octeon: add support for Ubiquiti EdgeRouter 4

Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router.
It has internal power supply and needs c13 power cord.
There are three 10/100/1000 Mbps RJ45/Copper ports and
one 1000 Mbps SFP port connected directly to a SoC.

SoC:
  Octeon Cavium 7130 (Cavium 3)
  Clocked at 1000Mhz

Memory:
  1 GiB (SK hynix H5TQ4G63CFR-RDC × 2)
  DDR3, clocked at 533 Mhz (1066Mhz effective)
Flash:
  - mtd:
    8 MiB (Macronix MX25L6408EMI-12G)
    used for uboot/eeprom
  - emmc:
    4 GiB (SanDisk SDIN7DP2-4G)
    used for kernel+rootfs
Leds: 1x for power status (white/blue, controllable)
  and 4x for ethernet and sfp ports (no control over them)
Buttons: 1x Reset (from SOC)
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC)
USB: 1x USB3.0 on front panel (from SoC)
MII: 1x QSGMII from SoC is used
PHY: 1x Vitesse VSC8504 of which 4x ports is used

All physical port numbers are properly mapped inside OS and
named by lanX instead of ethX.

There is also special purpose four(4) loopX ports available.
That loopX ports are currently hardcoded by linux kernel
and exact use case of them is currently unknown. We leave them
to the linux kernel and octeon board defaults.

All four (4) physical ports are connected to the same QSGMII.
vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used.

Phy mapping:
 - Phy5 is connected to physical eth0 port
 - Phy6 is connected to physical eth1 port
 - Phy7 is connected to physical eth2 port
 - Phy4 is connected to physical eth3 port

Why this device needs external dts:
 - faster boot time since need to initialize less device tree nodes.
 - to add actual indication with LED about boot/failure/upgrade.
   i.e. user could know when to enter failsafe mode or if upgrade is done
 - reset button support so user can reset their device in case off failure
 - sfp port indication in dmesg with information about sfp module
   it also indicates when module inserted or removed

Octeon quirks:
 - There is no port status available before it interface brought up
 - SFP port can not be tied to actual phy due to octeon-ethernet state
   and currently we can only get reports a about SFP state in dmesg

How to flash the firmware:
  - copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and
    openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to
    USB flash drive that is formatted to vfat/fat32
  - connect USB flash drive to edgerouter 4 front USB port
  - connect serial cable using front RJ45 port (115200 baud, 8N1)
  - connect power to cable to edgerouter 4
  - connect terminal to the console to see uboot boot process
  - interrupt boot by pressing button(s) on your keyboard to log in to the uboot
  - detect usb connected flash drives by typing to the console:
    usb start
  - after drive is detected load initramfs+kernel to the memory by typing:
    fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin
  - after initramfs+kernel is loaded to the memory load it by typing:
    bootoctlinux 0 numcores=4 endbootargs mem=0
  - boot process should finish and you will be greeted with console after pressing enter
  - create directory to mount usb flash drive to by typing:
    mkdir /tmp/sda
  - mount flash drive to that directory by typing:
    mount /dev/sda1 /tmp/sda
  - flash firmware to router internal storage by typing:
    sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar
  - device will reboot and after it gets up you will have edgerouter 4 running openwrt

Reviewed-by: Johannes Kimmel <fff@bareminimum.eu>
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>

