diff options
Diffstat (limited to 'target/linux/brcm2708/patches-4.4/0033-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch')
-rw-r--r-- | target/linux/brcm2708/patches-4.4/0033-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch | 2022 |
1 files changed, 2022 insertions, 0 deletions
diff --git a/target/linux/brcm2708/patches-4.4/0033-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch b/target/linux/brcm2708/patches-4.4/0033-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch new file mode 100644 index 0000000000..d49e57b2c1 --- /dev/null +++ b/target/linux/brcm2708/patches-4.4/0033-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch @@ -0,0 +1,2022 @@ +From 8c767f6b8d65c2c59995ed51512faeaf56fbb2c3 Mon Sep 17 00:00:00 2001 +From: Phil Elwell <phil@raspberrypi.org> +Date: Wed, 25 Mar 2015 17:49:47 +0000 +Subject: [PATCH 033/381] Adding bcm2835-sdhost driver, and an overlay to + enable it + +BCM2835 has two SD card interfaces. This driver uses the other one. + +bcm2835-sdhost: Error handling fix, and code clarification + +bcm2835-sdhost: Adding overclocking option + +Allow a different clock speed to be substitued for a requested 50MHz. +This option is exposed using the "overclock_50" DT parameter. +Note that the sdhost interface is restricted to integer divisions of +core_freq, and the highest sensible option for a core_freq of 250MHz +is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too +high. + +Use at your own risk. + +bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz + +Also only warn once for each overclock setting. + +bcm2835-sdhost: Improve error handling and recovery + +1) Expose the hw_reset method to the MMC framework, removing many + internal calls by the driver. + +2) Reduce overclock setting on error. + +3) Increase timeout to cope with high capacity cards. + +4) Add properties and parameters to control pio_limit and debug. + +5) Reduce messages at probe time. + +bcm2835-sdhost: Further improve overclock back-off + +bcm2835-sdhost: Clear HBLC for PIO mode + +Also update pio_limit default in overlay README. + +bcm2835-sdhost: Add the ERASE capability + +See: https://github.com/raspberrypi/linux/issues/1076 + +bcm2835-sdhost: Ignore CRC7 for MMC CMD1 + +It seems that the sdhost interface returns CRC7 errors for CMD1, +which is the MMC-specific SEND_OP_COND. Returning these errors to +the MMC layer causes a downward spiral, but ignoring them seems +to be harmless. + +bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences + +The bcm2835-mmc driver (and -sdhost driver that copied from it) +contains code to handle SDIO interrupts in a threaded interrupt +handler rather than waking the MMC framework thread. The change +follows a patch from Russell King that adds the facility as the +preferred way of working. + +However, the new code path is only present in ARCH_BCM2835 +builds, which I have taken to be a way of testing the waters +rather than making the change across the board; I can't see +any technical reason why it wouldn't be enabled for MACH_BCM270X +builds. So this patch standardises on the ARCH_BCM2835 code, +removing the old code paths. + +bcm2835-sdhost: Don't log timeout errors unless debug=1 + +The MMC card-discovery process generates timeouts. This is +expected behaviour, so reporting it to the user serves no purpose. +Suppress the reporting of timeout errors unless the debug flag +is on. +--- + drivers/mmc/host/Kconfig | 10 + + drivers/mmc/host/Makefile | 1 + + drivers/mmc/host/bcm2835-sdhost.c | 1907 +++++++++++++++++++++++++++++++++++++ + 3 files changed, 1918 insertions(+) + create mode 100644 drivers/mmc/host/bcm2835-sdhost.c + +--- a/drivers/mmc/host/Kconfig ++++ b/drivers/mmc/host/Kconfig +@@ -33,6 +33,16 @@ config MMC_BCM2835_PIO_DMA_BARRIER + + If unsure, say 2 here. + ++config MMC_BCM2835_SDHOST ++ tristate "Support for the SDHost controller on BCM2708/9" ++ depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835 ++ help ++ This selects the SDHost controller on BCM2835/6. ++ ++ If you have a controller with this interface, say Y or M here. ++ ++ If unsure, say N. ++ + config MMC_ARMMMCI + tristate "ARM AMBA Multimedia Card Interface support" + depends on ARM_AMBA +--- a/drivers/mmc/host/Makefile ++++ b/drivers/mmc/host/Makefile +@@ -18,6 +18,7 @@ obj-$(CONFIG_MMC_SDHCI_S3C) += sdhci-s3c + obj-$(CONFIG_MMC_SDHCI_SIRF) += sdhci-sirf.o + obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci_f_sdh30.o + obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o ++obj-$(CONFIG_MMC_BCM2835_SDHOST) += bcm2835-sdhost.o + obj-$(CONFIG_MMC_BCM2835) += bcm2835-mmc.o + obj-$(CONFIG_MMC_WBSD) += wbsd.o + obj-$(CONFIG_MMC_AU1X) += au1xmmc.o +--- /dev/null ++++ b/drivers/mmc/host/bcm2835-sdhost.c +@@ -0,0 +1,1907 @@ ++/* ++ * BCM2835 SD host driver. ++ * ++ * Author: Phil Elwell <phil@raspberrypi.org> ++ * Copyright 2015 ++ * ++ * Based on ++ * mmc-bcm2835.c by Gellert Weisz ++ * which is, in turn, based on ++ * sdhci-bcm2708.c by Broadcom ++ * sdhci-bcm2835.c by Stephen Warren and Oleksandr Tymoshenko ++ * sdhci.c and sdhci-pci.c by Pierre Ossman ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms and conditions of the GNU General Public License, ++ * version 2, as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope it will be useful, but WITHOUT ++ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or ++ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for ++ * more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program. If not, see <http://www.gnu.org/licenses/>. ++ */ ++ ++#define SAFE_READ_THRESHOLD 4 ++#define SAFE_WRITE_THRESHOLD 4 ++#define ALLOW_DMA 1 ++#define ALLOW_CMD23 0 ++#define ALLOW_FAST 1 ++#define USE_BLOCK_IRQ 1 ++ ++#include <linux/delay.h> ++#include <linux/module.h> ++#include <linux/io.h> ++#include <linux/mmc/mmc.h> ++#include <linux/mmc/host.h> ++#include <linux/mmc/sd.h> ++#include <linux/scatterlist.h> ++#include <linux/of_address.h> ++#include <linux/of_irq.h> ++#include <linux/clk.h> ++#include <linux/platform_device.h> ++#include <linux/err.h> ++#include <linux/blkdev.h> ++#include <linux/dmaengine.h> ++#include <linux/dma-mapping.h> ++#include <linux/of_dma.h> ++#include <linux/time.h> ++ ++#define DRIVER_NAME "sdhost-bcm2835" ++ ++#define SDCMD 0x00 /* Command to SD card - 16 R/W */ ++#define SDARG 0x04 /* Argument to SD card - 32 R/W */ ++#define SDTOUT 0x08 /* Start value for timeout counter - 32 R/W */ ++#define SDCDIV 0x0c /* Start value for clock divider - 11 R/W */ ++#define SDRSP0 0x10 /* SD card response (31:0) - 32 R */ ++#define SDRSP1 0x14 /* SD card response (63:32) - 32 R */ ++#define SDRSP2 0x18 /* SD card response (95:64) - 32 R */ ++#define SDRSP3 0x1c /* SD card response (127:96) - 32 R */ ++#define SDHSTS 0x20 /* SD host status - 11 R */ ++#define SDVDD 0x30 /* SD card power control - 1 R/W */ ++#define SDEDM 0x34 /* Emergency Debug Mode - 13 R/W */ ++#define SDHCFG 0x38 /* Host configuration - 2 R/W */ ++#define SDHBCT 0x3c /* Host byte count (debug) - 32 R/W */ ++#define SDDATA 0x40 /* Data to/from SD card - 32 R/W */ ++#define SDHBLC 0x50 /* Host block count (SDIO/SDHC) - 9 R/W */ ++ ++#define SDCMD_NEW_FLAG 0x8000 ++#define SDCMD_FAIL_FLAG 0x4000 ++#define SDCMD_BUSYWAIT 0x800 ++#define SDCMD_NO_RESPONSE 0x400 ++#define SDCMD_LONG_RESPONSE 0x200 ++#define SDCMD_WRITE_CMD 0x80 ++#define SDCMD_READ_CMD 0x40 ++#define SDCMD_CMD_MASK 0x3f ++ ++#define SDCDIV_MAX_CDIV 0x7ff ++ ++#define SDHSTS_BUSY_IRPT 0x400 ++#define SDHSTS_BLOCK_IRPT 0x200 ++#define SDHSTS_SDIO_IRPT 0x100 ++#define SDHSTS_REW_TIME_OUT 0x80 ++#define SDHSTS_CMD_TIME_OUT 0x40 ++#define SDHSTS_CRC16_ERROR 0x20 ++#define SDHSTS_CRC7_ERROR 0x10 ++#define SDHSTS_FIFO_ERROR 0x08 ++/* Reserved */ ++/* Reserved */ ++#define SDHSTS_DATA_FLAG 0x01 ++ ++#define SDHSTS_TRANSFER_ERROR_MASK (SDHSTS_CRC7_ERROR|SDHSTS_CRC16_ERROR|SDHSTS_REW_TIME_OUT|SDHSTS_FIFO_ERROR) ++#define SDHSTS_ERROR_MASK (SDHSTS_CMD_TIME_OUT|SDHSTS_TRANSFER_ERROR_MASK) ++ ++#define SDHCFG_BUSY_IRPT_EN (1<<10) ++#define SDHCFG_BLOCK_IRPT_EN (1<<8) ++#define SDHCFG_SDIO_IRPT_EN (1<<5) ++#define SDHCFG_DATA_IRPT_EN (1<<4) ++#define SDHCFG_SLOW_CARD (1<<3) ++#define SDHCFG_WIDE_EXT_BUS (1<<2) ++#define SDHCFG_WIDE_INT_BUS (1<<1) ++#define SDHCFG_REL_CMD_LINE (1<<0) ++ ++#define SDEDM_FORCE_DATA_MODE (1<<19) ++#define SDEDM_CLOCK_PULSE (1<<20) ++#define SDEDM_BYPASS (1<<21) ++ ++#define SDEDM_WRITE_THRESHOLD_SHIFT 9 ++#define SDEDM_READ_THRESHOLD_SHIFT 14 ++#define SDEDM_THRESHOLD_MASK 0x1f ++ ++#define MHZ 1000000 ++ ++ ++struct bcm2835_host { ++ spinlock_t lock; ++ ++ void __iomem *ioaddr; ++ u32 bus_addr; ++ ++ struct mmc_host *mmc; ++ ++ u32 pio_timeout; /* In jiffies */ ++ ++ int clock; /* Current clock speed */ ++ ++ bool slow_card; /* Force 11-bit divisor */ ++ ++ unsigned int max_clk; /* Max possible freq */ ++ ++ struct tasklet_struct finish_tasklet; /* Tasklet structures */ ++ ++ struct timer_list timer; /* Timer for timeouts */ ++ ++ struct timer_list pio_timer; /* PIO error detection timer */ ++ ++ struct sg_mapping_iter sg_miter; /* SG state for PIO */ ++ unsigned int blocks; /* remaining PIO blocks */ ++ ++ int irq; /* Device IRQ */ ++ ++ ++ /* cached registers */ ++ u32 hcfg; ++ u32 cdiv; ++ ++ struct mmc_request *mrq; /* Current request */ ++ struct mmc_command *cmd; /* Current command */ ++ struct mmc_data *data; /* Current data request */ ++ unsigned int data_complete:1; /* Data finished before cmd */ ++ ++ unsigned int flush_fifo:1; /* Drain the fifo when finishing */ ++ ++ unsigned int use_busy:1; /* Wait for busy interrupt */ ++ ++ unsigned int debug:1; /* Enable debug output */ ++ ++ u32 thread_isr; ++ ++ /*DMA part*/ ++ struct dma_chan *dma_chan_rx; /* DMA channel for reads */ ++ struct dma_chan *dma_chan_tx; /* DMA channel for writes */ ++ ++ bool allow_dma; ++ bool have_dma; ++ bool use_dma; ++ /*end of DMA part*/ ++ ++ int max_delay; /* maximum length of time spent waiting */ ++ struct timeval stop_time; /* when the last stop was issued */ ++ u32 delay_after_stop; /* minimum time between stop and subsequent data transfer */ ++ u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */ ++ u32 overclock; /* Current frequency if overclocked, else zero */ ++ u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */ ++}; ++ ++ ++static inline void bcm2835_sdhost_write(struct bcm2835_host *host, u32 val, int reg) ++{ ++ writel(val, host->ioaddr + reg); ++} ++ ++static inline u32 bcm2835_sdhost_read(struct bcm2835_host *host, int reg) ++{ ++ return readl(host->ioaddr + reg); ++} ++ ++static inline u32 bcm2835_sdhost_read_relaxed(struct bcm2835_host *host, int reg) ++{ ++ return readl_relaxed(host->ioaddr + reg); ++} ++ ++static void bcm2835_sdhost_dumpcmd(struct bcm2835_host *host, ++ struct mmc_command *cmd, ++ const char *label) ++{ ++ if (cmd) ++ pr_info("%s:%c%s op %d arg 0x%x flags 0x%x - resp %08x %08x %08x %08x, err %d\n", ++ mmc_hostname(host->mmc), ++ (cmd == host->cmd) ? '>' : ' ', ++ label, cmd->opcode, cmd->arg, cmd->flags, ++ cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3], ++ cmd->error); ++} ++ ++static void bcm2835_sdhost_dumpregs(struct bcm2835_host *host) ++{ ++ bcm2835_sdhost_dumpcmd(host, host->mrq->sbc, "sbc"); ++ bcm2835_sdhost_dumpcmd(host, host->mrq->cmd, "cmd"); ++ if (host->mrq->data) ++ pr_err("%s: data blocks %x blksz %x - err %d\n", ++ mmc_hostname(host->mmc), ++ host->mrq->data->blocks, ++ host->mrq->data->blksz, ++ host->mrq->data->error); ++ bcm2835_sdhost_dumpcmd(host, host->mrq->stop, "stop"); ++ ++ pr_info("%s: =========== REGISTER DUMP ===========\n", ++ mmc_hostname(host->mmc)); ++ ++ pr_info("%s: SDCMD 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDCMD)); ++ pr_info("%s: SDARG 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDARG)); ++ pr_info("%s: SDTOUT 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDTOUT)); ++ pr_info("%s: SDCDIV 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDCDIV)); ++ pr_info("%s: SDRSP0 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDRSP0)); ++ pr_info("%s: SDRSP1 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDRSP1)); ++ pr_info("%s: SDRSP2 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDRSP2)); ++ pr_info("%s: SDRSP3 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDRSP3)); ++ pr_info("%s: SDHSTS 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDHSTS)); ++ pr_info("%s: SDVDD 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDVDD)); ++ pr_info("%s: SDEDM 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDEDM)); ++ pr_info("%s: SDHCFG 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDHCFG)); ++ pr_info("%s: SDHBCT 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDHBCT)); ++ pr_info("%s: SDHBLC 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDHBLC)); ++ ++ pr_info("%s: ===========================================\n", ++ mmc_hostname(host->mmc)); ++} ++ ++ ++static void bcm2835_sdhost_set_power(struct bcm2835_host *host, bool on) ++{ ++ bcm2835_sdhost_write(host, on ? 