diff options
| author | INAGAKI Hiroshi <musashino.open@gmail.com> | 2018-12-24 15:20:25 +0900 |
|---|---|---|
| committer | Christian Lamparter <chunkeey@gmail.com> | 2019-01-01 16:39:59 +0100 |
| commit | 51fe956c4fbd6ea78f46a4aa835f142e94f32cee (patch) | |
| tree | fd241b09e356baa4150380976314c27d8d71adac /target/linux/ipq806x/base-files/etc/hotplug.d/firmware | |
| parent | 7e9b93fb1b9d1f04df905b77d79ef8a182b2fb83 (diff) | |
| download | upstream-51fe956c4fbd6ea78f46a4aa835f142e94f32cee.tar.gz upstream-51fe956c4fbd6ea78f46a4aa835f142e94f32cee.tar.bz2 upstream-51fe956c4fbd6ea78f46a4aa835f142e94f32cee.zip | |
ipq806x: add support for Buffalo WXR-2533DHP
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
The U-Boot on WXR-2533DHP employs a complicated dual firmware
protection scheme against corruptions of the kernel and rootfs
images. See the notes in buffalo.sh for details.
specifications:
- Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T)
- 512 MB of RAM (DDR3)
- 256 MB of Flash (NAND)
- 4T4R 2.4/5 GHz Wlan (QCA9980)
- 5x 10/100/1000 Mbps Ethernet
- 10x LEDs, 8x keys (6x buttons, 2x slide-switches)
- 2x USB 3.0 Type-A
- 12VDC/4A AC Adapter
- UART through-hole on PCB
- J3: Vcc, GND, TX, RX from USB port side
- 115200n8
Boot instructions for the initramfs image:
1. Prepare the TFTP server with the initramfs image renamed to
"wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10".
2. Press the "AOSS" button while powering on the WXR-2533DHP.
3. Wait until the "Wireless" LED flashes before releasing the AOSS button.
The WXR-2533DHP will grab the image from TFTP server and will boot it.
Flashing instructions:
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to
let it finish the flashing process.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
Diffstat (limited to 'target/linux/ipq806x/base-files/etc/hotplug.d/firmware')
| -rw-r--r-- | target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 8 |
1 files changed, 8 insertions, 0 deletions
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index ba7a8e0b14..e05f2b2c7b 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -79,6 +79,10 @@ board=$(board_name) case "$FIRMWARE" in "ath10k/pre-cal-pci-0000:01:00.0.bin") case $board in + buffalo,wxr-2533dhp) + ath10kcal_extract "ART" 4096 12064 + ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 30) + ;; linksys,ea8500) ath10kcal_extract "art" 4096 12064 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +1) @@ -109,6 +113,10 @@ case "$FIRMWARE" in ;; "ath10k/pre-cal-pci-0001:01:00.0.bin") case $board in + buffalo,wxr-2533dhp) + ath10kcal_extract "ART" 20480 12064 + ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 24) + ;; linksys,ea8500) ath10kcal_extract "art" 20480 12064 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +2) |