diff options
| author | Piotr Dymacz <pepe2k@gmail.com> | 2020-03-21 23:20:31 +0100 |
|---|---|---|
| committer | Piotr Dymacz <pepe2k@gmail.com> | 2020-09-28 01:28:37 +0200 |
| commit | 66abd58196a8e1195f1e2cd9871b4fc194b6570b (patch) | |
| tree | d0959571e260cfdd3083fd4f8d1ba132379d270a /target/linux/ath79/generic/base-files | |
| parent | 7f96cbd2a11a382a940ecdfc75d45bad44283414 (diff) | |
| download | upstream-66abd58196a8e1195f1e2cd9871b4fc194b6570b.tar.gz upstream-66abd58196a8e1195f1e2cd9871b4fc194b6570b.tar.bz2 upstream-66abd58196a8e1195f1e2cd9871b4fc194b6570b.zip | |
ath79: add support for ALFA Network AP121FE
The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in 0c6165d21a and to ath79 in 334bbc5198).
The differences in compare to AP121F:
- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)
Other than that, specifications are the same:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Diffstat (limited to 'target/linux/ath79/generic/base-files')
| -rwxr-xr-x | target/linux/ath79/generic/base-files/etc/board.d/01_leds | 1 | ||||
| -rwxr-xr-x | target/linux/ath79/generic/base-files/etc/board.d/02_network | 4 |
2 files changed, 5 insertions, 0 deletions
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index ef7a0d4e3c..a90aaf0231 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -13,6 +13,7 @@ case "$board" in ucidef_set_led_switch "wan" "WAN" "$boardname:orange:eth1" "switch0" "0x04" ;; alfa-network,ap121f|\ +alfa-network,ap121fe|\ avm,fritz450e) ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0" ;; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 518ca6f91a..ab8e24adde 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -75,6 +75,9 @@ ath79_setup_interfaces() winchannel,wb2000) ucidef_set_interface_lan "eth0" ;; + alfa-network,ap121fe) + ucidef_set_interface_lan "eth0 usb0" + ;; avm,fritz4020|\ pcs,cr3000|\ tplink,archer-c58-v1|\ @@ -398,6 +401,7 @@ ath79_setup_macs() label_mac=$lan_mac ;; alfa-network,ap121f|\ + alfa-network,ap121fe|\ engenius,ens202ext-v1) label_mac=$(mtd_get_mac_binary art 0x1002) ;; |