aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
authorMichael Pratt <mcpratt@pm.me>2021-01-10 02:40:00 -0500
committerAdrian Schmutzler <freifunk@adrianschmutzler.de>2021-01-23 12:53:22 +0100
commit96017a60138bdf97d2f1f7e7b519b4ad6ff13b88 (patch)
treecb9004eb460744611bab66c5046aba2321d70b13 /target/linux
parentf52081bcf938efcd910832f3c3713ab9f3ca0738 (diff)
downloadupstream-96017a60138bdf97d2f1f7e7b519b4ad6ff13b88.tar.gz
upstream-96017a60138bdf97d2f1f7e7b519b4ad6ff13b88.tar.bz2
upstream-96017a60138bdf97d2f1f7e7b519b4ad6ff13b88.zip
ath79: add support for Senao Engenius EAP1200H
FCC ID: A8J-EAP1200H Engenius EAP1200H is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ **Specification:** - QCA9557 SOC - QCA9882 WLAN PCI card, 5 GHz, 2x2, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16FG - UART at J10 populated - 4 internal antenna plates (5 dbi, omni-directional) - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset) **MAC addresses:** MAC addresses are labeled as ETH, 2.4G, and 5GHz Only one Vendor MAC address in flash eth0 ETH *:a2 art 0x0 phy1 2.4G *:a3 --- phy0 5GHz *:a4 --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** 2 ways to flash factory.bin from OEM: Method 1: Firmware upgrade page: OEM webpage at 192.168.1.1 username and password "admin" Navigate to "Firmware Upgrade" page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm and wait 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to "192.168.1.1/index.htm" Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** If you have a serial cable, see Serial Failsafe instructions otherwise, uboot-env can be used to make uboot load the failsafe image *DISCLAIMER* The Failsafe image is unique to Engenius boards. If the failsafe image is missing or damaged this will brick the device DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait 3 minutes connect to ethernet and navigate to 192.168.1.1/index.htm select OEM firmware image from Engenius and click upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs to 'vmlinux-art-ramdisk' make available on TFTP server at 192.168.1.101 power board, interrupt boot execute tftpboot and bootm 0x81000000 NOTE: TFTP is not reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software of EAP1200H is a heavily modified version of Openwrt Kamikaze. One of the many modifications is to the sysupgrade program. Image verification is performed simply by the successful ungzip and untar of the supplied file and name check and header verification of the resulting contents. To form a factory.bin that is accepted by OEM Openwrt build, the kernel and rootfs must have specific names... openwrt-ar71xx-generic-eap1200h-uImage-lzma.bin openwrt-ar71xx-generic-eap1200h-root.squashfs and begin with the respective headers (uImage, squashfs). Then the files must be tarballed and gzipped. The resulting binary is actually a tar.gz file in disguise. This can be verified by using binwalk on the OEM firmware images, ungzipping then untaring. Newer EnGenius software requires more checks but their script includes a way to skip them, otherwise the tar must include a text file with the version and md5sums in a deprecated format. The OEM upgrade script is at /etc/fwupgrade.sh. OKLI kernel loader is required because the OEM software expects the kernel to be no greater than 1536k and the factory.bin upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode`. Therefore the PLL registers for GMAC0 do not need the bits for delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
Diffstat (limited to 'target/linux')
-rw-r--r--target/linux/ath79/dts/qca9557_engenius_eap1200h.dts187
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata1
-rw-r--r--target/linux/ath79/image/generic.mk11
4 files changed, 200 insertions, 0 deletions
diff --git a/target/linux/ath79/dts/qca9557_engenius_eap1200h.dts b/target/linux/ath79/dts/qca9557_engenius_eap1200h.dts
new file mode 100644
index 0000000000..72a50c922e
--- /dev/null
+++ b/target/linux/ath79/dts/qca9557_engenius_eap1200h.dts
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mtd/partitions/uimage.h>
+
+/ {
+ compatible = "engenius,eap1200h", "qca,qca9557";
+ model = "EnGenius EAP1200H";
+
+ aliases {
+ label-mac-device = &eth0;
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "amber:power";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wifi2g {
+ label = "blue:wifi2g";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wifi5g {
+ label = "green:wifi5g";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wps {
+ label = "blue:wps";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ virtual_flash {
+ compatible = "mtd-concat";
+
+ devices = <&fwconcat0 &fwconcat1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ compatible = "openwrt,uimage", "denx,uimage";
+ openwrt,ih-magic = <IH_MAGIC_OKLI>;
+ label = "firmware";
+ reg = <0x0 0x0>;
+ };
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition@50000 {
+ label = "custom";
+ reg = <0x050000 0x050000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "loader";
+ reg = <0x0a0000 0x010000>;
+ read-only;
+ };
+
+ fwconcat1: partition@b0000 {
+ label = "fwconcat1";
+ reg = <0x0b0000 0x170000>;
+ };
+
+ partition@220000 {
+ label = "fakeroot";
+ reg = <0x220000 0x010000>;
+ read-only;
+ };
+
+ fwconcat0: partition@230000 {
+ label = "fwconcat0";
+ reg = <0x230000 0xb40000>;
+ };
+
+ partition@d70000 {
+ label = "failsafe";
+ reg = <0xd70000 0x280000>;
+ read-only;
+ };
+
+ art: partition@ff0000 {
+ label = "art";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ eee-broken-100tx;
+ eee-broken-1000t;
+ };
+};
+
+&eth0 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+
+ phy-handle = <&phy5>;
+ phy-mode = "rgmii-id";
+
+ pll-data = <0x82000000 0x80000101 0x80001313>;
+};
+
+&pcie0 {
+ status = "okay";
+
+ wifi@0,0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x0 0 0 0 0>;
+ qca,no-eeprom;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <1>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 0c08871f99..2d76d16f9f 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -32,6 +32,7 @@ ath79_setup_interfaces()
dlink,dap-2680-a1|\
dlink,dap-3320-a1|\
dlink,dir-505|\
+ engenius,eap1200h|\
engenius,eap300-v2|\
engenius,eap600|\
engenius,ecb1200|\
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 84323046f6..9a199b4deb 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -11,6 +11,7 @@ case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
allnet,all-wap02860ac|\
+ engenius,eap1200h|\
engenius,enstationac-v1|\
glinet,gl-x750)
caldata_extract "art" 0x5000 0x844
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 3b5cb6bdfa..7432607fcd 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -957,6 +957,17 @@ define Device/embeddedwireless_dorin
endef
TARGET_DEVICES += embeddedwireless_dorin
+define Device/engenius_eap1200h
+ $(Device/engenius_loader_okli)
+ SOC := qca9557
+ DEVICE_MODEL := EAP1200H
+ DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
+ IMAGE_SIZE := 11520k
+ LOADER_FLASH_OFFS := 0x230000
+ ENGENIUS_IMGNAME := ar71xx-generic-eap1200h
+endef
+TARGET_DEVICES += engenius_eap1200h
+
define Device/engenius_eap300-v2
$(Device/engenius_loader_okli)
SOC := ar9341