1 : 0, SDVDD); ++} ++ ++ ++static void bcm2835_sdhost_reset_internal(struct bcm2835_host *host) ++{ ++ u32 temp; ++ ++ bcm2835_sdhost_set_power(host, false); ++ ++ bcm2835_sdhost_write(host, 0, SDCMD); ++ bcm2835_sdhost_write(host, 0, SDARG); ++ bcm2835_sdhost_write(host, 0xf00000, SDTOUT); ++ bcm2835_sdhost_write(host, 0, SDCDIV); ++ bcm2835_sdhost_write(host, 0x7f8, SDHSTS); /* Write 1s to clear */ ++ bcm2835_sdhost_write(host, 0, SDHCFG); ++ bcm2835_sdhost_write(host, 0, SDHBCT); ++ bcm2835_sdhost_write(host, 0, SDHBLC); ++ ++ /* Limit fifo usage due to silicon bug */ ++ temp = bcm2835_sdhost_read(host, SDEDM); ++ temp &= ~((SDEDM_THRESHOLD_MASK<<SDEDM_READ_THRESHOLD_SHIFT) | ++ (SDEDM_THRESHOLD_MASK<<SDEDM_WRITE_THRESHOLD_SHIFT)); ++ temp |= (SAFE_READ_THRESHOLD << SDEDM_READ_THRESHOLD_SHIFT) | ++ (SAFE_WRITE_THRESHOLD << SDEDM_WRITE_THRESHOLD_SHIFT); ++ bcm2835_sdhost_write(host, temp, SDEDM); ++ mdelay(10); ++ bcm2835_sdhost_set_power(host, true); ++ mdelay(10); ++ host->clock = 0; ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ bcm2835_sdhost_write(host, host->cdiv, SDCDIV); ++ mmiowb(); ++} ++ ++ ++static void bcm2835_sdhost_reset(struct mmc_host *mmc) ++{ ++ struct bcm2835_host *host = mmc_priv(mmc); ++ unsigned long flags; ++ if (host->debug) ++ pr_info("%s: reset\n", mmc_hostname(mmc)); ++ spin_lock_irqsave(&host->lock, flags); ++ ++ bcm2835_sdhost_reset_internal(host); ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios); ++ ++static void bcm2835_sdhost_init(struct bcm2835_host *host, int soft) ++{ ++ pr_debug("bcm2835_sdhost_init(%d)\n", soft); ++ ++ /* Set interrupt enables */ ++ host->hcfg = SDHCFG_BUSY_IRPT_EN; ++ ++ bcm2835_sdhost_reset_internal(host); ++ ++ if (soft) { ++ /* force clock reconfiguration */ ++ host->clock = 0; ++ bcm2835_sdhost_set_ios(host->mmc, &host->mmc->ios); ++ } ++} ++ ++static bool bcm2835_sdhost_is_write_complete(struct bcm2835_host *host) ++{ ++ bool write_complete = ((bcm2835_sdhost_read(host, SDEDM) & 0xf) == 1); ++ ++ if (!write_complete) { ++ /* Request an IRQ for the last block */ ++ host->hcfg |= SDHCFG_BLOCK_IRPT_EN; ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ if ((bcm2835_sdhost_read(host, SDEDM) & 0xf) == 1) { ++ /* The write has now completed. Disable the interrupt ++ and clear the status flag */ ++ host->hcfg &= ~SDHCFG_BLOCK_IRPT_EN; ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ bcm2835_sdhost_write(host, SDHSTS_BLOCK_IRPT, SDHSTS); ++ write_complete = true; ++ } ++ } ++ ++ return write_complete; ++} ++ ++static void bcm2835_sdhost_wait_write_complete(struct bcm2835_host *host) ++{ ++ int timediff; ++#ifdef DEBUG ++ static struct timeval start_time; ++ static int max_stall_time = 0; ++ static int total_stall_time = 0; ++ struct timeval before, after; ++ ++ do_gettimeofday(&before); ++ if (max_stall_time == 0) ++ start_time = before; ++#endif ++ ++ timediff = 0; ++ ++ while (1) { ++ u32 edm = bcm2835_sdhost_read(host, SDEDM); ++ if ((edm & 0xf) == 1) ++ break; ++ timediff++; ++ if (timediff > 5000000) { ++#ifdef DEBUG ++ do_gettimeofday(&after); ++ timediff = (after.tv_sec - before.tv_sec)*1000000 + ++ (after.tv_usec - before.tv_usec); ++ ++ pr_err(" wait_write_complete - still waiting after %dus\n", ++ timediff); ++#else ++ pr_err(" wait_write_complete - still waiting after %d retries\n", ++ timediff); ++#endif ++ bcm2835_sdhost_dumpregs(host); ++ host->data->error = -ETIMEDOUT; ++ return; ++ } ++ } ++ ++#ifdef DEBUG ++ do_gettimeofday(&after); ++ timediff = (after.tv_sec - before.tv_sec)*1000000 + (after.tv_usec - before.tv_usec); ++ ++ total_stall_time += timediff; ++ if (timediff > max_stall_time) ++ max_stall_time = timediff; ++ ++ if ((after.tv_sec - start_time.tv_sec) > 10) { ++ pr_debug(" wait_write_complete - max wait %dus, total %dus\n", ++ max_stall_time, total_stall_time); ++ start_time = after; ++ max_stall_time = 0; ++ total_stall_time = 0; ++ } ++#endif ++} ++ ++static void bcm2835_sdhost_finish_data(struct bcm2835_host *host); ++ ++static void bcm2835_sdhost_dma_complete(void *param) ++{ ++ struct bcm2835_host *host = param; ++ struct dma_chan *dma_chan; ++ unsigned long flags; ++ u32 dir_data; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ if (host->data) { ++ bool write_complete; ++ if (USE_BLOCK_IRQ) ++ write_complete = bcm2835_sdhost_is_write_complete(host); ++ else { ++ bcm2835_sdhost_wait_write_complete(host); ++ write_complete = true; ++ } ++ pr_debug("dma_complete() - write_complete=%d\n", ++ write_complete); ++ ++ if (write_complete || (host->data->flags & MMC_DATA_READ)) ++ { ++ if (write_complete) { ++ dma_chan = host->dma_chan_tx; ++ dir_data = DMA_TO_DEVICE; ++ } else { ++ dma_chan = host->dma_chan_rx; ++ dir_data = DMA_FROM_DEVICE; ++ } ++ ++ dma_unmap_sg(dma_chan->device->dev, ++ host->data->sg, host->data->sg_len, ++ dir_data); ++ ++ bcm2835_sdhost_finish_data(host); ++ } ++ } ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static bool data_transfer_wait(struct bcm2835_host *host) ++{ ++ unsigned long timeout = 1000000; ++ while (timeout) ++ { ++ u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS); ++ if (sdhsts & SDHSTS_DATA_FLAG) { ++ bcm2835_sdhost_write(host, SDHSTS_DATA_FLAG, SDHSTS); ++ break; ++ } ++ timeout--; ++ } ++ if (timeout == 0) { ++ pr_err("%s: Data %s timeout\n", ++ mmc_hostname(host->mmc), ++ (host->data->flags & MMC_DATA_READ) ? "read" : "write"); ++ bcm2835_sdhost_dumpregs(host); ++ host->data->error = -ETIMEDOUT; ++ return false; ++ } ++ return true; ++} ++ ++static void bcm2835_sdhost_read_block_pio(struct bcm2835_host *host) ++{ ++ unsigned long flags; ++ size_t blksize, len; ++ u32 *buf; ++ ++ blksize = host->data->blksz; ++ ++ local_irq_save(flags); ++ ++ while (blksize) { ++ if (!sg_miter_next(&host->sg_miter)) ++ BUG(); ++ ++ len = min(host->sg_miter.length, blksize); ++ BUG_ON(len % 4); ++ ++ blksize -= len; ++ host->sg_miter.consumed = len; ++ ++ buf = (u32 *)host->sg_miter.addr; ++ ++ while (len) { ++ if (!data_transfer_wait(host)) ++ break; ++ ++ *(buf++) = bcm2835_sdhost_read(host, SDDATA); ++ len -= 4; ++ } ++ ++ if (host->data->error) ++ break; ++ } ++ ++ sg_miter_stop(&host->sg_miter); ++ ++ local_irq_restore(flags); ++} ++ ++static void bcm2835_sdhost_write_block_pio(struct bcm2835_host *host) ++{ ++ unsigned long flags; ++ size_t blksize, len; ++ u32 *buf; ++ ++ blksize = host->data->blksz; ++ ++ local_irq_save(flags); ++ ++ while (blksize) { ++ if (!sg_miter_next(&host->sg_miter)) ++ BUG(); ++ ++ len = min(host->sg_miter.length, blksize); ++ BUG_ON(len % 4); ++ ++ blksize -= len; ++ host->sg_miter.consumed = len; ++ ++ buf = host->sg_miter.addr; ++ ++ while (len) { ++ if (!data_transfer_wait(host)) ++ break; ++ ++ bcm2835_sdhost_write(host, *(buf++), SDDATA); ++ len -= 4; ++ } ++ ++ if (host->data->error) ++ break; ++ } ++ ++ sg_miter_stop(&host->sg_miter); ++ ++ local_irq_restore(flags); ++} ++ ++ ++static void bcm2835_sdhost_transfer_pio(struct bcm2835_host *host) ++{ ++ u32 sdhsts; ++ bool is_read; ++ BUG_ON(!host->data); ++ ++ is_read = (host->data->flags & MMC_DATA_READ) != 0; ++ if (is_read) ++ bcm2835_sdhost_read_block_pio(host); ++ else ++ bcm2835_sdhost_write_block_pio(host); ++ ++ sdhsts = bcm2835_sdhost_read(host, SDHSTS); ++ if (sdhsts & (SDHSTS_CRC16_ERROR | ++ SDHSTS_CRC7_ERROR | ++ SDHSTS_FIFO_ERROR)) { ++ pr_err("%s: %s transfer error - HSTS %x\n", ++ mmc_hostname(host->mmc), ++ is_read ? "read" : "write", ++ sdhsts); ++ host->data->error = -EILSEQ; ++ } else if ((sdhsts & (SDHSTS_CMD_TIME_OUT | ++ SDHSTS_REW_TIME_OUT))) { ++ pr_err("%s: %s timeout error - HSTS %x\n", ++ mmc_hostname(host->mmc), ++ is_read ? "read" : "write", ++ sdhsts); ++ host->data->error = -ETIMEDOUT; ++ } else if (!is_read && !host->data->error) { ++ /* Start a timer in case a transfer error occurs because ++ there is no error interrupt */ ++ mod_timer(&host->pio_timer, jiffies + host->pio_timeout); ++ } ++} ++ ++ ++static void bcm2835_sdhost_transfer_dma(struct bcm2835_host *host) ++{ ++ u32 len, dir_data, dir_slave; ++ struct dma_async_tx_descriptor *desc = NULL; ++ struct dma_chan *dma_chan; ++ ++ pr_debug("bcm2835_sdhost_transfer_dma()\n"); ++ ++ WARN_ON(!host->data); ++ ++ if (!host->data) ++ return; ++ ++ if (host->data->flags & MMC_DATA_READ) { ++ dma_chan = host->dma_chan_rx; ++ dir_data = DMA_FROM_DEVICE; ++ dir_slave = DMA_DEV_TO_MEM; ++ } else { ++ dma_chan = host->dma_chan_tx; ++ dir_data = DMA_TO_DEVICE; ++ dir_slave = DMA_MEM_TO_DEV; ++ } ++ ++ BUG_ON(!dma_chan->device); ++ BUG_ON(!dma_chan->device->dev); ++ BUG_ON(!host->data->sg); ++ ++ len = dma_map_sg(dma_chan->device->dev, host->data->sg, ++ host->data->sg_len, dir_data); ++ if (len > 0) { ++ desc = dmaengine_prep_slave_sg(dma_chan, host->data->sg, ++ len, dir_slave, ++ DMA_PREP_INTERRUPT | DMA_CTRL_ACK); ++ } else { ++ dev_err(mmc_dev(host->mmc), "dma_map_sg returned zero length\n"); ++ } ++ if (desc) { ++ desc->callback = bcm2835_sdhost_dma_complete; ++ desc->callback_param = host; ++ dmaengine_submit(desc); ++ dma_async_issue_pending(dma_chan); ++ } ++ ++} ++ ++ ++static void bcm2835_sdhost_set_transfer_irqs(struct bcm2835_host *host) ++{ ++ u32 all_irqs = SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN | ++ SDHCFG_BUSY_IRPT_EN; ++ if (host->use_dma) ++ host->hcfg = (host->hcfg & ~all_irqs) | ++ SDHCFG_BUSY_IRPT_EN; ++ else ++ host->hcfg = (host->hcfg & ~all_irqs) | ++ SDHCFG_DATA_IRPT_EN | ++ SDHCFG_BUSY_IRPT_EN; ++ ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++} ++ ++ ++static void bcm2835_sdhost_prepare_data(struct bcm2835_host *host, struct mmc_command *cmd) ++{ ++ struct mmc_data *data = cmd->data; ++ ++ WARN_ON(host->data); ++ ++ if (!data) ++ return; ++ ++ /* Sanity checks */ ++ BUG_ON(data->blksz * data->blocks > 524288); ++ BUG_ON(data->blksz > host->mmc->max_blk_size); ++ BUG_ON(data->blocks > 65535); ++ ++ host->data = data; ++ host->data_complete = 0; ++ host->flush_fifo = 0; ++ host->data->bytes_xfered = 0; ++ ++ host->use_dma = host->have_dma && (data->blocks > host->pio_limit); ++ if (!host->use_dma) { ++ int flags; ++ ++ flags = SG_MITER_ATOMIC; ++ if (data->flags & MMC_DATA_READ) ++ flags |= SG_MITER_TO_SG; ++ else ++ flags |= SG_MITER_FROM_SG; ++ sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); ++ host->blocks = data->blocks; ++ } ++ ++ bcm2835_sdhost_set_transfer_irqs(host); ++ ++ bcm2835_sdhost_write(host, data->blksz, SDHBCT); ++ bcm2835_sdhost_write(host, host->use_dma ? data->blocks : 0, SDHBLC); ++ ++ BUG_ON(!host->data); ++} ++ ++ ++void bcm2835_sdhost_send_command(struct bcm2835_host *host, struct mmc_command *cmd) ++{ ++ u32 sdcmd, sdhsts; ++ unsigned long timeout; ++ int delay; ++ ++ WARN_ON(host->cmd); ++ ++ if (cmd->data) ++ pr_debug("%s: send_command %d 0x%x " ++ "(flags 0x%x) - %s %d*%d\n", ++ mmc_hostname(host->mmc), ++ cmd->opcode, cmd->arg, cmd->flags, ++ (cmd->data->flags & MMC_DATA_READ) ? ++ "read" : "write", cmd->data->blocks, ++ cmd->data->blksz); ++ else ++ pr_debug("%s: send_command %d 0x%x (flags 0x%x)\n", ++ mmc_hostname(host->mmc), ++ cmd->opcode, cmd->arg, cmd->flags); ++ ++ /* Wait max 100 ms */ ++ timeout = 10000; ++ ++ while (bcm2835_sdhost_read(host, SDCMD) & SDCMD_NEW_FLAG) { ++ if (timeout == 0) { ++ pr_err("%s: previous command never completed.\n", ++ mmc_hostname(host->mmc)); ++ bcm2835_sdhost_dumpregs(host); ++ cmd->error = -EIO; ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } ++ timeout--; ++ udelay(10); ++ } ++ ++ delay = (10000 - timeout)/100; ++ if (delay > host->max_delay) { ++ host->max_delay = delay; ++ pr_warning("%s: controller hung for %d ms\n", ++ mmc_hostname(host->mmc), ++ host->max_delay); ++ } ++ ++ timeout = jiffies; ++ if (!cmd->data && cmd->busy_timeout > 9000) ++ timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ; ++ else ++ timeout += 10 * HZ; ++ mod_timer(&host->timer, timeout); ++ ++ host->cmd = cmd; ++ ++ /* Clear any error flags */ ++ sdhsts = bcm2835_sdhost_read(host, SDHSTS); ++ if (sdhsts & SDHSTS_ERROR_MASK) ++ bcm2835_sdhost_write(host, sdhsts, SDHSTS); ++ ++ bcm2835_sdhost_prepare_data(host, cmd); ++ ++ bcm2835_sdhost_write(host, cmd->arg, SDARG); ++ ++ if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) { ++ pr_err("%s: unsupported response type!\n", ++ mmc_hostname(host->mmc)); ++ cmd->error = -EINVAL; ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } ++ ++ sdcmd = cmd->opcode & SDCMD_CMD_MASK; ++ ++ if (!(cmd->flags & MMC_RSP_PRESENT)) ++ sdcmd |= SDCMD_NO_RESPONSE; ++ else { ++ if (cmd->flags & MMC_RSP_136) ++ sdcmd |= SDCMD_LONG_RESPONSE; ++ if (cmd->flags & MMC_RSP_BUSY) { ++ sdcmd |= SDCMD_BUSYWAIT; ++ host->use_busy = 1; ++ } ++ } ++ ++ if (cmd->data) { ++ if (host->delay_after_stop) { ++ struct timeval now; ++ int time_since_stop; ++ do_gettimeofday(&now); ++ time_since_stop = (now.tv_sec - host->stop_time.tv_sec); ++ if (time_since_stop < 2) { ++ /* Possibly less than one second */ ++ time_since_stop = time_since_stop * 1000000 + ++ (now.tv_usec - host->stop_time.tv_usec); ++ if (time_since_stop < host->delay_after_stop) ++ udelay(host->delay_after_stop - ++ time_since_stop); ++ } ++ } ++ ++ if (cmd->data->flags & MMC_DATA_WRITE) ++ sdcmd |= SDCMD_WRITE_CMD; ++ if (cmd->data->flags & MMC_DATA_READ) ++ sdcmd |= SDCMD_READ_CMD; ++ } ++ ++ bcm2835_sdhost_write(host, sdcmd | SDCMD_NEW_FLAG, SDCMD); ++} ++ ++ ++static void bcm2835_sdhost_finish_command(struct bcm2835_host *host); ++static void bcm2835_sdhost_transfer_complete(struct bcm2835_host *host); ++ ++static void bcm2835_sdhost_finish_data(struct bcm2835_host *host) ++{ ++ struct mmc_data *data; ++ ++ data = host->data; ++ BUG_ON(!data); ++ ++ pr_debug("finish_data(error %d, stop %d, sbc %d)\n", ++ data->error, data->stop ? 1 : 0, ++ host->mrq->sbc ? 1 : 0); ++ ++ host->hcfg &= ~(SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN); ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ ++ if (data->error) { ++ data->bytes_xfered = 0; ++ } else ++ data->bytes_xfered = data->blksz * data->blocks; ++ ++ host->data_complete = 1; ++ ++ if (host->cmd) { ++ /* ++ * Data managed to finish before the ++ * command completed. Make sure we do ++ * things in the proper order. ++ */ ++ pr_debug("Finished early - HSTS %x\n", ++ bcm2835_sdhost_read(host, SDHSTS)); ++ } ++ else ++ bcm2835_sdhost_transfer_complete(host); ++} ++ ++ ++static void bcm2835_sdhost_transfer_complete(struct bcm2835_host *host) ++{ ++ struct mmc_data *data; ++ ++ BUG_ON(host->cmd); ++ BUG_ON(!host->data); ++ BUG_ON(!host->data_complete); ++ ++ data = host->data; ++ host->data = NULL; ++ ++ pr_debug("transfer_complete(error %d, stop %d)\n", ++ data->error, data->stop ? 