aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorSven Eckelmann <sven@narfation.org>2020-11-23 13:41:34 +0100
committerHauke Mehrtens <hauke@hauke-m.de>2022-01-09 21:12:28 +0100
commit72ef5945508193228544bcd7fcfe81b32e8dc042 (patch)
treec986c4072faadd072a28d2a2cb48acc93dd240ac
parent000825d7925f4f6a2900a2b13eb4245df0e6521b (diff)
downloadupstream-72ef5945508193228544bcd7fcfe81b32e8dc042.tar.gz
upstream-72ef5945508193228544bcd7fcfe81b32e8dc042.tar.bz2
upstream-72ef5945508193228544bcd7fcfe81b32e8dc042.zip
ath79: Add support for OpenMesh OM5P-AN
Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 1T1R 2.4 GHz Wi-Fi * 2T2R 5 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + 10/100 Mbps Ethernet + builtin switch port 1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
-rw-r--r--package/boot/uboot-envtools/files/ath791
-rw-r--r--target/linux/ath79/dts/ar9344_openmesh_om5p-an.dts230
-rw-r--r--target/linux/ath79/generic/base-files/etc/board.d/01_leds4
-rw-r--r--target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom3
-rw-r--r--target/linux/ath79/generic/base-files/lib/upgrade/platform.sh3
-rw-r--r--target/linux/ath79/image/generic.mk9
6 files changed, 248 insertions, 2 deletions
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 00339dcbcc..2ad15a7a40 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -57,6 +57,7 @@ openmesh,mr900-v2|\
openmesh,mr1750-v1|\
openmesh,mr1750-v2|\
openmesh,om5p|\
+openmesh,om5p-an|\
openmesh,om5p-ac-v2|\
samsung,wam250|\
ubnt,nanostation-m|\
diff --git a/target/linux/ath79/dts/ar9344_openmesh_om5p-an.dts b/target/linux/ath79/dts/ar9344_openmesh_om5p-an.dts
new file mode 100644
index 0000000000..e15e296f82
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_openmesh_om5p-an.dts
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9344.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "openmesh,om5p-an", "qca,ar9344";
+ model = "OpenMesh OM5P-AN";
+
+ chosen {
+ /delete-property/ bootargs;
+ };
+
+ aliases {
+ led-boot = &led_power_blue;
+ led-failsafe = &led_power_blue;
+ led-running = &led_power_blue;
+ led-upgrade = &led_power_blue;
+ label-mac-device = &eth0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_lan_wan_blue_pin>;
+
+ led_power_blue: power_blue {
+ label = "blue:power";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wan_blue {
+ label = "blue:wan";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ lan_blue {
+ label = "blue:lan";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi_green {
+ label = "green:wifi";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wifi_yellow {
+ label = "yellow:wifi";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi_red {
+ label = "red:wifi";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ i2c {
+ compatible = "i2c-gpio";
+ gpios = <&gpio 21 GPIO_ACTIVE_HIGH /* sda */
+ &gpio 20 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,sda-open-drain;
+
+ tmp423a@4c {
+ compatible = "ti,tmp423";
+ reg = <0x4c>;
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
+ hw_margin_ms = <60000>;
+ always-running;
+ };
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&pinmux {
+ led_lan_wan_blue_pin: pinmux_lan_wan_blue_pin {
+ pinctrl-single,bits = <0xc 0x0 0xffff0000>;
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ /* partitions are passed via bootloader */
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition@50000 {
+ label = "custom";
+ reg = <0x050000 0x060000>;
+ read-only;
+ };
+
+ partition@b0000 {
+ label = "inactive";
+ reg = <0x0b0000 0x7a0000>;
+ };
+
+ partition@850000 {
+ label = "inactive2";
+ reg = <0x850000 0x7a0000>;
+ };
+
+ art: partition@ff0000 {
+ label = "ART";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <0x80>;
+
+ phy7: ethernet-phy@7 {
+ reg = <7>;
+ eee-broken-100tx;
+ eee-broken-1000t;
+ };
+};
+
+&eth0 {
+ status = "okay";
+
+ pll-data = <0x02000000 0x00000101 0x00001313>;
+
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy7>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-gmac0 = <1>;
+ rxd-delay = <2>;
+ rxdv-delay = <2>;
+ switch-phy-swap = <1>;
+ };
+};
+
+&eth1 {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <1>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <2>;
+};
+
+&pcie {
+ status = "okay";
+
+ wifi@0,0 {
+ compatible = "pci168c,0030";
+ reg = <0x0000 0 0 0 0>;
+ qca,no-eeprom;
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <16>;
+ };
+};
+
+&art {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_0: macaddr@0 {
+ reg = <0x0 0x6>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 7b27dd8910..14b38b4e66 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -271,6 +271,10 @@ openmesh,om2p-hs-v4)
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0"
ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02"
;;
+openmesh,om5p-an)
+ ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
+ ucidef_set_led_switch "wan" "WAN" "blue:wan" "switch0" "0x02"
+ ;;
pcs,cr3000)
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
ucidef_set_led_switch "lan1" "LAN1" "blue:lan1" "switch0" "0x04"
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 89a6adf5a6..10421c2e28 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -127,7 +127,8 @@ case "$FIRMWARE" in
caldata_extract "art" 0x1000 0x1000
;;
openmesh,mr600-v1|\
- openmesh,mr600-v2)
+ openmesh,mr600-v2|\
+ openmesh,om5p-an)
caldata_extract "ART" 0x5000 0x440
;;
wd,mynet-n600|\
diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
index 20041e4c95..b7e2930129 100644
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
@@ -80,7 +80,8 @@ platform_do_upgrade() {
openmesh,om2p-hs-v3|\
openmesh,om2p-hs-v4|\
openmesh,om2p-lc|\
- openmesh,om5p)
+ openmesh,om5p|\
+ openmesh,om5p-an)
PART_NAME="inactive"
platform_do_upgrade_openmesh "$1"
;;
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 5e211a33a4..e17b498d88 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1924,6 +1924,15 @@ define Device/openmesh_om5p-ac-v2
endef
TARGET_DEVICES += openmesh_om5p-ac-v2
+define Device/openmesh_om5p-an
+ $(Device/openmesh_common_64k)
+ SOC := ar9344
+ DEVICE_MODEL := OM5P-AN
+ OPENMESH_CE_TYPE := OM5P
+ SUPPORTED_DEVICES += om5p-an
+endef
+TARGET_DEVICES += openmesh_om5p-an
+
define Device/pcs_cap324
SOC := ar9344
DEVICE_VENDOR := PowerCloud Systems