ath79: add support for TP-Link TL-WPA8630 v1

This ports the TP-Link TL-WPA8630 v1 from ar71xx to ath79.

Specifications:

SoC: QCA9563
CPU: 750 MHz
Flash/RAM: 8 / 128 MiB
Ethernet: 3x 1G ports (QCA8337 switch)
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac (ath10k)

Buttons, LEDs and network setup appear to be almost identical
to the v2 revision.

Powerline interface is connected to switch port 5 (Label LAN4).

Installation:

No "fresh" device was available for testing the factory image.

It is not known whether flashing via OEM firmware GUI is possible
or not. A discussion from 2018 [1] about that indicates a few
adjustments are necessary, but it is not clear whether those
are already implemented with the TPLINK_HEADER_VERSION = 2 or not.

Note that for the TL-WPA8630P v1, the TPLINK_HWID needs to be
changed to 0x86310001 to allow factory flashing.

[1] https://forum.openwrt.org/t/solved-tl-wpa8630p-lede-does-not-install/8161/27

Recovery:

Recovery is only possible via serial.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

1 files changed, 122 insertions, 0 deletions

diff --git a/target/linux/ath79/dts/qca9563_tplink_tl-wpa8630.dtsi b/target/linux/ath79/dts/qca9563_tplink_tl-wpa8630.dtsi
new file mode 100644
index 0000000000..68b455c66a
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_tplink_tl-wpa8630.dtsi
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	keys: keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "Reset button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		leds {
+			label = "LED control button";
+			linux,code = <BTN_0>;
+			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		pair {
+			label = "Pair button";
+			linux,code = <BTN_1>;
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "tp-link:green:power";
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "tp-link:green:lan";
+			gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+		};
+
+		wifi2g {
+			label = "tp-link:green:wifi2g";
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		wifi5g {
+			label = "tp-link:green:wifi5g";
+			gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+	};
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions: partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&uart {
+	status = "okay";
+};
+
+&mdio0 {
+	status = "okay";
+
+	phy-mask = <0>;
+
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		phy-mode = "sgmii";
+		qca,mib-poll-interval = <500>;
+
+		qca,ar8327-initvals = <
+			0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+			0x7c 0x0000007e /* PORT0_STATUS */
+		>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-handle = <&phy0>;
+	phy-mode = "sgmii";
+};
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+};