1 : 0); ++ ++ /* ++ * Need to send CMD12 if - ++ * a) open-ended multiblock transfer (no CMD23) ++ * b) error in multiblock transfer ++ */ ++ if (data->stop && ++ (data->error || ++ !host->mrq->sbc)) { ++ host->flush_fifo = 1; ++ bcm2835_sdhost_send_command(host, data->stop); ++ if (host->delay_after_stop) ++ do_gettimeofday(&host->stop_time); ++ if (!host->use_busy) ++ bcm2835_sdhost_finish_command(host); ++ } else { ++ tasklet_schedule(&host->finish_tasklet); ++ } ++} ++ ++static void bcm2835_sdhost_finish_command(struct bcm2835_host *host) ++{ ++ u32 sdcmd; ++ unsigned long timeout; ++#ifdef DEBUG ++ struct timeval before, after; ++ int timediff = 0; ++#endif ++ ++ pr_debug("finish_command(%x)\n", bcm2835_sdhost_read(host, SDCMD)); ++ ++ BUG_ON(!host->cmd || !host->mrq); ++ ++#ifdef DEBUG ++ do_gettimeofday(&before); ++#endif ++ /* Wait max 100 ms */ ++ timeout = 10000; ++ for (sdcmd = bcm2835_sdhost_read(host, SDCMD); ++ (sdcmd & SDCMD_NEW_FLAG) && timeout; ++ timeout--) { ++ if (host->flush_fifo) { ++ while (bcm2835_sdhost_read(host, SDHSTS) & ++ SDHSTS_DATA_FLAG) ++ (void)bcm2835_sdhost_read(host, SDDATA); ++ } ++ udelay(10); ++ sdcmd = bcm2835_sdhost_read(host, SDCMD); ++ } ++#ifdef DEBUG ++ do_gettimeofday(&after); ++ timediff = (after.tv_sec - before.tv_sec)*1000000 + ++ (after.tv_usec - before.tv_usec); ++ ++ pr_debug(" finish_command - waited %dus\n", timediff); ++#endif ++ ++ if (timeout == 0) { ++ pr_err("%s: command never completed.\n", ++ mmc_hostname(host->mmc)); ++ bcm2835_sdhost_dumpregs(host); ++ host->cmd->error = -EIO; ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } ++ ++ if (host->flush_fifo) { ++ for (timeout = 100; ++ (bcm2835_sdhost_read(host, SDHSTS) & SDHSTS_DATA_FLAG) && timeout; ++ timeout--) { ++ (void)bcm2835_sdhost_read(host, SDDATA); ++ } ++ host->flush_fifo = 0; ++ if (timeout == 0) { ++ pr_err("%s: FIFO never drained.\n", ++ mmc_hostname(host->mmc)); ++ bcm2835_sdhost_dumpregs(host); ++ host->cmd->error = -EIO; ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } ++ } ++ ++ /* Check for errors */ ++ if (sdcmd & SDCMD_FAIL_FLAG) ++ { ++ u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS); ++ ++ if (host->debug) ++ pr_info("%s: error detected - CMD %x, HSTS %03x, EDM %x\n", ++ mmc_hostname(host->mmc), sdcmd, sdhsts, ++ bcm2835_sdhost_read(host, SDEDM)); ++ ++ if ((sdhsts & SDHSTS_CRC7_ERROR) && ++ (host->cmd->opcode == 1)) { ++ if (host->debug) ++ pr_info("%s: ignoring CRC7 error for CMD1\n", ++ mmc_hostname(host->mmc)); ++ } else { ++ if (sdhsts & SDHSTS_CMD_TIME_OUT) { ++ if (host->debug) ++ pr_err("%s: command %d timeout\n", ++ mmc_hostname(host->mmc), ++ host->cmd->opcode); ++ host->cmd->error = -ETIMEDOUT; ++ } else { ++ pr_err("%s: unexpected command %d error\n", ++ mmc_hostname(host->mmc), ++ host->cmd->opcode); ++ bcm2835_sdhost_dumpregs(host); ++ host->cmd->error = -EIO; ++ } ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } ++ } ++ ++ if (host->cmd->flags & MMC_RSP_PRESENT) { ++ if (host->cmd->flags & MMC_RSP_136) { ++ int i; ++ for (i = 0; i < 4; i++) ++ host->cmd->resp[3 - i] = bcm2835_sdhost_read(host, SDRSP0 + i*4); ++ pr_debug("%s: finish_command %08x %08x %08x %08x\n", ++ mmc_hostname(host->mmc), ++ host->cmd->resp[0], host->cmd->resp[1], host->cmd->resp[2], host->cmd->resp[3]); ++ } else { ++ host->cmd->resp[0] = bcm2835_sdhost_read(host, SDRSP0); ++ pr_debug("%s: finish_command %08x\n", ++ mmc_hostname(host->mmc), ++ host->cmd->resp[0]); ++ } ++ } ++ ++ host->cmd->error = 0; ++ ++ if (host->cmd == host->mrq->sbc) { ++ /* Finished CMD23, now send actual command. */ ++ host->cmd = NULL; ++ bcm2835_sdhost_send_command(host, host->mrq->cmd); ++ ++ if (host->cmd->data && host->use_dma) ++ /* DMA transfer starts now, PIO starts after irq */ ++ bcm2835_sdhost_transfer_dma(host); ++ ++ if (!host->use_busy) ++ bcm2835_sdhost_finish_command(host); ++ } else if (host->cmd == host->mrq->stop) ++ /* Finished CMD12 */ ++ tasklet_schedule(&host->finish_tasklet); ++ else { ++ /* Processed actual command. */ ++ host->cmd = NULL; ++ if (!host->data) ++ tasklet_schedule(&host->finish_tasklet); ++ else if (host->data_complete) ++ bcm2835_sdhost_transfer_complete(host); ++ } ++} ++ ++static void bcm2835_sdhost_timeout(unsigned long data) ++{ ++ struct bcm2835_host *host; ++ unsigned long flags; ++ ++ host = (struct bcm2835_host *)data; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ if (host->mrq) { ++ pr_err("%s: timeout waiting for hardware interrupt.\n", ++ mmc_hostname(host->mmc)); ++ bcm2835_sdhost_dumpregs(host); ++ ++ if (host->data) { ++ host->data->error = -ETIMEDOUT; ++ bcm2835_sdhost_finish_data(host); ++ } else { ++ if (host->cmd) ++ host->cmd->error = -ETIMEDOUT; ++ else ++ host->mrq->cmd->error = -ETIMEDOUT; ++ ++ pr_debug("timeout_timer tasklet_schedule\n"); ++ tasklet_schedule(&host->finish_tasklet); ++ } ++ } ++ ++ mmiowb(); ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_sdhost_pio_timeout(unsigned long data) ++{ ++ struct bcm2835_host *host; ++ unsigned long flags; ++ ++ host = (struct bcm2835_host *)data; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ if (host->data) { ++ u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS); ++ ++ if (sdhsts & SDHSTS_REW_TIME_OUT) { ++ pr_err("%s: transfer timeout\n", ++ mmc_hostname(host->mmc)); ++ if (host->debug) ++ bcm2835_sdhost_dumpregs(host); ++ } else { ++ pr_err("%s: unexpected transfer timeout\n", ++ mmc_hostname(host->mmc)); ++ bcm2835_sdhost_dumpregs(host); ++ } ++ ++ bcm2835_sdhost_write(host, SDHSTS_TRANSFER_ERROR_MASK, ++ SDHSTS); ++ ++ host->data->error = -ETIMEDOUT; ++ ++ bcm2835_sdhost_finish_data(host); ++ } ++ ++ mmiowb(); ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_sdhost_enable_sdio_irq_nolock(struct bcm2835_host *host, int enable) ++{ ++ if (enable) ++ host->hcfg |= SDHCFG_SDIO_IRPT_EN; ++ else ++ host->hcfg &= ~SDHCFG_SDIO_IRPT_EN; ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ mmiowb(); ++} ++ ++static void bcm2835_sdhost_enable_sdio_irq(struct mmc_host *mmc, int enable) ++{ ++ struct bcm2835_host *host = mmc_priv(mmc); ++ unsigned long flags; ++ ++ pr_debug("%s: enable_sdio_irq(%d)\n", mmc_hostname(mmc), enable); ++ spin_lock_irqsave(&host->lock, flags); ++ bcm2835_sdhost_enable_sdio_irq_nolock(host, enable); ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static u32 bcm2835_sdhost_busy_irq(struct bcm2835_host *host, u32 intmask) ++{ ++ const u32 handled = (SDHSTS_REW_TIME_OUT | SDHSTS_CMD_TIME_OUT | ++ SDHSTS_CRC16_ERROR | SDHSTS_CRC7_ERROR | ++ SDHSTS_FIFO_ERROR); ++ ++ if (!host->cmd) { ++ pr_err("%s: got command busy interrupt 0x%08x even " ++ "though no command operation was in progress.