diff options
author | Chris Blake <chrisrblake93@gmail.com> | 2018-03-10 10:59:18 +0100 |
---|---|---|
committer | Mathias Kresin <dev@kresin.me> | 2018-03-14 19:04:52 +0100 |
commit | 4943afd7818f56053231a5a7ae90e55da44f1f08 (patch) | |
tree | 3f54b0e72647dc6ef0a595e2e377aeb3ae58a9a9 /package/firmware/ipq-wifi/board-avm_fritzbox-4040.bin | |
parent | 4f4fc993db4cd074fb2b51586dadd10e882604ec (diff) | |
download | upstream-4943afd7818f56053231a5a7ae90e55da44f1f08.tar.gz upstream-4943afd7818f56053231a5a7ae90e55da44f1f08.tar.bz2 upstream-4943afd7818f56053231a5a7ae90e55da44f1f08.zip |
ipq40xx: add Cisco Meraki MR33 Support
This patch adds support for Cisco Meraki MR33
hardware highlights:
SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
1 x Orange LED Fault Indicator (shared with LP5562)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
AT24C64 8KiB EEPROM
Kensington Lock
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
1x4 0.1" header with half-height/low profile pins.
The pinout is: VCC (little white arrow), RX, TX, GND.
Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>
Add images to do an installation via bootloader:
0. open up the MR33 and connect the serial console.
1. start the 2nd stage bootloader transfer from client pc:
# ubootwrite.py --write=mr33-uboot.bin
(The ubootwrite tool will interrupt the boot-process and hence
it needs to listen for cues. If the connection is bad (due to
the low-profile pins), the tool can fail multiple times and in
weird ways. If you are not sure, just use a terminal program
and see what the device is doing there.
2. power on the MR33 (with ethernet + serial cables attached)
Warning: Make sure you do this in a private LAN that has
no connection to the internet.
- let it upload the u-boot this can take 250-300 seconds -
3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
(the u-boot is listening on 192.168.1.1)
# tftp 192.168.1.1
binary
put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin
4. wait for it to reboot
5. connect to your MR33 via ssh on 192.168.1.1
For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)
Thanks to Jerome C. for sending an MR33 to Chris.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'package/firmware/ipq-wifi/board-avm_fritzbox-4040.bin')
0 files changed, 0 insertions, 0 deletions