aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/base-files/etc
diff options
context:
space:
mode:
authorDavid Bauer <mail@david-bauer.net>2019-02-18 23:58:34 +0100
committerChristian Lamparter <chunkeey@gmail.com>2019-02-28 11:32:55 +0100
commit95b0c07a618fe5fd93a26931152ced483bba143b (patch)
tree1339e3ba01d820269481ed44368f5c587245c96f /target/linux/ipq40xx/base-files/etc
parent93b02ad95e53113562d76b2752ae43d676f454d5 (diff)
downloadupstream-95b0c07a618fe5fd93a26931152ced483bba143b.tar.gz
upstream-95b0c07a618fe5fd93a26931152ced483bba143b.tar.bz2
upstream-95b0c07a618fe5fd93a26931152ced483bba143b.zip
ipq40xx: add support for FritzBox 7530
Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M FLASH: 128M NAND ETH: QCA8075 VDSL: Intel/Lantiq VRX518 PCIe attached currently not supported DECT: Dialog SC14448 currently not supported WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac LED: - Power/DSL green - WLAN green - FON/DECT green - Connect/WPS green - Info green - Info red BTN: - WLAN - FON - WPS/Connect UART: 115200n8 3.3V (located under the Dialog chip) VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz7530' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ7530.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz7530.bin uboot0 > mtd write /path/to/uboot-fritz7530.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net> [removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Diffstat (limited to 'target/linux/ipq40xx/base-files/etc')
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/01_leds7
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/02_network4
-rw-r--r--target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata8
3 files changed, 16 insertions, 3 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index d23791eab1..dc656cb6ee 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -25,15 +25,16 @@ avm,fritzbox-4040)
ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
;;
+avm,fritzbox-7530 |\
+glinet,gl-b1300)
+ ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
+ ;;
engenius,eap1300)
ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0"
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt"
ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0"
;;
-glinet,gl-b1300)
- ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
- ;;
netgear,ex6100v2 |\
netgear,ex6150v2)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index c0466ba8bc..9c232d49f7 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -33,6 +33,10 @@ ipq40xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
+ avm,fritzbox-7530)
+ ucidef_add_switch "switch0" \
+ "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
+ ;;
compex,wpj428)
ucidef_set_interface_lan "eth0 eth1"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 44421527d2..1264d2ef36 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -135,6 +135,10 @@ case "$FIRMWARE" in
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
+ avm,fritzbox-7530)
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
+ ;;
compex,wpj428 |\
engenius,eap1300 |\
openmesh,a42 |\
@@ -179,6 +183,10 @@ case "$FIRMWARE" in
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
+ avm,fritzbox-7530)
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
+ /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
+ ;;
compex,wpj428 |\
engenius,eap1300 |\
openmesh,a42 |\