diff options
author | Roman Hampel <rhamp@arcor.de> | 2020-03-20 17:32:30 +0100 |
---|---|---|
committer | Adrian Schmutzler <freifunk@adrianschmutzler.de> | 2020-04-09 01:06:37 +0200 |
commit | cd510e775bc7c806b3ad6981221258385554b9e8 (patch) | |
tree | 15cc47f1513a932e81b8bf9d7479b85d8967e29f /target/linux/ath79/generic/base-files/etc/board.d/01_leds | |
parent | b299002877c801202c3b61d5e09865e88f506176 (diff) | |
download | upstream-cd510e775bc7c806b3ad6981221258385554b9e8.tar.gz upstream-cd510e775bc7c806b3ad6981221258385554b9e8.tar.bz2 upstream-cd510e775bc7c806b3ad6981221258385554b9e8.zip |
ath79: add support for Comfast CF-WR752AC v1
Specifications:
- Qualcomm QCA9531 + QCA9886
- dual band, antenna 2*3dBi
- Output power 50mW (17dBm)
- 1x 10/100 Mbps LAN RJ45
- 128 MB RAM / 16 MB FLASH (w25q128)
- 3 LEDs (red/green/blue)
incorporated in
"color wheel reset switch"
- UART 115200 8N1
Flashing instructions:
The U-boot bootloader contains a recovery HTTP server
to upload the firmware. Push the reset button while powering the
device on and keep it pressed for ~10 seconds. The device's LEDs will
blink several times and the recovery page will be at
http://192.168.1.1; use it to upload the sysupgrade image.
Alternatively, the original firmware is based on OpenWrt so a
sysupgrade image can be installed via the stock web GUI. Settings from
the original firmware will be saved and restored on the new one, so a
factory reset will be needed. To do so, once the new firmware is flashed,
enter into failsafe mode by pressing the reset button several times during
the boot process, until it starts flashing. Once in failsafe mode, perform
a factory reset as usual.
LED-Info:
The LEDs on the Comfast stock fw have a very proprietary behaviour,
corresponding to the user selected working mode (AP, ROUTER or REPEATER).
In the first two cases, only blue is used for status and LAN signaling. When
using the latter, blue is always off (except for sysupgrade), either red
signals bad rssi on master-link, or green good. Since the default working
mode of OpenWrt resembles that of a router/AP, the default behavior is
implemented accordingly.
MAC addresses (art partition):
location address (example) use in vendor firmware
0x0 xx:xx:xx:xx:xc:f8 -> eth0
0x6 xx:xx:xx:xx:xc:fa -> wlan5g (+2)
0x1002 xx:xx:xx:xx:xc:f9 -> not used
0x5006 xx:xx:xx:xx:xc:fb -> not used
--- xx:xx:xx:xx:xd:02 -> wlan2g (+10)
The same strange situation has already been observed and documented
for COMFAST CF-E560AC.
Signed-off-by: Roman Hampel <rhamp@arcor.de>
Co-developed-by: Joao Albuquerque <joaohccalbu@gmail.com>
Signed-off-by: Joao Albuquerque <joaohccalbu@gmail.com>
[adjust and extend commit message, rebase, minor DTS adjustments,
add correct MAC address for wmac, change RSSI LED names and behavior]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Diffstat (limited to 'target/linux/ath79/generic/base-files/etc/board.d/01_leds')
-rwxr-xr-x | target/linux/ath79/generic/base-files/etc/board.d/01_leds | 7 |
1 files changed, 4 insertions, 3 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 8e84ca25bf..b946d0c63b 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -84,6 +84,10 @@ comfast,cf-ew72) ucidef_set_led_switch "lan" "LAN" "$boardname:blue:lan" "switch0" "0x02" ucidef_set_led_netdev "wan" "WAN" "$boardname:blue:wan" "eth1" ;; +comfast,cf-wr752ac-v1|\ +engenius,ecb1750) + ucidef_set_led_netdev "lan" "LAN" "$boardname:blue:lan" "eth0" + ;; devolo,magic-2-wifi) ucidef_set_led_netdev "plcw" "dLAN" "devolo:white:dlan" "eth0.1" "rx" ;; @@ -93,9 +97,6 @@ dlink,dir-842-c3|\ dlink,dir-859-a1) ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20" ;; -engenius,ecb1750) - ucidef_set_led_netdev "lan" "LAN" "$boardname:blue:lan" "eth0" - ;; engenius,ews511ap) ucidef_set_led_netdev "lan1" "LAN1" "$boardname:blue:lan1" "eth1" ucidef_set_led_netdev "lan2" "LAN2" "$boardname:blue:lan2" "eth0" |