aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x/base-files
diff options
context:
space:
mode:
authorChristian Lamparter <chunkeey@gmail.com>2019-10-12 00:49:15 +0200
committerPetr Štetiar <ynezz@true.cz>2020-12-22 19:11:50 +0100
commit98b86296e67dd2b467212fe1a577656e6d3725da (patch)
treed31352bc667bc9b632830bd94503f023d520e820 /target/linux/ipq806x/base-files
parent4d0c442a0a2fdc84ff0dc2c7106455d15c03defe (diff)
downloadupstream-98b86296e67dd2b467212fe1a577656e6d3725da.tar.gz
upstream-98b86296e67dd2b467212fe1a577656e6d3725da.tar.bz2
upstream-98b86296e67dd2b467212fe1a577656e6d3725da.zip
ipq806x: add support for ASRock G10
The ASRock G10 is a 2.4/5 GHz band 11ac "Gaming" router, based on Qualcomm IPQ8064. Specifications: SoC: Qualcomm IPQ8064 CPU: Dual-Core A15 @ (384 - 1,400 MHz, 2C2T) DRAM: 512 MiB (~467 MiB available) NAND: 128 MB (Micron MT29F1G08ABBEAH4) WLAN0: 4T4R 5 GHz Wlan (QCA9980) WLAN1: 4T4R 2.4 GHz Wlan (QCA9980) ETH: 5x 10/100/1000 Mbps Ethernet (QCA8337) INPUT: Reset Button, WPS 2.4G and WPS 5G Button LEDS: 1 multicolor status LED USB: 2x USB 3.0 Type-A POWER: 12VDC/3A AC Adapter + dedicated Power Switch UART: Setting is 115200-8-N-1. 1x4 .1" unpopulated header on the PCB (J6 - very tiny silkscreen next to TX). Pinout: 1. 3v3 (Square - best skipped!), 2. RX, 3. GND, 4. TX WARNING: The serial port needs a TTL/RS-232 3.3v level converter! (Depending on the serial adapter RX and TX might need to be swapped). Note about the IR-Remote: There's a 8-Bit MCU (SONIX SN8F25E21SG) which is controlling the IR-Remote and is fed by the IR-Photodiode. The SoC can talk to the device via I2C. The vendor's GPL archive comes with the source of the interface driver for this as a (character driver), the main control software is however a blob. Installation Instructions: 1. Download factory image to disk 2. Apply factory image via stock web-gui Back to stock: 1. Login to router via ssh 2. run "asrock_g10_back_to_factory" script from /sbin Notes: - If something goes wrong durring sysupgrade, router will go back to factory image. - Asrock G10 uses partition layout from smem. So partition layout can be normal or alternate. - 900-arm-add-cmdline-override.patch was copied from 102-powerpc-add-cmdline-override.patch from powerpc target. Knowledge about BOOTCONFIG partition was based on user "jmomo" post from old OpenWrt forum (Post #50): https://forum.archive.openwrt.org/viewtopic.php?id=65956&p=2 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [bump to 5.4, add factory image, fix sysupgrade, convert partition layout to smem, remove ipq-wifi-asrock-g10 and use ART, minor fixes] Co-Authored-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Lukasz Ostapiuk <palibrzuch@gmail.com>
Diffstat (limited to 'target/linux/ipq806x/base-files')
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/02_network9
-rw-r--r--target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata6
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/init.d/bootcount8
-rw-r--r--target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh14
-rw-r--r--target/linux/ipq806x/base-files/lib/upgrade/asrock.sh55
-rw-r--r--target/linux/ipq806x/base-files/lib/upgrade/platform.sh4
-rwxr-xr-xtarget/linux/ipq806x/base-files/sbin/asrock_g10_back_to_factory16
7 files changed, 108 insertions, 4 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 3f9d96881d..eecf81a8cd 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -12,6 +12,11 @@ board_config_update
board=$(board_name)
case "$board" in
+asrock,g10 |\
+nec,wg2600hp)
+ ucidef_add_switch "switch0" \
+ "2:lan" "3:lan" "4:lan" "5:lan" "6@eth1" "1:wan" "0@eth0"
+ ;;
buffalo,wxr-2533dhp |\
compex,wpq864 |\
netgear,d7800 |\
@@ -41,10 +46,6 @@ linksys,ea8500)
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
;;
-nec,wg2600hp)
- ucidef_add_switch "switch0" \
- "2:lan" "3:lan" "4:lan" "5:lan" "6@eth1" "1:wan" "0@eth0"
- ;;
netgear,r7800 |\
tplink,c2600)
ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 74ad00c5ce..a22af9b676 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -9,6 +9,9 @@ board=$(board_name)
case "$FIRMWARE" in
"ath10k/pre-cal-pci-0000:01:00.0.bin")
case $board in
+ asrock,g10)
+ caldata_extract "0:ART" 0x1000 0x2f20
