aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ath79/nand/base-files
diff options
context:
space:
mode:
authorMichal Cieslakiewicz <michal.cieslakiewicz@wp.pl>2019-12-22 21:54:33 +0100
committerJohn Crispin <john@phrozen.org>2020-01-15 20:55:56 +0100
commit37a36a588a015c5f9e57c80c75670cf993955f24 (patch)
treebc6ff52e56660b9d9d20e1142737008068cd5dee /target/linux/ath79/nand/base-files
parent4e6af8b9efcfc51e217d793239487dd8af1f410e (diff)
downloadupstream-37a36a588a015c5f9e57c80c75670cf993955f24.tar.gz
upstream-37a36a588a015c5f9e57c80c75670cf993955f24.tar.bz2
upstream-37a36a588a015c5f9e57c80c75670cf993955f24.zip
ath79: add support for Netgear WNDR4300 v2
This patch introduces support for Netgear WNDR4300v2. Specification ============= * Description: Netgear WNDR4300 v2 * Loader: U-boot * SOC: Qualcomm Atheros QCA9563 (775 MHz) * RAM: 128 MiB * Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND - NOR: U-boot binary: 256 KiB - NOR: U-boot environment: 64 KiB - NOR: ART Backup: 64 KiB - NOR: Config: 64 KiB - NOR: Traffic Meter: 64 KiB - NOR: POT: 64 KiB - NOR: Reserved: 1408 KiB - NOR: ART: 64 KiB - NAND: Firmware: 25600 KiB (see notes for OpenWrt) - NAND: Language: 2048 KiB - NAND: mtdoops Crash Dump: 128 KiB - NAND: Reserved: 103296 KiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Important Notes =============== 0. NOR Flash (2 MiB) is not touched by OpenWrt installation. 1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows: all space is split between 4 MiB kernel and 124 MiB UBI areas; vendor partitions (language and mtdoops) are removed; kernel space size can be further expanded if needed; maximum image size is set to 25600k for compatibility reasons and can also be increased. 2. CPU clock is 775 MHz, not 750 MHz. 3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI device ID 0xabcd. For ath9k driver to load successfully, this is overriden in DTS with correct value for this chip, 0x0033. 4. RFKILL button is wired to AR9580 pin 9 which is normally disabled by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore 'qca,gpio-mask=<0xf6ff>' hack must be used for button to work properly. 5. USB port is always on, no GPIO for 5V power control has been identified. Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Diffstat (limited to 'target/linux/ath79/nand/base-files')
-rwxr-xr-xtarget/linux/ath79/nand/base-files/etc/board.d/01_leds3
-rwxr-xr-xtarget/linux/ath79/nand/base-files/etc/board.d/02_network6
-rw-r--r--target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom6
3 files changed, 10 insertions, 5 deletions
diff --git a/target/linux/ath79/nand/base-files/etc/board.d/01_leds b/target/linux/ath79/nand/base-files/etc/board.d/01_leds
index 49d4005495..0376b7cfc6 100755
--- a/target/linux/ath79/nand/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/nand/base-files/etc/board.d/01_leds
@@ -13,7 +13,8 @@ glinet,gl-ar300m-nor)
ucidef_set_led_netdev "lan" "LAN" "gl-ar300m:green:lan" "eth0"
;;
netgear,wndr3700-v4|\
-netgear,wndr4300)
+netgear,wndr4300|\
+netgear,wndr4300-v2)
ucidef_set_led_switch "wan-amber" "WAN (amber)" "netgear:amber:wan" "switch0" "0x20"
;;
esac
diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network
index f7e43addc1..135a06d44b 100755
--- a/target/linux/ath79/nand/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network
@@ -17,7 +17,8 @@ ath79_setup_interfaces()
"0@eth0" "2:lan:2" "3:lan:1" "1:wan"
;;
netgear,wndr3700-v4|\
- netgear,wndr4300)
+ netgear,wndr4300|\
+ netgear,wndr4300-v2)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
;;
@@ -37,7 +38,8 @@ ath79_setup_macs()
case "$board" in
netgear,wndr3700-v4|\
- netgear,wndr4300)
+ netgear,wndr4300|\
+ netgear,wndr4300-v2)
wan_mac=$(mtd_get_mac_binary caldata 0x6)
;;
zyxel,nbg6716)
diff --git a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 25bafe67ac..7ee291d109 100644
--- a/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/nand/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -10,7 +10,8 @@ case "$FIRMWARE" in
"ath9k-eeprom-ahb-18100000.wmac.bin")
case $board in
netgear,wndr3700-v4|\
- netgear,wndr4300)
+ netgear,wndr4300|\
+ netgear,wndr4300-v2)
caldata_extract "caldata" 0x1000 0x440
;;
zyxel,nbg6716)
@@ -25,7 +26,8 @@ case "$FIRMWARE" in
"ath9k-eeprom-pci-0000:00:00.0.bin")
case $board in
netgear,wndr3700-v4|\
- netgear,wndr4300)
+ netgear,wndr4300|\
+ netgear,wndr4300-v2)
caldata_extract "caldata" 0x5000 0x440
;;
*)