802.11 code. The low-level is responsible
* for calling this function before and RTS frame is needed.
*/
-void ieee80211_rts_get(struct ieee80211_hw *hw, int if_id,
+void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
const struct ieee80211_tx_control *frame_txctl,
struct ieee80211_rts *rts);
@@ -1262,7 +1279,7 @@ void ieee80211_rts_get(struct ieee80211_hw *hw, int if_id,
/**
* ieee80211_rts_duration - Get the duration field for an RTS frame
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame that is going to be protected by the RTS.
* @frame_txctl: &struct ieee80211_tx_control of the frame.
*
@@ -1270,14 +1287,14 @@ void ieee80211_rts_get(struct ieee80211_hw *hw, int if_id,
* the duration field, the low-level driver uses this function to receive
* the duration field value in little-endian byteorder.
*/
-__le16 ieee80211_rts_duration(struct ieee80211_hw *hw, int if_id,
- size_t frame_len,
+__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif, size_t frame_len,
const struct ieee80211_tx_control *frame_txctl);
/**
* ieee80211_ctstoself_get - CTS-to-self frame generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame: pointer to the frame that is going to be protected by the CTS-to-self.
* @frame_len: the frame length (in octets).
* @frame_txctl: &struct ieee80211_tx_control of the frame.
@@ -1288,7 +1305,8 @@ __le16 ieee80211_rts_duration(struct ieee80211_hw *hw, int if_id,
* the next CTS-to-self frame from the 802.11 code. The low-level is responsible
* for calling this function before and CTS-to-self frame is needed.
*/
-void ieee80211_ctstoself_get(struct ieee80211_hw *hw, int if_id,
+void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
const void *frame, size_t frame_len,
const struct ieee80211_tx_control *frame_txctl,
struct ieee80211_cts *cts);
@@ -1296,7 +1314,7 @@ void ieee80211_ctstoself_get(struct ieee80211_hw *hw, int if_id,
/**
* ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
* @frame_txctl: &struct ieee80211_tx_control of the frame.
*
@@ -1304,28 +1322,30 @@ void ieee80211_ctstoself_get(struct ieee80211_hw *hw, int if_id,
* the duration field, the low-level driver uses this function to receive
* the duration field value in little-endian byteorder.
*/
-__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, int if_id,
+__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
size_t frame_len,
const struct ieee80211_tx_control *frame_txctl);
/**
* ieee80211_generic_frame_duration - Calculate the duration field for a frame
* @hw: pointer obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @frame_len: the length of the frame.
- * @rate: the rate (in 100kbps) at which the frame is going to be transmitted.
+ * @rate: the rate at which the frame is going to be transmitted.
*
* Calculate the duration field of some generic frame, given its
* length and transmission rate (in 100kbps).
*/
-__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, int if_id,
+__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
size_t frame_len,
- int rate);
+ struct ieee80211_rate *rate);
/**
* ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
* @hw: pointer as obtained from ieee80211_alloc_hw().
- * @if_id: interface ID from &struct ieee80211_if_init_conf.
+ * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf.
* @control: will be filled with information needed to send returned frame.
*
* Function for accessing buffered broadcast and multicast frames. If
@@ -1344,7 +1364,7 @@ __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, int if_id,
* use common code for all beacons.
*/
struct sk_buff *
-ieee80211_get_buffered_bc(struct ieee80211_hw *hw, int if_id,
+ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
struct ieee80211_tx_control *control);
/**
@@ -1422,8 +1442,96 @@ void ieee80211_wake_queues(struct ieee80211_hw *hw);
*/
void ieee80211_scan_completed(struct ieee80211_hw *hw);
-#define MAC_FMT "%02x:%02x:%02x:%02x:%02x:%02x"
-#define MAC_ARG(x) ((u8*)(x))[0], ((u8*)(x))[1], ((u8*)(x))[2], \
- ((u8*)(x))[3], ((u8*)(x))[4], ((u8*)(x))[5]
+/**
+ * ieee80211_iterate_active_interfaces - iterate active interfaces
+ *
+ * This function iterates over the interfaces associated with a given
+ * hardware that are currently active and calls the callback for them.
+ *
+ * @hw: the hardware struct of which the interfaces should be iterated over
+ * @iterator: the iterator function to call, cannot sleep
+ * @data: first argument of the iterator function
+ */
+void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw,
+ void (*iterator)(void *data, u8 *mac,
+ struct ieee80211_vif *vif),
+ void *data);
+
+/**
+ * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient
+ * @tid: the TID to BA on.
+ * @return: success if addBA request was sent, failure otherwise
+ *
+ * Although mac80211/low level driver/user space application can estimate
+ * the need to start aggregation on a certain RA/TID, the session level
+ * will be managed by the mac80211.
+ */
+int ieee80211_start_tx_ba_session(struct ieee80211_hw *hw, u8 *ra, u16 tid);
+
+/**
+ * ieee80211_start_tx_ba_cb - low level driver ready to aggregate.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session.
+ */
+void ieee80211_start_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u16 tid);
+
+/**
+ * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session.
+ * This version of the function is irq safe.
+ */
+void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
+ u16 tid);
+
+/**
+ * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient
+ * @tid: the TID to stop BA.
+ * @initiator: if indicates initiator DELBA frame will be sent.
+ * @return: error if no sta with matching da found, success otherwise
+ *
+ * Although mac80211/low level driver/user space application can estimate
+ * the need to stop aggregation on a certain RA/TID, the session level
+ * will be managed by the mac80211.
+ */
+int ieee80211_stop_tx_ba_session(struct ieee80211_hw *hw,
+ u8 *ra, u16 tid,
+ enum ieee80211_back_parties initiator);
+
+/**
+ * ieee80211_stop_tx_ba_cb - low level driver ready to stop aggregate.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the desired TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session tear down.
+ */
+void ieee80211_stop_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u8 tid);
+
+/**
+ * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
+ * @hw: pointer as obtained from ieee80211_alloc_hw().
+ * @ra: receiver address of the BA session recipient.
+ * @tid: the desired TID to BA on.
+ *
+ * This function must be called by low level driver once it has
+ * finished with preparations for the BA session tear down.
+ * This version of the function is irq safe.
+ */
+void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
+ u16 tid);
#endif /* MAC80211_H */