diff options
| author | Sven Eckelmann <sven.eckelmann@open-mesh.com> | 2017-11-30 14:30:06 +0100 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2018-01-13 08:00:14 +0100 |
| commit | 86e18f6706e1f2c881fb6a2b9facf108573416e6 (patch) | |
| tree | 5d9fcc9b5552c7b82efad5cedcfe4d4efdecd870 /target/linux/ipq806x/base-files/etc/hotplug.d | |
| parent | c242643d1aba0f065b4a465cd78f0c54dd7cb3b2 (diff) | |
| download | upstream-86e18f6706e1f2c881fb6a2b9facf108573416e6.tar.gz upstream-86e18f6706e1f2c881fb6a2b9facf108573416e6.tar.bz2 upstream-86e18f6706e1f2c881fb6a2b9facf108573416e6.zip | |
ipq806x: add support for OpenMesh A42
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Diffstat (limited to 'target/linux/ipq806x/base-files/etc/hotplug.d')
| -rw-r--r-- | target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 6 |
1 files changed, 6 insertions, 0 deletions
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 4aaa92305b..61b7403160 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -50,6 +50,9 @@ case "$FIRMWARE" in avm,fritzbox-4040) /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config") ;; + openmesh,a42) + ath10kcal_extract "0:ART" 4096 12064 + ;; qcom,ap-dk01.1-c1) ath10kcal_extract "ART" 4096 12064 ;; @@ -60,6 +63,9 @@ case "$FIRMWARE" in avm,fritzbox-4040) /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config") ;; + openmesh,a42) + ath10kcal_extract "0:ART" 20480 12064 + ;; qcom,ap-dk01.1-c1) ath10kcal_extract "ART" 20480 12064 ;; |