aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorStas Fiduchi <fiduchi@protonmail.com>2021-06-12 11:35:27 +0300
committerAdrian Schmutzler <freifunk@adrianschmutzler.de>2021-07-10 20:01:29 +0200
commitb8168f4716ad64863db8a6a2aba24bbff4664ffe (patch)
treef16c1b4f21a785afed296bf1c7030e339bbcff28
parentcce8d16bf18909e1634c0aeac05e40a7be96a519 (diff)
downloadupstream-b8168f4716ad64863db8a6a2aba24bbff4664ffe.tar.gz
upstream-b8168f4716ad64863db8a6a2aba24bbff4664ffe.tar.bz2
upstream-b8168f4716ad64863db8a6a2aba24bbff4664ffe.zip
ramips: add support for D-Link DIR-853-R1
This PR adds support for router D-Link DIR-853-R1 Specifications: SoC: MT7621AT RAM: 128MB Flash: 16MB SPI WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC (This mode allows this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the same time) LAN: 5x1000M LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue USB Blue Buttons Reset,WPS, Wifi MAC addresses: |Interface | MAC | Factory |Comment |------------|-----------------|-------------|---------------- |WAN sticker |C4:XX:XX:6E:XX:2A| |Sticker |LAN |C4:XX:XX:6E:XX:2B| | |Wifi (5g) |C4:XX:XX:6E:XX:2C|0x4 | |Wifi (2.4g) |C6:XX:XX:7E:XX:2C| | | | | | | |C4:XX:XX:6E:XX:2E|0x8004 0xe000| | |C4:XX:XX:6E:XX:2F|0xe006 | The increment of the 4th byte for the 2.4g address appears to vary. Reported cases: 5g 2.4g increment C4:XX:XX:6E:XX:2C C6:XX:XX:7E:XX:2C 0x10 f4:XX:XX:16:XX:32 f6:XX:XX:36:XX:32 0x20 F4:XX:XX:A6:XX:E3 F6:XX:XX:B6:XX:E3 0x10 Since increment is inconsistent and there is no obvious pattern in swapping bytes, and the 2.4g address has local bit set anyway, it seems safer to use the LAN address with flipped byte here in order to prevent collisions between OpenWrt devices and OEM devices for this interface. This way we at least use an address as base that is definitely owned by the device at hand. Flashing instruction: The Dlink "Emergency Room" Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.101 / 255.255.255.0. Then, power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the internet LED stops flashing Call the recovery page or tftp for the device at http://192.168.0.1 Use the provided emergency web GUI to upload and flash a new firmware to the device. Signed-off-by: Stas Fiduchi <fiduchi@protonmail.com> [commit title/message improvements, use correct label MAC address, calculate MAC addresses based on 0x4, minor DTS style fixes, add uart2 to state_default, remove factory image, add 2.4g MAC address, use partition DTSI, add macaddr comment in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
-rw-r--r--target/linux/ramips/dts/mt7621_dlink_dir-853-r1.dts144
-rw-r--r--target/linux/ramips/image/mt7621.mk8
-rw-r--r--target/linux/ramips/mt7621/base-files/etc/board.d/01_leds3
-rw-r--r--target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac6
4 files changed, 161 insertions, 0 deletions
diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-853-r1.dts b/target/linux/ramips/dts/mt7621_dlink_dir-853-r1.dts
new file mode 100644
index 0000000000..09e46b011e
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_dlink_dir-853-r1.dts
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include "mt7621_dlink_flash-16m-r1.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "dlink,dir-853-r1", "mediatek,mt7621-soc";
+ model = "D-Link DIR-853 R1";
+
+ aliases {
+ label-mac-device = &wan;
+ led-boot = &led_power_orange;
+ led-failsafe = &led_power_blue;
+ led-running = &led_power_blue;
+ led-upgrade = &led_net_orange;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power_orange: power_orange {
+ label = "orange:power";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_blue: power_blue {
+ label = "blue:power";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led_net_orange: net_orange {
+ label = "orange:net";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ net_blue {
+ label = "blue:net";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ usb_blue {
+ label = "blue:usb";
+ gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&xhci_ehci_port1>;
+ linux,default-trigger = "usbport";
+ };
+
+ wlan2g {
+ label = "blue:wlan2g";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0radio";
+ };
+
+ wlan5g {
+ label = "blue:wlan5g";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1radio";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ wifi {
+ label = "wifi";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi@0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0>;
+ /* 5 GHz (phy1) does not take the address from calibration data,
+ but setting it manually here works */
+ mtd-mac-address = <&factory 0x4>;
+ };
+};
+
+&gmac0 {
+ mtd-mac-address = <&factory 0x4>;
+ mtd-mac-address-increment = <(-1)>;
+};
+
+&switch0 {
+ ports {
+ port@0 {
+ status = "okay";
+ label = "lan4";
+ };
+
+ port@1 {
+ status = "okay";
+ label = "lan3";
+ };
+
+ port@2 {
+ status = "okay";
+ label = "lan2";
+ };
+
+ port@3 {
+ status = "okay";
+ label = "lan1";
+ };
+
+ wan: port@4 {
+ status = "okay";
+ label = "wan";
+ mtd-mac-address = <&factory 0x4>;
+ mtd-mac-address-increment = <(-2)>;
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "i2c", "uart3", "uart2", "jtag", "wdt";
+ function = "gpio";
+ };
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index a11fa21fb4..63d28530b6 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -342,6 +342,14 @@ define Device/dlink_dir-2660-a1
endef
TARGET_DEVICES += dlink_dir-2660-a1
+define Device/dlink_dir-853-r1
+ $(Device/dlink_dir-8xx-r1)
+ DEVICE_MODEL := DIR-853
+ DEVICE_VARIANT := R1
+ DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport
+endef
+TARGET_DEVICES += dlink_dir-853-r1
+
define Device/dlink_dir-860l-b1
$(Device/dsa-migration)
$(Device/seama)
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
index c04dae4f0d..cb889de208 100644
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
@@ -23,6 +23,9 @@ d-team,newifi-d2)
ucidef_set_led_netdev "wlan2g" "WiFi 2.4GHz" "blue:wlan2g" "wlan0"
ucidef_set_led_netdev "wlan5g" "WiFi 5GHz" "blue:wlan5g" "wlan1"
;;
+dlink,dir-853-r1)
+ ucidef_set_led_netdev "internet" "internet" "blue:net" "wan"
+ ;;
d-team,pbr-m1|\
gehua,ghl-r-001|\
jcg,y2|\
diff --git a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
index bd0f0254c6..24d73b039d 100644
--- a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
+++ b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
@@ -10,6 +10,12 @@ PHYNBR=${DEVPATH##*/phy}
board=$(board_name)
case "$board" in
+ dlink,dir-853-r1)
+ [ "$PHYNBR" = "0" ] && \
+ base_mac=$(mtd_get_mac_binary factory 0x4)
+ base_mac=$(macaddr_add "$base_mac" -1)
+ macaddr_setbit_la "$base_mac" > /sys${DEVPATH}/macaddress
+ ;;
glinet,gl-mt1300)
[ "$PHYNBR" = "1" ] && \
macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1 > /sys${DEVPATH}/macaddress