1 files changed, 357 insertions, 0 deletions

diff --git a/target/linux/octeon/files/arch/mips/boot/dts/cavium-octeon/cn71xx.dtsi b/target/linux/octeon/files/arch/mips/boot/dts/cavium-octeon/cn71xx.dtsi
new file mode 100644
index 0000000000..4b6d1e28d3
--- /dev/null
+++ b/target/linux/octeon/files/arch/mips/boot/dts/cavium-octeon/cn71xx.dtsi
@@ -0,0 +1,357 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+/ {
+	compatible = "cavium,cn71xx";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&ciu>;
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		bootbus@1180000000000 {
+			#address-cells = <2>;
+			#size-cells = <1>;
+			compatible = "cavium,octeon-3860-bootbus";
+			reg = <0x11800 0x00 0x00 0x200>;
+			ranges = <0x00 0x00 0x10000 0x10000000 0x00>,
+				 <0x01 0x00 0x10000 0x20000000 0x00>,
+				 <0x02 0x00 0x10000 0x30000000 0x00>,
+				 <0x03 0x00 0x10000 0x40000000 0x00>,
+				 <0x04 0x00 0x10000 0x50000000 0x00>,
+				 <0x05 0x00 0x10000 0x60000000 0x00>,
+				 <0x06 0x00 0x10000 0x70000000 0x00>,
+				 <0x07 0x00 0x10000 0x80000000 0x00>;
+		};
+
+		dma0: dma-engine@1180000000100 {
+			status = "disabled";
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x100 0x0 0x08>;
+			interrupts = <0 63>;
+		};
+
+		dma1: dma-engine@1180000000108 {
+			status = "disabled";
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x108 0x0 0x08>;
+			interrupts = <0 63>;
+		};
+
+		ciu: interrupt-controller@1070000000000 {
+			#interrupt-cells = <2>;
+			compatible = "cavium,octeon-3860-ciu";
+			reg = <0x10700 0x00000000 0x0 0x7000>;
+			interrupt-controller;
+		};
+
+		cib0: interrupt-controller@107000000e000 {
+			#interrupt-cells = <2>;
+			compatible = "cavium,octeon-7130-cib";
+			reg = <0x10700 0xe000 0x0 0x08>, /* RAW */
+			      <0x10700 0xe100 0x0 0x08>; /* EN */
+			cavium,max-bits = <23>;
+			interrupts = <1 24>;
+			interrupt-parent = <&ciu>;
+			interrupt-controller;
+		};
+
+		cib1: interrupt-controller@107000000e200 {
+			#interrupt-cells = <2>;
+			compatible = "cavium,octeon-7130-cib";
+			reg = <0x10700 0xe200 0x0 0x08>, /* RAW */
+			      <0x10700 0xe300 0x0 0x08>; /* EN */
+			cavium,max-bits = <12>;
+			interrupts = <1 52>;
+			interrupt-parent = <&ciu>;
+			interrupt-controller;
+		};
+
+		cib2: interrupt-controller@107000000e400 {
+			#interrupt-cells = <2>;
+			compatible = "cavium,octeon-7130-cib";
+			reg = <0x10700 0xe400 0x0 0x08>, /* RAW */
+			      <0x10700 0xe500 0x0 0x08>; /* EN */
+			cavium,max-bits = <6>;
+			interrupts = <1 63>;
+			interrupt-parent = <&ciu>;
+			interrupt-controller;
+		};
+
+		cib3: interrupt-controller@107000000e600 {
+			#interrupt-cells = <2>;
+			compatible = "cavium,octeon-7130-cib";
+			reg = <0x10700 0xe600 0x0 0x08>, /* RAW */
+			      <0x10700 0xe700 0x0 0x08>; /* EN */
+			cavium,max-bits = <4>;
+			interrupts = <2 16>;
+			interrupt-parent = <&ciu>;
+			interrupt-controller;
+		};
+
+		cib4: interrupt-controller@107000000e800 {
+			#interrupt-cells = <2>;
+			compatible = "cavium,octeon-7130-cib";
+			reg = <0x10700 0xe800 0x0 0x08>, /* RAW */
+			      <0x10700 0xea00 0x0 0x08>; /* EN */
+			cavium,max-bits = <11>;
+			interrupts = <1 33>;
+			interrupt-parent = <&ciu>;
+			interrupt-controller;
+		};
+
+		cib5: interrupt-controller@107000000e900 {
+			#interrupt-cells = <2>;
+			compatible = "cavium,octeon-7130-cib";
+			reg = <0x10700 0xe900 0x00 0x08>, /* RAW */
+			      <0x10700 0xeb00 0x00 0x08>; /* EN */
+			cavium,max-bits = <11>;
+			interrupts = <1 23>;
+			interrupt-parent = <&ciu>;
+			interrupt-controller;
+		};
+
+		cib6: interrupt-controller@107000000ec00 {
+			#interrupt-cells = <2>;
+			compatible = "cavium,octeon-7130-cib";
+			reg = <0x10700 0xec00 0x0 0x08>, /* RAW */
+			      <0x10700 0xee00 0x0 0x08>; /* EN */
+			cavium,max-bits = <15>;
+			interrupts = <2 17>;
+			interrupt-parent = <&ciu>;
+			interrupt-controller;
+		};
+
+		gpio: gpio-controller@1070000000800 {
+			#interrupt-cells = <2>;
+			#gpio-cells = <2>;
+			compatible = "cavium,octeon-3860-gpio";
+			reg = <0x10700 0x800 0x0 0x100>;
+			interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+				     <0 20>, <0 21>, <0 22>, <0 23>,
+				     <0 24>, <0 25>, <0 26>, <0 27>,
+				     <0 28>, <0 29>, <0 30>, <0 31>;
+			interrupt-controller;
+			gpio-controller;
+		};
+
+		mmc: mmc@1180000002000 {
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-6130-mmc";
+			reg = <0x11800 0x2000 0x0 0x100>,
+			      <0x11800 0x168 0x0 0x20>;
+			interrupts = <1 19>, <0 63>;
+		};
+
