ath79: create common DTSI for ECB1200 and ECB1750

These boards are sister boards

exactly the same hardware except that ECB1200 has:
 - QCA9557
 - 2 RF circuits/antennas per band instead of 3
 - a resistor blocking UART RX line

Tested-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Michael Pratt <mcpratt@pm.me>

1 files changed, 1 insertions, 132 deletions

diff --git a/target/linux/ath79/dts/qca9558_engenius_ecb1750.dts b/target/linux/ath79/dts/qca9558_engenius_ecb1750.dts
index 159ccc1872..4ee4c8ea69 100644
--- a/target/linux/ath79/dts/qca9558_engenius_ecb1750.dts
+++ b/target/linux/ath79/dts/qca9558_engenius_ecb1750.dts
@@ -1,139 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 
-#include "qca955x.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "qca955x_engenius_ecb1xxx.dtsi"
 
 / {
 	compatible = "engenius,ecb1750", "qca,qca9558";
 	model = "EnGenius ECB1750";
-
-	aliases {
-		led-boot = &led_power_orange;
-		led-failsafe = &led_power_orange;
-		led-running = &led_power_orange;
-		led-upgrade = &led_power_orange;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led_power_orange: power_orange {
-			label = "orange:power";
-			gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
-			default-state = "on";
-		};
-
-		wlan2g {
-			label = "blue:wlan2g";
-			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "phy1tpt";
-		};
-
-		wlan5g {
-			label = "blue:wlan5g";
-			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "phy0tpt";
-		};
-
-		lan {
-			label = "blue:lan";
-			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		reset {
-			label = "reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-&pcie0 {
-	status = "okay";
-};
-
-&uart {
-	status = "okay";
-};
-
-&spi {
-	status = "okay";
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <25000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			uboot: partition@0 {
-				label = "u-boot";
-				reg = <0x000000 0x040000>;
-				read-only;
-			};
-
-			partition@40000 {
-				label = "u-boot-env";
-				reg = <0x040000 0x010000>;
-			};
-
-			partition@50000 {
-				compatible = "denx,uimage";
-				label = "firmware";
-				reg = <0x050000 0xf50000>;
-			};
-
-			partition@fa0000 {
-				label = "userconfig";
-				reg = <0xfa0000 0x050000>;
-				read-only;
-			};
-
-			art: partition@ff0000 {
-				label = "art";
-				reg = <0xff0000 0x010000>;
-				read-only;
-			};
-		};
-	};
-};
-
-&wmac {
-	status = "okay";
-
-	qca,no-eeprom;
-};
-
-&mdio0 {
-	status = "okay";
-
-	phy5: ethernet-phy@5 {
-		reg = <5>;
-		eee-broken-100tx;
-		eee-broken-1000t;
-	};
-};
-
-&eth0 {
-	status = "okay";
-
-	pll-data = <0x9a000000 0x80000101 0x80001313>;
-
-	phy-handle = <&phy5>;
-
-	gmac-config {
-		device = <&gmac>;
-		rgmii-gmac0 = <1>;
-		rxd-delay = <3>;
-		rxdv-delay = <3>;
-	};
 };