\n", ++ mmc_hostname(host->mmc), (unsigned)intmask); ++ bcm2835_sdhost_dumpregs(host); ++ return 0; ++ } ++ ++ if (!host->use_busy) { ++ pr_err("%s: got command busy interrupt 0x%08x even " ++ "though not expecting one.\n", ++ mmc_hostname(host->mmc), (unsigned)intmask); ++ bcm2835_sdhost_dumpregs(host); ++ return 0; ++ } ++ host->use_busy = 0; ++ ++ if (intmask & SDHSTS_ERROR_MASK) ++ { ++ pr_err("sdhost_busy_irq: intmask %x, data %p\n", intmask, host->mrq->data); ++ if (intmask & SDHSTS_CRC7_ERROR) ++ host->cmd->error = -EILSEQ; ++ else if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR)) { ++ if (host->mrq->data) ++ host->mrq->data->error = -EILSEQ; ++ else ++ host->cmd->error = -EILSEQ; ++ } else if (intmask & SDHSTS_REW_TIME_OUT) { ++ if (host->mrq->data) ++ host->mrq->data->error = -ETIMEDOUT; ++ else ++ host->cmd->error = -ETIMEDOUT; ++ } else if (intmask & SDHSTS_CMD_TIME_OUT) ++ host->cmd->error = -ETIMEDOUT; ++ ++ bcm2835_sdhost_dumpregs(host); ++ tasklet_schedule(&host->finish_tasklet); ++ } ++ else ++ bcm2835_sdhost_finish_command(host); ++ ++ return handled; ++} ++ ++static u32 bcm2835_sdhost_data_irq(struct bcm2835_host *host, u32 intmask) ++{ ++ const u32 handled = (SDHSTS_REW_TIME_OUT | ++ SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR); ++ ++ /* There are no dedicated data/space available interrupt ++ status bits, so it is necessary to use the single shared ++ data/space available FIFO status bits. It is therefore not ++ an error to get here when there is no data transfer in ++ progress. */ ++ if (!host->data) ++ return 0; ++ ++ if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR | ++ SDHSTS_REW_TIME_OUT)) { ++ if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR)) ++ host->data->error = -EILSEQ; ++ else ++ host->data->error = -ETIMEDOUT; ++ ++ bcm2835_sdhost_dumpregs(host); ++ tasklet_schedule(&host->finish_tasklet); ++ return handled; ++ } ++ ++ /* Use the block interrupt for writes after the first block */ ++ if (host->data->flags & MMC_DATA_WRITE) { ++ host->hcfg &= ~(SDHCFG_DATA_IRPT_EN); ++ host->hcfg |= SDHCFG_BLOCK_IRPT_EN; ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ if (host->data->error) ++ bcm2835_sdhost_finish_data(host); ++ else ++ bcm2835_sdhost_transfer_pio(host); ++ } else { ++ if (!host->data->error) { ++ bcm2835_sdhost_transfer_pio(host); ++ host->blocks--; ++ } ++ if ((host->blocks == 0) || host->data->error) ++ bcm2835_sdhost_finish_data(host); ++ } ++ ++ return handled; ++} ++ ++static u32 bcm2835_sdhost_block_irq(struct bcm2835_host *host, u32 intmask) ++{ ++ struct dma_chan *dma_chan; ++ u32 dir_data; ++ const u32 handled = (SDHSTS_REW_TIME_OUT | ++ SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR); ++ ++ if (!host->data) { ++ pr_err("%s: got block interrupt 0x%08x even " ++ "though no data operation was in progress.\n", ++ mmc_hostname(host->mmc), (unsigned)intmask); ++ bcm2835_sdhost_dumpregs(host); ++ return handled; ++ } ++ ++ if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR | ++ SDHSTS_REW_TIME_OUT)) { ++ if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR)) ++ host->data->error = -EILSEQ; ++ else ++ host->data->error = -ETIMEDOUT; ++ ++ if (host->debug) ++ bcm2835_sdhost_dumpregs(host); ++ tasklet_schedule(&host->finish_tasklet); ++ return handled; ++ } ++ ++ if (!host->use_dma) { ++ BUG_ON(!host->blocks); ++ host->blocks--; ++ if ((host->blocks == 0) || host->data->error) { ++ /* Cancel the timer */ ++ del_timer(&host->pio_timer); ++ ++ bcm2835_sdhost_finish_data(host); ++ } else { ++ bcm2835_sdhost_transfer_pio(host); ++ ++ /* Reset the timer */ ++ mod_timer(&host->pio_timer, ++ jiffies + host->pio_timeout); ++ } ++ } else if (host->data->flags & MMC_DATA_WRITE) { ++ dma_chan = host->dma_chan_tx; ++ dir_data = DMA_TO_DEVICE; ++ dma_unmap_sg(dma_chan->device->dev, ++ host->data->sg, host->data->sg_len, ++ dir_data); ++ ++ bcm2835_sdhost_finish_data(host); ++ } ++ ++ return handled; ++} ++ ++ ++static irqreturn_t bcm2835_sdhost_irq(int irq, void *dev_id) ++{ ++ irqreturn_t result = IRQ_NONE; ++ struct bcm2835_host *host = dev_id; ++ u32 unexpected = 0, early = 0; ++ int loops = 0; ++ ++ spin_lock(&host->lock); ++ ++ for (loops = 0; loops < 1; loops++) { ++ u32 intmask, handled; ++ ++ intmask = bcm2835_sdhost_read(host, SDHSTS); ++ handled = intmask & (SDHSTS_BUSY_IRPT | ++ SDHSTS_BLOCK_IRPT | ++ SDHSTS_SDIO_IRPT | ++ SDHSTS_DATA_FLAG); ++ if ((handled == SDHSTS_DATA_FLAG) && ++ (loops == 0) && !host->data) { ++ pr_err("%s: sdhost_irq data interrupt 0x%08x even " ++ "though no data operation was in progress.\n", ++ mmc_hostname(host->mmc), ++ (unsigned)intmask); ++ ++ bcm2835_sdhost_dumpregs(host); ++ } ++ ++ if (!handled) ++ break; ++ ++ if (loops) ++ early |= handled; ++ ++ result = IRQ_HANDLED; ++ ++ /* Clear all interrupts and notifications */ ++ bcm2835_sdhost_write(host, intmask, SDHSTS); ++ ++ if (intmask & SDHSTS_BUSY_IRPT) ++ handled |= bcm2835_sdhost_busy_irq(host, intmask); ++ ++ /* There is no true data interrupt status bit, so it is ++ necessary to qualify the data flag with the interrupt ++ enable bit */ ++ if ((intmask & SDHSTS_DATA_FLAG) && ++ (host->hcfg & SDHCFG_DATA_IRPT_EN)) ++ handled |= bcm2835_sdhost_data_irq(host, intmask); ++ ++ if (intmask & SDHSTS_BLOCK_IRPT) ++ handled |= bcm2835_sdhost_block_irq(host, intmask); ++ ++ if (intmask & SDHSTS_SDIO_IRPT) { ++ bcm2835_sdhost_enable_sdio_irq_nolock(host, false); ++ host->thread_isr |= SDHSTS_SDIO_IRPT; ++ result = IRQ_WAKE_THREAD; ++ } ++ ++ unexpected |= (intmask & ~handled); ++ } ++ ++ mmiowb(); ++ ++ spin_unlock(&host->lock); ++ ++ if (early) ++ pr_debug("%s: early %x (loops %d)\n", ++ mmc_hostname(host->mmc), early, loops); ++ ++ if (unexpected) { ++ pr_err("%s: unexpected interrupt 0x%08x.