#include "mitosis.h" void uart_init(void) { SERIAL_UART_INIT(); } void led_init(void) { DDRD |= (1<<1); PORTD |= (1<<1); DDRF |= (1<<4) | (1<<5); PORTF |= (1<<4) | (1<<5); } void matrix_init_kb(void) { // put your keyboard start-up code here // runs once when the firmware starts up matrix_init_user(); uart_init(); led_init(); } void matrix_scan_kb(void) { // put your looping keyboard code here // runs every cycle (a lot) matrix_scan_user(); } void led_set_kb(uint8_t usb_led) { } #ifdef ONEHAND_ENABLE __attribute__ ((weak)) const keypos_t hand_swap_config[MATRIX_ROWS][MATRIX_COLS] = { {{9, 0}, {8, 0}, {7, 0}, {6, 0}, {5, 0}, {4, 0}, {3, 0}, {2, 0}, {1, 0}, {0, 0}}, {{9, 1}, {8, 1}, {7, 1}, {6, 1}, {5, 1}, {4, 1}, {3, 1}, {2, 1}, {1, 1}, {0, 1}}, {{9, 2}, {8, 2}, {7, 2}, {6, 2}, {5, 2}, {4, 2}, {3, 2}, {2, 2}, {1, 2}, {0, 2}}, {{9, 3}, {8, 3}, {7, 3}, {6, 3}, {5, 3}, {4, 3}, {3, 3}, {2, 3}, {1, 3}, {0, 3}}, {{9, 4}, {8, 4}, {7, 4}, {6, 4}, {5, 4}, {4, 4}, {3, 4}, {2, 4}, {1, 4}, {0, 4}}, }; #endif 'form'>
openwrt master 187ad058James
aboutsummaryrefslogtreecommitdiffstats
path: root/target/image/rb532/Makefile
blob: bba89522ac8c2aab699fbde44c3c9610250cf8f4 (plain) 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51

include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk

LOADADDR = 0x81000000		# RAM start + 16M 
KERNEL_ENTRY = 0x80101000
RAMSIZE = 0x00100000		# 1MB
IMAGE_COPY = 1

LOADER_MAKEOPTS= \
		KDIR=$(KDIR) \
		LOADADDR=$(LOADADDR) \
		KERNEL_ENTRY=$(KERNEL_ENTRY) \
		RAMSIZE=$(RAMSIZE) \
		IMAGE_COPY=$(IMAGE_COPY)

define Build/Clean
	$(MAKE) -C ../generic/lzma-loader $(LOADER_MAKEOPTS) clean
endef

define Image/Prepare
	cat $(KDIR)/vmlinux | $(STAGING_DIR)/bin/lzma e -si -so -eos -lc1 -lp2 -pb2 > $(KDIR)/vmlinux.lzma
	$(MAKE) -C ../generic/lzma-loader $(LOADER_MAKEOPTS) clean compile
endef

define Image/BuildKernel
	$(CP) $(KDIR)/loader.elf $(BIN_DIR)/openwrt-$(BOARD)-$(KERNEL)-vmlinux
endef

PARTITION1=\x80\x01\x01\x00\x27\x01\x20\x7b\x20\x00\x00\x00\xe0\x1e\x00\x00# 4 MB  (kernel part)
PARTITION2=\x00\x00\x01\x7c\x83\x01\xa0\x64\x00\x1f\x00\x00\x40\x7a\x00\x00# 16 MB (rootfs part)

define Image/Build/jffs2-128k
	( \
		echo -ne OWRT | dd bs=$$$$((0x1be)) conv=sync; \
		( \
			echo -ne '$(strip $(PARTITION1))'; \
			echo -ne '$(strip $(PARTITION2))'; \
		) | dd bs=$$$$((0x40)) conv=sync; \
		echo -ne '\x55\xaa'; \
		dd if=/dev/zero bs=$$$$((0x3e00)) conv=sync count=1; \
		dd if=$(KDIR)/loader.elf bs=$$$$((0x3dc000)) conv=sync; \
		cat $(KDIR)/root.$(1); \
		echo -ne '\xde\xad\xc0\xde'; \
	) > $(BIN_DIR)/openwrt-$(BOARD)-$(KERNEL)-$(1).bin
endef

define Image/Build
	$(call Image/Build/$(1),$(1))
endef

$(eval $(call BuildImage))
generated by cgit v1.2.3 (git 2.25.1) at 2025-03-27 22:51:13 +0000