diff options
Diffstat (limited to 'target/linux/rb1xx-2.6/files/drivers/mtd/nand/rbmipsnand.c')
| -rw-r--r-- | target/linux/rb1xx-2.6/files/drivers/mtd/nand/rbmipsnand.c | 196 |
1 files changed, 196 insertions, 0 deletions
diff --git a/target/linux/rb1xx-2.6/files/drivers/mtd/nand/rbmipsnand.c b/target/linux/rb1xx-2.6/files/drivers/mtd/nand/rbmipsnand.c new file mode 100644 index 0000000000..9d6588acf6 --- /dev/null +++ b/target/linux/rb1xx-2.6/files/drivers/mtd/nand/rbmipsnand.c @@ -0,0 +1,196 @@ +#include <linux/init.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/delay.h> +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/bootinfo.h> +#ifdef CONFIG_MIPS_ADM5120 +#include <asm/mach-adm5120/adm5120_defs.h> +#endif + +#define IDT434_REG_BASE ((volatile void *) KSEG1ADDR(0x18000000)) + +#define GPIOF 0x050000 +#define GPIOC 0x050004 +#define GPIOD 0x050008 + +#define GPIO_RDY (1 << 0x08) +#define GPIO_WPX (1 << 0x09) +#define GPIO_ALE (1 << 0x0a) +#define GPIO_CLE (1 << 0x0b) + +#define DEV2BASE 0x010020 + +#define LO_WPX (1 << 0) +#define LO_ALE (1 << 1) +#define LO_CLE (1 << 2) +#define LO_CEX (1 << 3) +#define LO_FOFF (1 << 5) +#define LO_SPICS (1 << 6) +#define LO_ULED (1 << 7) + +#define MEM32(x) *((volatile unsigned *) (x)) + + +/* RouterBoard RB1xx specific definitions */ +#define SMEM1(x) (*((volatile unsigned char *) (KSEG1ADDR(ADM5120_SRAM1_BASE) + x))) + +#define NAND_RW_REG 0x0 //data register +#define NAND_SET_CEn 0x1 //CE# low +#define NAND_CLR_CEn 0x2 //CE# high +#define NAND_CLR_CLE 0x3 //CLE low +#define NAND_SET_CLE 0x4 //CLE high +#define NAND_CLR_ALE 0x5 //ALE low +#define NAND_SET_ALE 0x6 //ALE high +#define NAND_SET_SPn 0x7 //SP# low (use spare area) +#define NAND_CLR_SPn 0x8 //SP# high (do not use spare area) +#define NAND_SET_WPn 0x9 //WP# low +#define NAND_CLR_WPn 0xA //WP# high +#define NAND_STS_REG 0xB //Status register + +static void __iomem *p_nand; + +#ifdef CONFIG_MIKROTIK_RB500 +extern void changeLatchU5(unsigned char orMask, unsigned char nandMask); + +static int rb500_dev_ready(struct mtd_info *mtd) +{ + return MEM32(IDT434_REG_BASE + GPIOD) & GPIO_RDY; +} + +/* + * hardware specific access to control-lines + * + * ctrl: + * NAND_CLE: bit 2 -> bit 3 + * NAND_ALE: bit 3 -> bit 2 + */ +static void rbmips_hwcontrol500(struct mtd_info *mtd, int cmd, + unsigned int ctrl) +{ + struct nand_chip *chip = mtd->priv; + unsigned char orbits, nandbits; + + if (ctrl & NAND_CTRL_CHANGE) { + + orbits = (ctrl & NAND_CLE) << 1; + orbits |= (ctrl & NAND_ALE) >> 1; + + nandbits = (~ctrl & NAND_CLE) << 1; + nandbits |= (~ctrl & NAND_ALE) >> 1; + + changeLatchU5(orbits, nandbits); + } + if (cmd != NAND_CMD_NONE) + writeb(cmd, chip->IO_ADDR_W); + +} +#endif + +#ifdef CONFIG_MIPS_ADM5120 +static int rb100_dev_ready(struct mtd_info *mtd) +{ + return SMEM1(NAND_STS_REG) & 0x80; /* found out by experiment */ +} + +static void rbmips_hwcontrol100(struct mtd_info *mtd, int cmd, unsigned int ctrl) +{ + struct nand_chip *chip = mtd->priv; + + if (ctrl & NAND_CTRL_CHANGE) + SMEM1(ctrl) = 0x01; + if (cmd != NAND_CMD_NONE) + writeb(cmd, chip->IO_ADDR_W); +} +#endif + + +static struct mtd_partition partition_info[] = { + { + name:"RouterBoard NAND Boot", + offset:0, + size:4 * 1024 * 1024}, + { + name:"RouterBoard NAND Main", + offset:MTDPART_OFS_NXTBLK, + size:MTDPART_SIZ_FULL} +}; + +static struct mtd_info rmtd; +static struct nand_chip rnand; + +static unsigned init_ok = 0; + +unsigned get_rbnand_block_size(void) +{ + if (init_ok) + return rmtd.writesize; + else + return 0; +} + +EXPORT_SYMBOL(get_rbnand_block_size); + +int __init rbmips_init(void) +{ + memset(&rmtd, 0, sizeof(rmtd)); + memset(&rnand, 0, sizeof(rnand)); + +#ifdef CONFIG_MIKROTIK_RB500 + printk("RB500 nand\n"); + changeLatchU5(LO_WPX | LO_FOFF | LO_CEX, + LO_ULED | LO_ALE | LO_CLE); + rnand.cmd_ctrl = rbmips_hwcontrol500; + + rnand.dev_ready = rb500_dev_ready; + rnand.IO_ADDR_W = (unsigned char *) + KSEG1ADDR(MEM32(IDT434_REG_BASE + DEV2BASE)); + rnand.IO_ADDR_R = rnand.IO_ADDR_W; +#endif + +#ifdef CONFIG_MIPS_ADM5120 + printk("RB100 nand\n"); + /* enable NAND flash */ + MEM32(0xB2000064) = 0x100; + /* boot done */ + MEM32(0xB2000008) = 0x1; + SMEM1(NAND_SET_SPn) = 0x01; + SMEM1(NAND_CLR_WPn) = 0x01; + rnand.IO_ADDR_R = (unsigned char *)KSEG1ADDR(ADM5120_SRAM1_BASE); + rnand.IO_ADDR_W = rnand.IO_ADDR_R; + rnand.cmd_ctrl = rbmips_hwcontrol100; + rnand.dev_ready = rb100_dev_ready; +#endif + p_nand = (void __iomem *) ioremap((void *) 0x18a20000, 0x1000); + if (!p_nand) { + printk("RBnand Unable ioremap buffer"); + return -ENXIO; + } + rnand.ecc.mode = NAND_ECC_SOFT; + rnand.chip_delay = 25; + rnand.options |= NAND_NO_AUTOINCR; + rmtd.priv = &rnand; + +#ifdef CONFIG_MIKROTIK_RB500 + int *b; + + b = (int *) KSEG1ADDR(0x18010020); + printk("dev2base 0x%08x mask 0x%08x c 0x%08x tc 0x%08x\n", b[0], + b[1], b[2], b[3]); +#endif + + if (nand_scan(&rmtd, 1) && nand_scan(&rmtd, 1) + && nand_scan(&rmtd, 1) && nand_scan(&rmtd, 1)) { + printk("RBxxx nand device not found"); + iounmap((void *) p_nand); + return -ENXIO; + } + + add_mtd_partitions(&rmtd, partition_info, 2); + init_ok = 1; + return 0; +} + +module_init(rbmips_init); |