aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/generic/base-files
diff options
context:
space:
mode:
authorBernhard Geier <freifunk@geierb.de>2019-11-03 13:58:12 +0100
committerAdrian Schmutzler <freifunk@adrianschmutzler.de>2019-11-03 13:59:18 +0100
commit3930aab2cb067d04f5c9ebbf1af57744e19355eb (patch)
tree4f3363da89309e2e11676ef64ecc00336b06b8dc /target/linux/ath79/generic/base-files
parent66ebca7103052ba851be2261a4452787959de9c2 (diff)
downloadupstream-3930aab2cb067d04f5c9ebbf1af57744e19355eb.tar.gz
upstream-3930aab2cb067d04f5c9ebbf1af57744e19355eb.tar.bz2
upstream-3930aab2cb067d04f5c9ebbf1af57744e19355eb.zip
ath79: add support for TP-Link WBS210 v2
TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with two Ethernet ports based on Atheros AR9344 The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm instead of 12 dBm) and two antenna connectors instead of built-in antennas. Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP: 192.168.0.100 Stock device TFTP adress: 192.168.0.254 The TP-Link WBS devices use the same GPIOs as the CPE devices, except for the link4 LED. For this one, WBS devices use "2", while CPE devices use "16". (Tested on WBS210 v2) Signed-off-by: Bernhard Geier <freifunk@geierb.de> [added comment about GPIO] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Diffstat (limited to 'target/linux/ath79/generic/base-files')
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/01_leds3
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/02_network1
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches3
3 files changed, 5 insertions, 2 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 441091de32..fbb0d0ea03 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -173,7 +173,8 @@ tplink,archer-d50-v1)
;;
tplink,cpe210-v1|\
tplink,cpe220-v2|\
-tplink,cpe510-v1)
+tplink,cpe510-v1|\
+tplink,wbs210-v2)
ucidef_set_led_netdev "lan0" "LAN0" "tp-link:green:lan0" "eth1"
ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
ucidef_set_rssimon "wlan0" "200000" "1"
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index e4179b4d38..10ca213e70 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -90,6 +90,7 @@ ath79_setup_interfaces()
tplink,cpe210-v1|\
tplink,cpe220-v2|\
tplink,cpe510-v1|\
+ tplink,wbs210-v2|\
ubnt,nanostation-m|\
ubnt,routerstation)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches b/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
index d84d6cfe85..4d6277c223 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
@@ -44,7 +44,8 @@ tplink,archer-c25-v1)
;;
tplink,cpe210-v1|\
tplink,cpe220-v2|\
-tplink,cpe510-v1)
+tplink,cpe510-v1|\
+tplink,wbs210-v2)
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "20"
;;
ubnt,nanostation-ac)