aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/base-files/etc
diff options
context:
space:
mode:
authorChristian Mauderer <oss@c-mauderer.de>2019-03-15 21:02:54 +0100
committerPetr Štetiar <ynezz@true.cz>2019-04-08 18:37:04 +0200
commit8a4dc6f48c0a4503b655195846ae1bff9a691a40 (patch)
tree6311f19ecd01cec2d644737eaaf57ffa1d9d315f /target/linux/ath79/base-files/etc
parentde2f888024ac58c6137959ea91f65cb6ad098df3 (diff)
downloadupstream-8a4dc6f48c0a4503b655195846ae1bff9a691a40.tar.gz
upstream-8a4dc6f48c0a4503b655195846ae1bff9a691a40.tar.bz2
upstream-8a4dc6f48c0a4503b655195846ae1bff9a691a40.zip
ath79: add support for Ubiquiti airCube ISP
The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal 2x2 MIMO antennas. It can be supplied via a USB connector or via PoE. There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an optional PoE passthrough from the first LAN port to the WAN port. SoC: Qualcomm / Atheros QCA9533-BL3A RAM: 64 MB DDR2 Flash: 16 MB SPI NOR Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN) LEDS: 1x via a SPI controller (not yet supported) Buttons: 1x Reset Serial: 1x (only RX and TX); 115200 baud, 8N1 Missing points: - LED not yet supported - Factory upgrade via web IF or TFTP recovery not yet supported (Needs RSA signed images, for details see PR#1958) The serial port is on a four pin connextor labeled J1 and located between Ethernet and USB connector. The pinout is: 1. 3V3 (out) 2. Rx (in) 3. Tx (out) 4. GND Upgrading via serial port / U-Boot: - Connect the serial port via a level converter - Power the system and stop U-Boot with pressing any key when `Hit any key to stop autoboot` is displayed. Note: Pressing space multiple times untill U-Boot reaches that location works well. - Connect a PC with the IP 192.168.1.100 (or some other in that net) running a TFTP-Server to one of the LAN ports. Copy the sysupgrade image to the server. - Set the U-Boot server IP with setenv serverip 192.168.1.100 - Load the flash image to RAM with tftpboot 0x81000000 sysupgrade.bin - Erase the flash with erase 0x9f050000 0x9ffaffff - Write the new flash content with cp 0x81000000 0x9f050000 ${filesize} - Reset the device with reset Signed-off-by: Christian Mauderer <oss@c-mauderer.de> [removed full stop in subject and added lockdown note to commit message] Signed-off-by: Petr Štetiar <ynezz@true.cz>
Diffstat (limited to 'target/linux/ath79/base-files/etc')
-rwxr-xr-xtarget/linux/ath79/base-files/etc/board.d/02_network5
-rwxr-xr-xtarget/linux/ath79/base-files/etc/board.d/03_gpio_switches3
2 files changed, 8 insertions, 0 deletions
diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index e399210b2b..4651669d31 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -233,6 +233,11 @@ ath79_setup_interfaces()
tplink,tl-wr941-v2)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;
+ ubnt,acb-isp)
+ ucidef_set_interface_wan "eth0"
+ ucidef_add_switch "switch0" \
+ "0@eth1" "2:lan:1" "3:lan:3" "4:lan:2"
+ ;;
ubnt,routerstation-pro)
ucidef_set_interface_wan "eth0"
ucidef_add_switch "switch0" \
diff --git a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches
index c852b77d79..6a51a79790 100755
--- a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches
@@ -26,6 +26,9 @@ librerouter,librerouter-v1)
ubnt,nanostation-ac)
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "3"
;;
+ubnt,acb-isp)
+ ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "11"
+ ;;
esac
board_config_flush