+		smi0: mdio@1180000001800 {
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-mdio";
+			reg = <0x11800 0x1800 0x0 0x40>;
+		};
+
+		smi1: mdio@1180000001900 {
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-mdio";
+			reg = <0x11800 0x1900 0x0 0x40>;
+		};
+
+		pip: pip@11800a0000000 {
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-pip";
+			reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+			interface@0 {
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "cavium,octeon-3860-pip-interface";
+				reg = <0>; /* Interface */
+
+				ethernet@0 {
+					status = "disabled";
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0>; /* Port */
+				};
+
+				ethernet@1 {
+					status = "disabled";
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <1>; /* Port */
+				};
+
+				ethernet@2 {
+					status = "disabled";
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <2>; /* Port */
+				};
+
+				ethernet@3 {
+					status = "disabled";
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <3>; /* Port */
+				};
+			};
+
+			interface@1 {
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "cavium,octeon-3860-pip-interface";
+				reg = <1>; /* Interface */
+
+				ethernet@0 {
+					status = "disabled";
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0>; /* Port */
+				};
+
+				ethernet@1 {
+					status = "disabled";
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <1>; /* Port */
+				};
+
+				ethernet@2 {
+					status = "disabled";
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <2>; /* Port */
+				};
+
+				ethernet@3 {
+					status = "disabled";
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <3>; /* Port */
+				};
+			};
+		};
+
+		twsi0: i2c@1180000001000 {
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x1000 0x0 0x200>;
+			interrupts = <0 45>;
+			clock-frequency = <100000>;
+		};
+
+		twsi1: i2c@1180000001200 {
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x1200 0x0 0x200>;
+			interrupts = <0 59>;
+			clock-frequency = <100000>;
+		};
+
+		uctl@118006c000000 {
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			compatible = "cavium,octeon-7130-sata-uctl";
+			reg = <0x11800 0x6c000000 0x00 0x100>;
+			ranges;
+
+			sata@16c0000000000 {
+				status = "disabled";
+				compatible = "cavium,octeon-7130-ahci";
+				reg = <0x16c00 0x00 0x00 0x200>;
+				interrupt-parent = <&cib3>;
+				interrupts = <2 4>;
+			};
+		};
+
+		usb0: uctl@1180068000000 {
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			compatible = "cavium,octeon-7130-usb-uctl";
+			reg = <0x11800 0x68000000 0x00 0x100>;
+			ranges;
+			power = <0x02 0x01 0x00>;
+			refclk-frequency = <100000000>;
+			refclk-type-hs = "pll_ref_clk";
+			refclk-type-ss = "dlmc_ref_clk1";
+
+			xhci0: xhci@1680000000000 {
+				status = "disabled";
+				compatible = "cavium,octeon-7130-xhci", "synopsys,dwc3";
+				reg = <0x16800 0x0 0x10 0x00>;
+				interrupts = <9 4>;
+				interrupt-parent = <&cib4>;
+			};
+		};
+
+		usb1: uctl@1180069000000 {
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			compatible = "cavium,octeon-7130-usb-uctl";
+			reg = <0x11800 0x69000000 0x00 0x100>;
+			ranges;
+			power = <0x02 0x02 0x01>;
+			refclk-frequency = <100000000>;
+			refclk-type-hs = "pll_ref_clk";
+			refclk-type-ss = "dlmc_ref_clk1";
+
+			xhci1: xhci@1690000000000 {
+				status = "disabled";
+				compatible = "cavium,octeon-7130-xhci", "synopsys,dwc3";
+				reg = <0x16900 0x0 0x10 0x00>;
+				interrupts = <9 4>;
+				interrupt-parent = <&cib5>;
+			};
+		};
+
+		uart0: serial@1180000000800 {
+			status = "disabled";
+			compatible = "cavium,octeon-3860-uart", "ns16550";
+			reg = <0x11800 0x800 0x0 0x400>;
+			reg-shift = <3>;
+			interrupts = <0 34>;
+			clock-frequency = <400000000>;
+			current-speed = <115200>;
+		};
+
+		uart1: serial@1180000000c00 {
+			status = "disabled";
+			compatible = "cavium,octeon-3860-uart", "ns16550";
+			reg = <0x11800 0xc00 0x0 0x400>;
+			reg-shift = <3>;
+			interrupts = <0 35>;
+			clock-frequency = <400000000>;
+			current-speed = <115200>;
+		};
+
+		ocla0@11800a8000000 {
+			status = "disabled";
+			compatible = "cavium,octeon-7130-ocla";
+			reg = <0x11800 0xa8000000 0x0 0x500000>;
+			interrupts = <0x08 0x01 0x09 0x01 0x0b 0x01>;
+			interrupt-parent = <&cib6>;
+		};
+
+		spi: spi@1070000001000 {
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3010-spi";
+			reg = <0x10700 0x1000 0x00 0x100>;
+			interrupts = <0 58>;
+			spi-max-frequency = <100000000>;
+		};
+	};
+};