diff options
author | David Bauer <mail@david-bauer.net> | 2020-04-14 03:58:37 +0200 |
---|---|---|
committer | David Bauer <mail@david-bauer.net> | 2020-04-19 16:45:40 +0200 |
commit | 8d9c1087e4d07d625a9fef61d5dce71d850732ae (patch) | |
tree | 78f125291c0085a570dd288decce08bd2927a7f7 /target/linux/ath79/dts/qca9556_avm_fritz1750e.dts | |
parent | 45e2b7763f2a846bf1a40f5fa79b4cfe4678557a (diff) | |
download | upstream-8d9c1087e4d07d625a9fef61d5dce71d850732ae.tar.gz upstream-8d9c1087e4d07d625a9fef61d5dce71d850732ae.tar.bz2 upstream-8d9c1087e4d07d625a9fef61d5dce71d850732ae.zip |
ath79: add support for AVM FRITZ!WLAN Repeater 450E
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.
Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'target/linux/ath79/dts/qca9556_avm_fritz1750e.dts')
-rw-r--r-- | target/linux/ath79/dts/qca9556_avm_fritz1750e.dts | 89 |
1 files changed, 3 insertions, 86 deletions
diff --git a/target/linux/ath79/dts/qca9556_avm_fritz1750e.dts b/target/linux/ath79/dts/qca9556_avm_fritz1750e.dts index f50af5b228..25d3ae8da4 100644 --- a/target/linux/ath79/dts/qca9556_avm_fritz1750e.dts +++ b/target/linux/ath79/dts/qca9556_avm_fritz1750e.dts @@ -1,19 +1,13 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT -/dts-v1/; #include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> -#include "qca9557.dtsi" +#include "qca9556_avm_fritz-repeater.dtsi" / { compatible = "avm,fritz1750e", "qca,qca9557"; model = "AVM FRITZ!WLAN Repeater 1750E"; - chosen { - bootargs = "console=ttyS0,115200n8"; - }; - aliases { led-boot = &led_power; led-failsafe = &led_power; @@ -91,65 +85,14 @@ gpios = <&spi_gpio 4 GPIO_ACTIVE_HIGH>; }; }; - - keys { - compatible = "gpio-keys"; - - wps { - label = "wps"; - linux,code = <KEY_WPS_BUTTON>; - gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; - }; - }; }; &pcie0 { status = "okay"; }; -&uart { - status = "okay"; -}; - -&spi { - status = "okay"; - num-cs = <1>; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <25000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "urlader"; - reg = <0x0 0x20000>; - read-only; - }; - - partition@20000 { - compatible = "avm,eva-firmware"; - label = "firmware"; - reg = <0x20000 0xee0000>; - }; - - partition@f00000 { - label = "tffs (1)"; - reg = <0xf00000 0x80000>; - read-only; - }; - - partition@f80000 { - label = "tffs (2)"; - reg = <0xf80000 0x80000>; - read-only; - }; - }; - }; +&phy0 { + reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>; }; &gpio { @@ -167,29 +110,3 @@ line-name = "PCIE Bus reset"; }; }; - -&wmac { - status = "okay"; - qca,no-eeprom; -}; - -ð1 { - status = "okay"; - - phy-handle = <&phy0>; - pll-data = <0x3000000 0x101 0x1313>; - - gmac-config { - device = <&gmac>; - ge0-sgmii = <0>; - }; -}; - -&mdio1 { - status = "okay"; - - phy0: ethernet-phy@0 { - reg = <0>; - reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - }; -}; |