+ ;;
buffalo,wxr-2533dhp)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ART 0x1e)
@@ -47,6 +50,9 @@ case "$FIRMWARE" in
;;
"ath10k/pre-cal-pci-0001:01:00.0.bin")
case $board in
+ asrock,g10)
+ caldata_extract "0:ART" 0x5000 0x2f20
+ ;;
buffalo,wxr-2533dhp)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ART 0x18)
diff --git a/target/linux/ipq806x/base-files/etc/init.d/bootcount b/target/linux/ipq806x/base-files/etc/init.d/bootcount
index 77965e647b..7a54c34dba 100755
--- a/target/linux/ipq806x/base-files/etc/init.d/bootcount
+++ b/target/linux/ipq806x/base-files/etc/init.d/bootcount
@@ -2,8 +2,16 @@
START=99
+. /lib/upgrade/asrock.sh
+
boot() {
case $(board_name) in
+ asrock,g10)
+ asrock_bootconfig_mangle "bootcheck"
+ if [ $? -eq 0 ]; then
+ reboot
+ fi
+ ;;
edgecore,ecw5410)
fw_setenv bootcount 0
;;
diff --git a/target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh b/target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh
new file mode 100644
index 0000000000..ca8d0b1555
--- /dev/null
+++ b/target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh
@@ -0,0 +1,14 @@
+. /lib/functions.sh
+
+preinit_set_mac_address() {
+ case $(board_name) in
+ asrock,g10)
+ lan_mac=$(mtd_get_mac_ascii hwconfig HW.LAN.MAC.Address)
+ wan_mac=$(mtd_get_mac_ascii hwconfig HW.WAN.MAC.Address)
+ ip link set dev eth0 address "${lan_mac}"
+ ip link set dev eth1 address "${wan_mac}"
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main preinit_set_mac_address
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/asrock.sh b/target/linux/ipq806x/base-files/lib/upgrade/asrock.sh
new file mode 100644
index 0000000000..71cac3faac
--- /dev/null
+++ b/target/linux/ipq806x/base-files/lib/upgrade/asrock.sh
@@ -0,0 +1,55 @@
+. /lib/functions.sh
+
+
+asrock_bootconfig_mangle() {
+ local mtdnum="$( find_mtd_index 0:BOOTCONFIG )"
+
+ if [ -z "$mtdnum" ]; then
+ echo "cannot find bootconfig mtd partition"
+ return 1
+ fi
+ dd if=/dev/mtd$mtdnum of=/tmp/mtd$mtdnum bs=1k
+
+ local partition_byte="$(dd if=/tmp/mtd$mtdnum bs=1 skip=52 count=1)"
+ local upgrade_byte="$(dd if=/tmp/mtd$mtdnum bs=1 skip=4 count=1)"
+
+ if [ $1 = "bootcheck" ]; then
+ if [ ! -s $upgrade_byte ]; then
+ dd if=/dev/mtd$mtdnum of=/tmp/mtd$mtdnum bs=1k
+ printf '\x00' | dd of=/tmp/mtd$mtdnum conv=notrunc bs=1 seek=4
+ printf '\x00' | dd of=/tmp/mtd$mtdnum conv=notrunc bs=1 seek=56
+ else
+ return 1
+ fi
+ elif [ $1 = "sysupgrade" ]; then
+ printf '\x01' | dd of=/tmp/mtd$mtdnum conv=notrunc bs=1 seek=4
+ printf '\x01' | dd of=/tmp/mtd$mtdnum conv=notrunc bs=1 seek=56
+ fi
+
+ if [ -s $partition_byte ]; then
+ printf '\x01' | dd of=/tmp/mtd$mtdnum conv=notrunc bs=1 seek=52
+ else
+ printf '\x00' | dd of=/tmp/mtd$mtdnum conv=notrunc bs=1 seek=52
+ fi
+
+ mtd write /tmp/mtd$mtdnum /dev/mtd$mtdnum
+ return 0
+}
+
+asrock_upgrade_prepare() {
+ local ubidev="$( nand_find_ubi ubi )"
+
+ #Set upgrade flag. If something goes wrong, router will boot with
+ #factory firmware.
+ asrock_bootconfig_mangle 'sysupgrade'
+
+ if [ $? -ne 0 ]; then
+ echo "cannot find bootconfig mtd partition"
+ exit 1
+ fi
+
+ # Just delete these partitions if present and use
+ # OpenWrt's standard names for those.
+ ubirmvol /dev/$ubidev -N ubi_rootfs &> /dev/null || true
+ ubirmvol /dev/$ubidev -N ubi_rootfs_data &> /dev/null || true
+}
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index f61e8ee878..f5d6c5d55d 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -10,6 +10,10 @@ platform_check_image() {
platform_do_upgrade() {
case "$(board_name)" in
+ asrock,g10)
+ asrock_upgrade_prepare
+ nand_do_upgrade "$1"
+ ;;
buffalo,wxr-2533dhp)
buffalo_upgrade_prepare_ubi
CI_ROOTPART="ubi_rootfs"
diff --git a/target/linux/ipq806x/base-files/sbin/asrock_g10_back_to_factory b/target/linux/ipq806x/base-files/sbin/asrock_g10_back_to_factory
new file mode 100755
index 0000000000..55aa91eab6
--- /dev/null
+++ b/target/linux/ipq806x/base-files/sbin/asrock_g10_back_to_factory
@@ -0,0 +1,16 @@
+#!/bin/sh
+
+. /lib/upgrade/asrock.sh
+
+case $(board_name) in
+asrock,g10)
+ asrock_bootconfig_mangle "factory"
+ if [ $? -eq 0 ]; then
+ reboot
+ fi
+ ;;
+*)
+ echo "Unsupported hardware."
+ ;;
+esac
+