ath79: modify mtd partitions for Buffalo BHR-4GRV2

This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.

In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.

0x50000                       0xe80000        0xff0000
  +-------------------------------+--------------+
  |            rootfs             |    kernel    |
  |           (14528k)            |    (1472k)   |
  +-------------------------------+--------------+

After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.

0x50000                                       0xff0000
  +----------------------------------------------+
  |                   firmware                   |
  |                   (16000k)                   |
  +----------------------------------------------+

However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".

This commit requires new flash instruction instead of the old one.

Flash instruction using initramfs image:

1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
  /dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
  fw_setenv ipaddr 192.168.12.1
  fw_setenv serverip 192.168.12.10
  fw_setenv ethaddr 00:aa:bb:cc:dd:ee
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing

And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>

1 files changed, 150 insertions, 0 deletions

diff --git a/target/linux/ath79/dts/qca9557_buffalo_bhr-4grv2.dts b/target/linux/ath79/dts/qca9557_buffalo_bhr-4grv2.dts
new file mode 100644
index 0000000000..6a3a5da6d6
--- /dev/null
+++ b/target/linux/ath79/dts/qca9557_buffalo_bhr-4grv2.dts
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9557.dtsi"
+
+/ {
+	compatible = "buffalo,bhr-4grv2", "qca,qca9557";
+	model = "Buffalo BHR-4GRV2";
+
+	aliases {
+		led-boot = &power;
+		led-failsafe = &power;
+		led-running = &power;
+		led-upgrade = &power;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		power: power {
+			label = "bhr-4grv2:green:power";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		diag {
+			label = "bhr-4grv2:orange:diag";
+			gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		vpn_orange {
+			label = "bhr-4grv2:orange:vpn";
+			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		vpn_green {
+			label = "bhr-4grv2:green:vpn";
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		reset {
+			label = "reset";
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+			debounce-interval = <60>;
+		};
+
+		eco {
+			label = "eco";
+			gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+			debounce-interval = <60>;
+		};
+	};
+};
+
+&spi {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x040000 0x010000>;
+			};
+
+			partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x050000 0xfa0000>;
+			};
+
+			art: partition@ff0000 {
+				label = "art";
+				reg = <0xff0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+
+		qca,ar8327-initvals = <
+		    0x04 0x80080080 /* PORT0 PAD MODE CTRL */
+		    0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
+		    0x7c 0x0000007e /* PORT0_STATUS */
+		    0x94 0x0000007e /* PORT6 STATUS */
+		>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	mtd-mac-address = <&art 0x0>;
+	phy-handle = <&phy0>;
+	pll-data = <0x56000000 0x00000101 0x00001616>;
+};
+
+&eth1 {
+	status = "okay";
+
+	mtd-mac-address = <&art 0x6>;
+	pll-data = <0x03000101 0x00000101 0x00001616>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&uart {
+	status = "okay";
+};