diff options
| author | Marek Lindner <marek.lindner@kaiwoo.ai> | 2018-12-14 23:46:53 +0800 |
|---|---|---|
| committer | Petr Štetiar <ynezz@true.cz> | 2020-12-22 19:11:50 +0100 |
| commit | 4871fd2616acb03fefe69b068955dba36eb00770 (patch) | |
| tree | d1d3072b49b66409a8316da0840dc9ec63af7d85 /target/linux/ipq40xx/base-files | |
| parent | ea5bb6bbfee06f44f714aff40c8929505face221 (diff) | |
| download | upstream-4871fd2616acb03fefe69b068955dba36eb00770.tar.gz upstream-4871fd2616acb03fefe69b068955dba36eb00770.tar.bz2 upstream-4871fd2616acb03fefe69b068955dba36eb00770.zip | |
ipq40xx: add support for Plasma Cloud PA2200
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Diffstat (limited to 'target/linux/ipq40xx/base-files')
4 files changed, 9 insertions, 3 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index b9e79c3b68..4361b7c395 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -18,7 +18,8 @@ ipq40xx_setup_interfaces() engenius,emr3500|\ engenius,ens620ext|\ luma,wrtq-329acn|\ - plasmacloud,pa1200) + plasmacloud,pa1200|\ + plasmacloud,pa2200) ucidef_set_interfaces_lan_wan "eth0" "eth1" ;; aruba,ap-303|\ diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index ade0d74341..e50732586a 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -36,7 +36,8 @@ case "$FIRMWARE" in ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32) ;; engenius,eap2200 |\ - openmesh,a62) + openmesh,a62 |\ + plasmacloud,pa2200) caldata_extract "0:ART" 0x9000 0x2f20 ;; linksys,ea8300 |\ @@ -102,6 +103,7 @@ case "$FIRMWARE" in openmesh,a42 |\ openmesh,a62 |\ plasmacloud,pa1200 |\ + plasmacloud,pa2200 |\ qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c2 |\ unielec,u4019-32m) @@ -200,6 +202,7 @@ case "$FIRMWARE" in openmesh,a42 |\ openmesh,a62 |\ plasmacloud,pa1200 |\ + plasmacloud,pa2200 |\ qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c2 |\ unielec,u4019-32m) diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh index 60886071c9..81418fe0ba 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh @@ -48,6 +48,7 @@ platform_do_upgrade_dualboot_datachk() { openmesh,a42) primary_kernel_mtd=8 ;; + plasmacloud,pa2200|\ openmesh,a62) primary_kernel_mtd=10 ;; diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 22e9ffe114..e43225cbb2 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -112,7 +112,8 @@ platform_do_upgrade() { ;; openmesh,a42 |\ openmesh,a62 |\ - plasmacloud,pa1200) + plasmacloud,pa1200 |\ + plasmacloud,pa2200) PART_NAME="inactive" platform_do_upgrade_dualboot_datachk "$1" ;; |