\n", ++ mmc_hostname(host->mmc), unexpected); ++ bcm2835_sdhost_dumpregs(host); ++ } ++ ++ return result; ++} ++ ++static irqreturn_t bcm2835_sdhost_thread_irq(int irq, void *dev_id) ++{ ++ struct bcm2835_host *host = dev_id; ++ unsigned long flags; ++ u32 isr; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ isr = host->thread_isr; ++ host->thread_isr = 0; ++ spin_unlock_irqrestore(&host->lock, flags); ++ ++ if (isr & SDHSTS_SDIO_IRPT) { ++ sdio_run_irqs(host->mmc); ++ ++/* Is this necessary? Why re-enable an interrupt which is enabled? ++ spin_lock_irqsave(&host->lock, flags); ++ if (host->flags & SDHSTS_SDIO_IRPT_ENABLED) ++ bcm2835_sdhost_enable_sdio_irq_nolock(host, true); ++ spin_unlock_irqrestore(&host->lock, flags); ++*/ ++ } ++ ++ return isr ? IRQ_HANDLED : IRQ_NONE; ++} ++ ++ ++ ++void bcm2835_sdhost_set_clock(struct bcm2835_host *host, unsigned int clock) ++{ ++ int div = 0; /* Initialized for compiler warning */ ++ unsigned int input_clock = clock; ++ ++ if (host->debug) ++ pr_info("%s: set_clock(%d)\n", mmc_hostname(host->mmc), clock); ++ ++ if ((host->overclock_50 > 50) && ++ (clock == 50*MHZ)) { ++ clock = host->overclock_50 * MHZ + (MHZ - 1); ++ } ++ ++ /* The SDCDIV register has 11 bits, and holds (div - 2). ++ But in data mode the max is 50MHz wihout a minimum, and only the ++ bottom 3 bits are used. Since the switch over is automatic (unless ++ we have marked the card as slow...), chosen values have to make ++ sense in both modes. ++ Ident mode must be 100-400KHz, so can range check the requested ++ clock. CMD15 must be used to return to data mode, so this can be ++ monitored. ++ ++ clock 250MHz -> 0->125MHz, 1->83.3MHz, 2->62.5MHz, 3->50.0MHz ++ 4->41.7MHz, 5->35.7MHz, 6->31.3MHz, 7->27.8MHz ++ ++ 623->400KHz/27.8MHz ++ reset value (507)->491159/50MHz ++ ++ BUT, the 3-bit clock divisor in data mode is too small if the ++ core clock is higher than 250MHz, so instead use the SLOW_CARD ++ configuration bit to force the use of the ident clock divisor ++ at all times. ++ */ ++ ++ host->mmc->actual_clock = 0; ++ ++ if (clock < 100000) { ++ /* Can't stop the clock, but make it as slow as possible ++ * to show willing ++ */ ++ host->cdiv = SDCDIV_MAX_CDIV; ++ bcm2835_sdhost_write(host, host->cdiv, SDCDIV); ++ return; ++ } ++ ++ div = host->max_clk / clock; ++ if (div < 2) ++ div = 2; ++ if ((host->max_clk / div) > clock) ++ div++; ++ div -= 2; ++ ++ if (div > SDCDIV_MAX_CDIV) ++ div = SDCDIV_MAX_CDIV; ++ ++ clock = host->max_clk / (div + 2); ++ host->mmc->actual_clock = clock; ++ ++ if (clock > input_clock) { ++ /* Save the closest value, to make it easier ++ to reduce in the event of error */ ++ host->overclock_50 = (clock/MHZ); ++ ++ if (clock != host->overclock) { ++ pr_warn("%s: overclocking to %dHz\n", ++ mmc_hostname(host->mmc), clock); ++ host->overclock = clock; ++ } ++ } ++ else if (host->overclock) ++ { ++ host->overclock = 0; ++ if (clock == 50 * MHZ) ++ pr_warn("%s: cancelling overclock\n", ++ mmc_hostname(host->mmc)); ++ } ++ ++ host->cdiv = div; ++ bcm2835_sdhost_write(host, host->cdiv, SDCDIV); ++ ++ /* Set the timeout to 500ms */ ++ bcm2835_sdhost_write(host, host->mmc->actual_clock/2, SDTOUT); ++ ++ if (host->debug) ++ pr_info("%s: clock=%d -> max_clk=%d, cdiv=%x (actual clock %d)\n", ++ mmc_hostname(host->mmc), input_clock, ++ host->max_clk, host->cdiv, host->mmc->actual_clock); ++} ++ ++static void bcm2835_sdhost_request(struct mmc_host *mmc, struct mmc_request *mrq) ++{ ++ struct bcm2835_host *host; ++ unsigned long flags; ++ ++ host = mmc_priv(mmc); ++ ++ if (host->debug) { ++ struct mmc_command *cmd = mrq->cmd; ++ BUG_ON(!cmd); ++ if (cmd->data) ++ pr_info("%s: cmd %d 0x%x (flags 0x%x) - %s %d*%d\n", ++ mmc_hostname(mmc), ++ cmd->opcode, cmd->arg, cmd->flags, ++ (cmd->data->flags & MMC_DATA_READ) ? ++ "read" : "write", cmd->data->blocks, ++ cmd->data->blksz); ++ else ++ pr_info("%s: cmd %d 0x%x (flags 0x%x)\n", ++ mmc_hostname(mmc), ++ cmd->opcode, cmd->arg, cmd->flags); ++ } ++ ++ /* Reset the error statuses in case this is a retry */ ++ if (mrq->cmd) ++ mrq->cmd->error = 0; ++ if (mrq->data) ++ mrq->data->error = 0; ++ if (mrq->stop) ++ mrq->stop->error = 0; ++ ++ if (mrq->data && !is_power_of_2(mrq->data->blksz)) { ++ pr_err("%s: unsupported block size (%d bytes)\n", ++ mmc_hostname(mmc), mrq->data->blksz); ++ mrq->cmd->error = -EINVAL; ++ mmc_request_done(mmc, mrq); ++ return; ++ } ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ WARN_ON(host->mrq != NULL); ++ ++ host->mrq = mrq; ++ ++ if (mrq->sbc) ++ bcm2835_sdhost_send_command(host, mrq->sbc); ++ else ++ bcm2835_sdhost_send_command(host, mrq->cmd); ++ ++ mmiowb(); ++ spin_unlock_irqrestore(&host->lock, flags); ++ ++ if (!mrq->sbc && mrq->cmd->data && host->use_dma) ++ /* DMA transfer starts now, PIO starts after irq */ ++ bcm2835_sdhost_transfer_dma(host); ++ ++ if (!host->use_busy) ++ bcm2835_sdhost_finish_command(host); ++} ++ ++ ++static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) ++{ ++ ++ struct bcm2835_host *host = mmc_priv(mmc); ++ unsigned long flags; ++ ++ if (host->debug) ++ pr_info("%s: ios clock %d, pwr %d, bus_width %d, " ++ "timing %d, vdd %d, drv_type %d\n", ++ mmc_hostname(mmc), ++ ios->clock, ios->power_mode, ios->bus_width, ++ ios->timing, ios->signal_voltage, ios->drv_type); ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ if (!ios->clock || ios->clock != host->clock) { ++ bcm2835_sdhost_set_clock(host, ios->clock); ++ host->clock = ios->clock; ++ } ++ ++ /* set bus width */ ++ host->hcfg &= ~SDHCFG_WIDE_EXT_BUS; ++ if (ios->bus_width == MMC_BUS_WIDTH_4) ++ host->hcfg |= SDHCFG_WIDE_EXT_BUS; ++ ++ host->hcfg |= SDHCFG_WIDE_INT_BUS; ++ ++ /* Disable clever clock switching, to cope with fast core clocks */ ++ host->hcfg |= SDHCFG_SLOW_CARD; ++ ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ ++ mmiowb(); ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static int bcm2835_sdhost_multi_io_quirk(struct mmc_card *card, ++ unsigned int direction, ++ u32 blk_pos, int blk_size) ++{ ++ /* There is a bug in the host controller hardware that makes ++ reading the final sector of the card as part of a multiple read ++ problematic. Detect that case and shorten the read accordingly. ++ */ ++ /* csd.capacity is in weird units - convert to sectors */ ++ u32 card_sectors = (card->csd.capacity << (card->csd.read_blkbits - 9)); ++ ++ if ((direction == MMC_DATA_READ) && ++ ((blk_pos + blk_size) == card_sectors)) ++ blk_size--; ++ ++ return blk_size; ++} ++ ++ ++static struct mmc_host_ops bcm2835_sdhost_ops = { ++ .request = bcm2835_sdhost_request, ++ .set_ios = bcm2835_sdhost_set_ios, ++ .enable_sdio_irq = bcm2835_sdhost_enable_sdio_irq, ++ .hw_reset = bcm2835_sdhost_reset, ++ .multi_io_quirk = bcm2835_sdhost_multi_io_quirk, ++}; ++ ++ ++static void bcm2835_sdhost_tasklet_finish(unsigned long param) ++{ ++ struct bcm2835_host *host; ++ unsigned long flags; ++ struct mmc_request *mrq; ++ ++ host = (struct bcm2835_host *)param; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ /* ++ * If this tasklet gets rescheduled while running, it will ++ * be run again afterwards but without any active request. ++ */ ++ if (!host->mrq) { ++ spin_unlock_irqrestore(&host->lock, flags); ++ return; ++ } ++ ++ del_timer(&host->timer); ++ ++ mrq = host->mrq; ++ ++ /* Drop the overclock after any data corruption, or after any ++ error overclocked */ ++ if (host->overclock) { ++ if ((mrq->cmd && mrq->cmd->error) || ++ (mrq->data && mrq->data->error) || ++ (mrq->stop && mrq->stop->error)) { ++ host->overclock_50--; ++ pr_warn("%s: reducing overclock due to errors\n", ++ mmc_hostname(host->mmc)); ++ bcm2835_sdhost_set_clock(host,50*MHZ); ++ mrq->cmd->error = -EILSEQ; ++ mrq->cmd->retries = 1; ++ } ++ } ++ ++ host->mrq = NULL; ++ host->cmd = NULL; ++ host->data = NULL; ++ ++ mmiowb(); ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++ mmc_request_done(host->mmc, mrq); ++} ++ ++ ++ ++int bcm2835_sdhost_add_host(struct bcm2835_host *host) ++{ ++ struct mmc_host *mmc; ++ struct dma_slave_config cfg; ++ char pio_limit_string[20]; ++ int ret; ++ ++ mmc = host->mmc; ++ ++ bcm2835_sdhost_reset_internal(host); ++ ++ mmc->f_max = host->max_clk; ++ mmc->f_min = host->max_clk / SDCDIV_MAX_CDIV; ++ ++ mmc->max_busy_timeout = (~(unsigned int)0)/(mmc->f_max/1000); ++ ++ pr_debug("f_max %d, f_min %d, max_busy_timeout %d\n", ++ mmc->f_max, mmc->f_min, mmc->max_busy_timeout); ++ ++ /* host controller capabilities */ ++ mmc->caps |= /* MMC_CAP_SDIO_IRQ |*/ MMC_CAP_4_BIT_DATA | ++ MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED | ++ MMC_CAP_NEEDS_POLL | MMC_CAP_HW_RESET | MMC_CAP_ERASE | ++ (ALLOW_CMD23 * MMC_CAP_CMD23); ++ ++ spin_lock_init(&host->lock); ++ ++ if (host->allow_dma) { ++ if (IS_ERR_OR_NULL(host->dma_chan_tx) || ++ IS_ERR_OR_NULL(host->dma_chan_rx)) { ++ pr_err("%s: unable to initialise DMA channels. " ++ "Falling back to PIO\n", ++ mmc_hostname(mmc)); ++ host->have_dma = false; ++ } else { ++ host->have_dma = true; ++ ++ cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ cfg.slave_id = 13; /* DREQ channel */ ++ ++ cfg.direction = DMA_MEM_TO_DEV; ++ cfg.src_addr = 0; ++ cfg.dst_addr = host->bus_addr + SDDATA; ++ ret = dmaengine_slave_config(host->dma_chan_tx, &cfg); ++ ++ cfg.direction = DMA_DEV_TO_MEM; ++ cfg.src_addr = host->bus_addr + SDDATA; ++ cfg.dst_addr = 0; ++ ret = dmaengine_slave_config(host->dma_chan_rx, &cfg); ++ } ++ } else { ++ host->have_dma = false; ++ } ++ ++ mmc->max_segs = 128; ++ mmc->max_req_size = 524288; ++ mmc->max_seg_size = mmc->max_req_size; ++ mmc->max_blk_size = 512; ++ mmc->max_blk_count = 65535; ++ ++ /* report supported voltage ranges */ ++ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; ++ ++ tasklet_init(&host->finish_tasklet, ++ bcm2835_sdhost_tasklet_finish, (unsigned long)host); ++ ++ setup_timer(&host->timer, bcm2835_sdhost_timeout, ++ (unsigned long)host); ++ ++ setup_timer(&host->pio_timer, bcm2835_sdhost_pio_timeout, ++ (unsigned long)host); ++ ++ bcm2835_sdhost_init(host, 0); ++ ret = request_threaded_irq(host->irq, bcm2835_sdhost_irq, ++ bcm2835_sdhost_thread_irq, ++ IRQF_SHARED, mmc_hostname(mmc), host); ++ if (ret) { ++ pr_err("%s: failed to request IRQ %d: %d\n", ++ mmc_hostname(mmc), host->irq, ret); ++ goto untasklet; ++ } ++ ++ mmiowb(); ++ mmc_add_host(mmc); ++ ++ pio_limit_string[0] = '\0'; ++ if (host->have_dma && (host->pio_limit > 0)) ++ sprintf(pio_limit_string, " (>%d)", host->pio_limit); ++ pr_info("%s: %s loaded - DMA %s%s\n", ++ mmc_hostname(mmc), DRIVER_NAME, ++ host->have_dma ? "enabled" : "disabled", ++ pio_limit_string); ++ ++ return 0; ++ ++untasklet: ++ tasklet_kill(&host->finish_tasklet); ++ ++ return ret; ++} ++ ++static int bcm2835_sdhost_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct device_node *node = dev->of_node; ++ struct clk *clk; ++ struct resource *iomem; ++ struct bcm2835_host *host; ++ struct mmc_host *mmc; ++ const __be32 *addr; ++ int ret; ++ ++ pr_debug("bcm2835_sdhost_probe\n"); ++ mmc = mmc_alloc_host(sizeof(*host), dev); ++ if (!mmc) ++ return -ENOMEM; ++ ++ mmc->ops = &bcm2835_sdhost_ops; ++ host = mmc_priv(mmc); ++ host->mmc = mmc; ++ host->pio_timeout = msecs_to_jiffies(500); ++ host->max_delay = 1; /* Warn if over 1ms */ ++ spin_lock_init(&host->lock); ++ ++ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ host->ioaddr = devm_ioremap_resource(dev, iomem); ++ if (IS_ERR(host->ioaddr)) { ++ ret = PTR_ERR(host->ioaddr); ++ goto err; ++ } ++ ++ addr = of_get_address(node, 0, NULL, NULL); ++ if (!addr) { ++ dev_err(dev, "could not get DMA-register address\n"); ++ return -ENODEV; ++ } ++ host->bus_addr = be32_to_cpup(addr); ++ pr_debug(" - ioaddr %lx, iomem->start %lx, bus_addr %lx\n", ++ (unsigned long)host->ioaddr, ++ (unsigned long)iomem->start, ++ (unsigned long)host->bus_addr); ++ ++ host->allow_dma = ALLOW_DMA; ++ ++ if (node) { ++ /* Read any custom properties */ ++ of_property_read_u32(node, ++ "brcm,delay-after-stop", ++ &host->delay_after_stop); ++ of_property_read_u32(node, ++ "brcm,overclock-50", ++ &host->overclock_50); ++ of_property_read_u32(node, ++ "brcm,pio-limit", ++ &host->pio_limit); ++ host->allow_dma = ALLOW_DMA && ++ !of_property_read_bool(node, "brcm,force-pio"); ++ host->debug = of_property_read_bool(node, "brcm,debug"); ++ } ++ ++ if (host->allow_dma) { ++ if (node) { ++ host->dma_chan_tx = ++ dma_request_slave_channel(dev, "tx"); ++ host->dma_chan_rx = ++ dma_request_slave_channel(dev, "rx"); ++ } else { ++ dma_cap_mask_t mask; ++ ++ dma_cap_zero(mask); ++ /* we don't care about the channel, any would work */ ++ dma_cap_set(DMA_SLAVE, mask); ++ host->dma_chan_tx = ++ dma_request_channel(mask, NULL, NULL); ++ host->dma_chan_rx = ++ dma_request_channel(mask, NULL, NULL); ++ } ++ } ++ ++ clk = devm_clk_get(dev, NULL); ++ if (IS_ERR(clk)) { ++ dev_err(dev, "could not get clk\n"); ++ ret = PTR_ERR(clk); ++ goto err; ++ } ++ ++ host->max_clk = clk_get_rate(clk); ++ ++ host->irq = platform_get_irq(pdev, 0); ++ if (host->irq <= 0) { ++ dev_err(dev, "get IRQ failed\n"); ++ ret = -EINVAL; ++ goto err; ++ } ++ ++ pr_debug(" - max_clk %lx, irq %d\n", ++ (unsigned long)host->max_clk, ++ (int)host->irq); ++ ++ if (node) ++ mmc_of_parse(mmc); ++ else ++ mmc->caps |= MMC_CAP_4_BIT_DATA; ++ ++ ret = bcm2835_sdhost_add_host(host); ++ if (ret) ++ goto err; ++ ++ platform_set_drvdata(pdev, host); ++ ++ pr_debug("bcm2835_sdhost_probe -> OK\n"); ++ ++ return 0; ++ ++err: ++ pr_debug("bcm2835_sdhost_probe -> err %d\n", ret); ++ mmc_free_host(mmc); ++ ++ return ret; ++} ++ ++static int bcm2835_sdhost_remove(struct platform_device *pdev) ++{ ++ struct bcm2835_host *host = platform_get_drvdata(pdev); ++ ++ pr_debug("bcm2835_sdhost_remove\n"); ++ ++ mmc_remove_host(host->mmc); ++ ++ bcm2835_sdhost_set_power(host, false); ++ ++ free_irq(host->irq, host); ++ ++ del_timer_sync(&host->timer); ++ ++ tasklet_kill(&host->finish_tasklet); ++ ++ mmc_free_host(host->mmc); ++ platform_set_drvdata(pdev, NULL); ++ ++ pr_debug("bcm2835_sdhost_remove - OK\n"); ++ return 0; ++} ++ ++ ++static const struct of_device_id bcm2835_sdhost_match[] = { ++ { .compatible = "brcm,bcm2835-sdhost" }, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, bcm2835_sdhost_match); ++ ++ ++ ++static struct platform_driver bcm2835_sdhost_driver = { ++ .probe = bcm2835_sdhost_probe, ++ .remove = bcm2835_sdhost_remove, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = bcm2835_sdhost_match, ++ }, ++}; ++module_platform_driver(bcm2835_sdhost_driver); ++ ++MODULE_ALIAS("platform:sdhost-bcm2835"); ++MODULE_DESCRIPTION("BCM2835 SDHost driver"); ++MODULE_LICENSE("GPL v2"); ++MODULE_AUTHOR("Phil Elwell"); |