kernel: Make the patches apply on top of 4.19

This makes the patches which were just copied in the previous commit
apply on top of kernel 4.19.

The patches in the backports-4.19 folder were checked if they are really
in kernel 4.19 based on the title and only removed if they were found in
the upstream kernel.

The following additional patches form the pending folder went into
upstream Linux 4.19:
pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch
pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch
pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch
pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch
pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch
pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch

Bigger changes were introduced to the m25p80 spi nor driver, as far as I
saw it in the new code, it now has the functionality provided in this
patch:
pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch

Part of this patch went upstream independent of OpenWrt:
hack-4.19/220-gc_sections.patch
This patch was reworked to match the changes done upstream.

The MIPS DMA API changed a lot, this patch was rewritten to match the
new DMA handling:
pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch

I did bigger manual changes to the following patches and I am not 100% sure if they are all correct:
pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch
pending-4.19/411-mtd-partial_eraseblock_write.patch
pending-4.19/600-netfilter_conntrack_flush.patch
pending-4.19/611-netfilter_match_bypass_default_table.patch
pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch
hack-4.19/211-host_tools_portability.patch
hack-4.19/221-module_exports.patch
hack-4.19/321-powerpc_crtsavres_prereq.patch
hack-4.19/902-debloat_proc.patch

This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr>

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

1 files changed, 0 insertions, 50 deletions

diff --git a/target/linux/generic/backport-4.19/071-v4.15-0001-net-bgmac-enable-master-mode-for-BCM54210E-and-B5021.patch b/target/linux/generic/backport-4.19/071-v4.15-0001-net-bgmac-enable-master-mode-for-BCM54210E-and-B5021.patch
deleted file mode 100644
index db239e0a00..0000000000
--- a/target/linux/generic/backport-4.19/071-v4.15-0001-net-bgmac-enable-master-mode-for-BCM54210E-and-B5021.patch
+++ /dev/null
@@ -1,50 +0,0 @@
-From 12acd136913ccdf394eeb2bc8686ff5505368119 Mon Sep 17 00:00:00 2001
-From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
-Date: Thu, 12 Oct 2017 10:21:26 +0200
-Subject: [PATCH] net: bgmac: enable master mode for BCM54210E and B50212E PHYs
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-There are 4 very similar PHYs:
-0x600d84a1: BCM54210E (rev B0)
-0x600d84a2: BCM54210E (rev B1)
-0x600d84a5: B50212E (rev B0)
-0x600d84a6: B50212E (rev B1)
-that need setting master mode manually. It's because they run in slave
-mode by default with Automatic Slave/Master configuration disabled which
-can lead to unreliable connection with massive ping loss.
-
-So far it was reported for a board with BCM47189 SoC and B50212E B1 PHY
-connected to the bgmac supported ethernet device. Telling PHY driver to
-setup PHY properly solves this issue.
-
-Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
-Signed-off-by: David S. Miller <davem@davemloft.net>
----
- drivers/net/ethernet/broadcom/bgmac-bcma.c | 8 +++++++-
- 1 file changed, 7 insertions(+), 1 deletion(-)
-
---- a/drivers/net/ethernet/broadcom/bgmac-bcma.c
-+++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c
-@@ -184,13 +184,19 @@ static int bgmac_probe(struct bcma_devic
- 
- 	if (!bgmac_is_bcm4707_family(core) &&
- 	    !(ci->id == BCMA_CHIP_ID_BCM53573 && core->core_unit == 1)) {
-+		struct phy_device *phydev;
-+
- 		mii_bus = bcma_mdio_mii_register(bgmac);
- 		if (IS_ERR(mii_bus)) {
- 			err = PTR_ERR(mii_bus);
- 			goto err;
- 		}
--
- 		bgmac->mii_bus = mii_bus;
-+
-+		phydev = mdiobus_get_phy(bgmac->mii_bus, bgmac->phyaddr);
-+		if (ci->id == BCMA_CHIP_ID_BCM53573 && phydev &&
-+		    (phydev->drv->phy_id & phydev->drv->phy_id_mask) == PHY_ID_BCM54210E)
-+			phydev->dev_flags |= PHY_BRCM_EN_MASTER_MODE;
- 	}
- 
- 	if (core->bus->hosttype == BCMA_HOSTTYPE_PCI) {